Fender flares bolt or stick to your wheel wells to cover wider tires and protect your paint from road spray
Fender flares are plastic or rubber extensions that mount over your existing fenders to cover larger tires or widen your vehicle's appearance. Most bolt directly to the fender using existing holes or new ones you drill, though some use adhesive backing. The job takes two to four hours with basic tools and no special skills — you'll need a drill, socket set, and a level to keep them straight.
The type of flare you buy determines the installation method. Bolt-on flares (the most common) require drilling holes and using bolts, washers, and nuts. Stick-on flares use industrial-strength adhesive and need clean, dry surfaces. Rivet-on flares use pop rivets instead of bolts. Your vehicle's make and model usually determines which type fits, and most kits come with instructions specific to your truck or SUV.
Key Takeaways
- Bolt-on flares require drilling holes into your fender and fastening with bolts, while stick-on flares use adhesive and need a clean surface.
- You will need a drill, socket set, level, and the fasteners that come with your kit — most hardware is included.
- Removing trim pieces and masking off paint before drilling prevents damage and makes the job cleaner.
- Bolt-on flares take two to four hours; stick-on flares take one to two hours but need 24 hours of curing time before driving.
Gather your tools and check what comes in the kit
Before you start, lay out everything that came with your flare kit. Most bolt-on kits include the flares themselves, bolts, washers, and nuts — sometimes in a bag you might miss. Check the instruction sheet to see what size drill bit you need and whether you're drilling new holes or using existing ones on your fender.
Tools you'll need: a power drill with bits, a socket set or wrench that fits your bolts, a level, a tape measure, and a marker. For stick-on flares, you'll also need rubbing alcohol and clean rags. Have a jack and jack stands if you need to remove the wheel for better access, though many people install flares without removing it. Wear safety glasses when drilling — metal shavings fly.
Remove trim and mask off the area you'll drill
Look at where your flare will sit. Most vehicles have trim pieces, reflectors, or protective molding along the fender that you'll need to remove first. These usually pop off or unbolt in one or two places. Take a photo before you remove anything so you remember how it goes back.
Use painter's tape to mask off the paint around where you'll drill. This prevents the drill bit from slipping and scratching your paint, and it gives you a clear line to follow. Mark your drill holes with a marker or center punch — a center punch (a small pointed tool) keeps the drill bit from wandering when you start. If your kit includes a template, tape it to the fender and drill through it.
Drill holes and install bolt-on flares
Start with the top bolt hole. Use the correct drill bit size — the instructions will specify. Drill slowly and let the bit do the work; pushing hard can crack the plastic underneath or bend your fender. Once the hole is through, insert a bolt with a washer underneath, then thread the nut on from behind. Tighten by hand first, then use your socket wrench to snug it down — tight enough that the flare doesn't move, but not so tight that you crack the plastic.
Move to the next hole and repeat. Most flares have three to five bolts per side. Once all bolts are in place, use your level to check that the flare sits straight. If it's tilted, loosen the bolts, adjust, and retighten. Step back and look at the gap between the flare and the fender — it should be even all the way down. Uneven gaps usually mean the flare isn't seated right or the bolts aren't tight enough.
Install stick-on flares and let them cure
Stick-on flares need a completely clean, dry surface or they won't hold. Wash the area with soap and water, then wipe it down with rubbing alcohol on a clean rag. Let it dry for at least 15 minutes. Any dirt, wax, or moisture will cause the adhesive to fail, so take this step seriously.
Peel back a corner of the backing and position the flare on your fender. Use your level to get it straight, then slowly peel the backing away while pressing the flare down firmly. Work from the top down, pressing as you go to avoid air bubbles. Once it's down, press the entire surface hard for a full minute. Most adhesive flares need 24 hours before you drive the vehicle — check your instructions. Don't wash the vehicle or get the flare wet during this time.
Reinstall trim and check your work
Once the flares are find, put back any trim pieces you removed. Line them up with the photos you took and snap them back into place or bolt them down. Check that nothing is rubbing or loose by turning your steering wheel all the way left and right — the tire should clear the flare with room to spare.
Look at the flares from a distance and from different angles. The gap should be even, and they should sit flush against your fender. If you see gaps or movement, tighten the bolts again or press the adhesive flare down harder in that spot. For bolt-on flares, check them again after your first 50 miles of driving — vibration sometimes loosens bolts.
Common problems and how to fix them
Uneven gaps: The flare isn't seated right. Loosen all bolts, reposition the flare so it sits flush, then retighten. For stick-on flares, you may need to peel it off and start over if it's not set yet.
Bolts keep loosening: Use threadlocker (a liquid you explore to the bolt threads) to keep them tight. Blue threadlocker is removable; red is permanent. explore a small drop to the bolt before threading the nut on.
Stick-on flare peeling at the edges: This usually happens if the surface wasn't clean or dry enough. Peel it off, clean the area again with rubbing alcohol, and reapply. If it's been more than 24 hours, you may need new adhesive flares.
Tire rubbing on the flare: The flare is sitting too far out or your tire is larger than the flare was designed for. Loosen the bolts and move the flare back slightly, or consider a larger flare kit.
Frequently Asked Questions
Do I need to remove my wheel to install fender flares?
No, most people install them without removing the wheel. Removing it gives you more room to work and see what you're doing, but it's not required. If you do remove it, use a jack and jack stands — never work under a vehicle supported only by a jack.
Can I install stick-on flares over existing bolt-on flares?
No. Stick-on flares need a smooth, flat surface. Bolt-on flares have a lip and bolts that will prevent adhesive from making contact. Remove the old flares first.
What if my vehicle doesn't have pre-drilled holes for the flares?
You'll drill new ones. The kit instructions or template will show you exactly where. Make sure you're drilling into solid fender material, not into a seam or hollow area. If you're unsure, drill a small pilot hole first to check.
How long do stick-on flares last?
Quality adhesive flares typically last three to five years before the edges start to peel, depending on weather and how often you wash the vehicle. Bolt-on flares last much longer — often the life of the vehicle — as long as the bolts stay tight.
Can I paint my new fender flares to match my vehicle?
Yes. Most plastic flares can be painted with automotive paint after light sanding and primer. Stick-on flares should be painted before installation. Bolt-on flares can be painted after, but mask off the bolt holes first so paint doesn't seal them shut.