Where to find your wheel offset
Your wheel offset is stamped directly on the back of each wheel, usually near the center where the wheel bolts to the hub. Look for a series of numbers and letters — the offset appears as a number followed by "mm" (millimeters), often preceded by "ET" (a German abbreviation meaning "Einpresstiefe"). For example, "ET45" means 45 millimeters of positive offset.
If the wheels are dirty or the stamp is worn, you may need to clean the back surface or use a flashlight to read it clearly. The offset is almost always on the inboard side — the side facing the vehicle's frame, not the outside. If you cannot locate it on the wheel itself, your vehicle's original offset is listed in the owner's manual or on the placard inside the driver's side door jamb, though that placard typically shows tire size rather than wheel specifications.
When buying replacement or aftermarket wheels, the offset number is always provided by the seller or manufacturer. If you are shopping online or at a tire shop, ask for the offset before purchase — it is a standard specification that any reputable seller can provide when ready.
Key Takeaways
- Wheel offset is stamped on the back of the wheel near the center, usually marked as "ET" followed by a number in millimeters.
- Positive offset means the mounting surface is toward the outside of the wheel; negative offset means it is toward the inside.
- Your vehicle's original offset is documented in the owner's manual or by contacting the manufacturer with your vehicle identification number (VIN).
- Aftermarket wheel sellers must provide the offset specification before you purchase, and it should match your vehicle's requirements or be within the safe range for your suspension.
What wheel offset means and why it matters
Offset is the distance in millimeters between the wheel's mounting surface (where it bolts to the hub) and the centerline of the wheel. This measurement determines how far the wheel sits from the vehicle's frame and suspension. A wheel with 45mm offset sits differently than one with 35mm offset, even if both are the same diameter and width.
Offset affects how the wheel and tire sit relative to the fender and suspension components. Too much negative offset (wheel pushed inward) can cause the tire to rub the inside of the fender or suspension parts during turns or bumps. Too much positive offset (wheel pulled outward) can cause the tire to rub the outside of the fender or stick out beyond the vehicle's body. Either situation can damage the tire, fender, or suspension and may violate local vehicle code.
The offset also influences the load on wheel bearings and suspension geometry. Changing offset from the manufacturer's specification changes how weight is distributed through the suspension, which can affect handling, tire wear, and brake performance. This is why offset must stay within a narrow range — usually within 5 to 10 millimeters of the original specification, depending on the vehicle.
How to read the wheel stamp
A typical wheel stamp looks like this: "5x114.3 ET45 73.1 J7". Each part tells you something different. The "ET45" is the offset — 45 millimeters. The "5x114.3" is the bolt pattern (5 bolts, 114.3 millimeters apart). The "73.1" is the center bore diameter. The "J7" describes the wheel's rim shape and width.
The offset number can be positive or negative. Positive numbers (ET45, ET50) mean the mounting surface is closer to the outside of the wheel. Negative numbers (ET-10, ET-5) mean the mounting surface is closer to the inside. Zero offset (ET0) means the mounting surface is exactly at the wheel's centerline. Most passenger vehicles use positive offset ranging from ET25 to ET50.
If you see multiple stamps on the wheel, look for the one that includes "ET" — that is the offset. Some wheels have manufacturing dates, load ratings, or other information stamped elsewhere. The offset stamp is usually the most prominent and is always on the inboard (inner) side of the wheel.
Finding offset for your specific vehicle
The easiest way to find your vehicle's original offset is to check the owner's manual under the wheel or tire specifications section. Many manuals list the complete wheel specification including offset. If your manual does not include it, contact the vehicle manufacturer directly with your VIN — they can tell you the exact offset for your model year and trim level.
You can also visit a tire shop or dealership and ask them to look up your vehicle's specifications in their system. They have access to manufacturer databases and can provide the original offset in minutes. Some shops charge a small fee for this service, but many provide it free if you are considering purchasing tires or wheels from them.
If you own an aftermarket wheel already and want to know its offset, measure it yourself using a straight edge and ruler. Place a straight edge across the back of the wheel (the inboard side) so it touches both edges of the rim. Measure from that straight edge to the mounting surface — that distance is your offset. This method is less precise than the stamped number but works if the stamp is illegible.
What happens if you use the wrong offset
Using wheels with incorrect offset can cause tire rubbing, which damages both the tire and the vehicle's body or suspension. Rubbing usually happens during hard turns, when the suspension compresses, or when driving over bumps. You may hear a scraping or squealing sound from the wheel area, or notice visible damage to the tire sidewall or fender.
Incorrect offset also changes the scrub radius — the angle at which the tire contacts the road relative to the steering axis. This affects steering feel, stability, and how the vehicle handles during braking. Some drivers report that wheels with significantly different offset cause the steering wheel to feel heavier or the vehicle to pull to one side.
In some jurisdictions, wheels that extend beyond the vehicle's body line or cause rubbing may fail a vehicle inspection or be considered a safety violation. Before installing aftermarket wheels, confirm that their offset falls within the acceptable range for your vehicle. Most manufacturers allow a variance of plus or minus 5 millimeters from the original offset, but this varies by vehicle — check your manual or contact the manufacturer to be certain.
Measuring offset if you need to verify it
If you have a wheel in front of you and the stamp is missing or illegible, you can measure offset using basic tools. You need a straight edge (a level or long ruler works), a tape measure, and the wheel's width in millimeters — which is usually stamped on the wheel as well (for example, "7.5J" means 7.5 inches wide).
Place the wheel face-down on a flat surface. Lay the straight edge across the back of the wheel so it touches both the inner and outer edges of the rim. Measure the distance from the straight edge to the wheel's mounting surface (the center where the lug bolts are). That distance is your offset. If the mounting surface is closer to the outside edge, the offset is positive. If it is closer to the inside edge, the offset is negative.
This method gives you an approximate offset, usually within a few millimeters of the actual stamp. For precise confirmation, always rely on the stamped number if it is readable, or contact the wheel manufacturer with the wheel's model number.
Frequently Asked Questions
Can I use wheels with a different offset than my original wheels?
You can use wheels with a slightly different offset — usually within 5 to 10 millimeters of the original — but you should verify this with your vehicle's manufacturer or a suspension specialist before purchasing. Larger differences risk tire rubbing, suspension damage, or handling problems. Always check your owner's manual or contact the manufacturer with your VIN to confirm the acceptable range for your specific vehicle.
What is the difference between positive and negative offset?
Positive offset means the mounting surface is closer to the outside of the wheel, pushing the wheel outward relative to the suspension. Negative offset means the mounting surface is closer to the inside, pulling the wheel inward. Most passenger cars use positive offset. Trucks and performance vehicles sometimes use negative offset for a wider stance, but this requires suspension modifications to avoid rubbing.
Where do I find offset if I am buying used wheels?
Ask the seller to read the stamp on the back of the wheel or provide the wheel's model number and manufacturer. You can then contact the manufacturer to confirm the offset. If the seller cannot provide this information, do not purchase the wheels — you need to know the offset before installing them to may support they fit your vehicle safely.
Does offset affect tire size or speed rating?
No. Offset is independent of tire size and speed rating. You can have two wheels of the same size and speed rating with different offsets. However, changing offset can affect how much load the wheel and suspension bear, so it is important to stay within the manufacturer's recommended range regardless of tire specifications.
What if the offset stamp is worn off or illegible?
Contact the wheel manufacturer with the wheel's model number or serial number if it is visible. If you cannot identify the manufacturer, you can measure the offset using a straight edge and tape measure as described above. For critical applications, have a suspension specialist measure it to may support accuracy before installation.