The quickest way to find your rim offset

Your rim offset is stamped directly on the wheel itself — look on the back side of the rim, near the center, for a series of numbers and letters. The offset measurement appears as a number preceded by "ET" (European standard) or sometimes just as a plain number. For example, "ET45" or "+35" means the rim has a 45mm or 35mm offset. If you cannot find it on the wheel, check your vehicle's original paperwork, the tire placard on the driver's door jamb, or contact the wheel manufacturer with your wheel size and model number.

Offset is the distance in millimeters between the wheel's mounting surface and its centerline. A positive offset (most common on sedans and crossovers) means the mounting surface sits toward the outside of the wheel. A negative offset (common on trucks and performance vehicles) means it sits toward the inside. Zero offset means the mounting surface is exactly at the wheel's center. This measurement directly affects how your wheels sit in the wheel well and how your suspension handles.

Key Takeaways

  • Rim offset is stamped on the back of the wheel as "ET" followed by a number, such as ET45 or ET35.
  • The original offset for your vehicle is listed on the tire placard attached to your driver's door jamb or inside the fuel door.
  • Offset is measured in millimeters and determines how far the wheel sits from the vehicle's centerline, affecting handling and clearance.
  • Changing offset by more than 5mm from the factory specification can cause rubbing, suspension stress, or speedometer errors.

Reading the stamp on your wheel

The offset stamp is located on the inboard side of the rim — the side facing the vehicle's frame. You will need to remove the wheel or get under the vehicle to see it clearly. The stamp includes several pieces of information: the wheel size (such as 17x7.5), the offset (ET45), the bolt pattern (5x114.3), and sometimes the manufacturer's name or load rating.

The offset number always appears after "ET" on most wheels, regardless of brand. Some aftermarket wheels use a plus or minus sign instead ("+45" or "-12"), which means the same thing. If the number is positive, the mounting surface is pushed outward; if negative, it is pushed inward. The larger the positive number, the more the wheel tucks into the wheel well. The larger the negative number, the more the wheel sticks out.

Finding offset on your original equipment wheels

If you no longer have the wheels or cannot read the stamp clearly, your vehicle's documentation contains the factory offset. Check the tire placard on the driver's side door jamb (the vertical strip where the door closes) — it lists the original wheel size and offset. You can also find this information in your owner's manual under the wheels and tires section, or on a sticker inside the fuel door on some vehicles.

If you have lost all paperwork, contact your vehicle's manufacturer with your vehicle identification number (VIN). They can tell you the exact offset of the wheels that came from the factory. Alternatively, a tire shop or wheel specialist can measure your existing wheels if they are still on the vehicle, though this requires removing them.

Measuring offset yourself if the stamp is worn or missing

If the stamp is too worn to read, you can measure offset manually with basic tools. Remove the wheel and place it flat on a level surface with the inboard side facing up. Measure the distance from the wheel's outer edge to the mounting surface (the flat area where the wheel bolts to the hub). Then measure the total width of the wheel from edge to edge. Subtract the first measurement from half the total width — the result is your offset in millimeters.

This method requires a straight edge, a tape measure, and patience, but it works. For example, if your wheel is 8 inches (203mm) wide and the mounting surface is 3.5 inches (89mm) from the outer edge, your offset is roughly 203 ÷ 2 − 89 = 12mm. This is an approximation and may not be exact, but it gives you a ballpark figure. For precision, a wheel specialist with calipers can measure to within 1mm.

Why offset matters when replacing wheels

Offset affects how your wheels sit relative to your suspension and frame. Staying within 5mm of the factory offset keeps your vehicle handling, braking, and speedometer reading as designed. Going beyond that range can cause the wheel to rub the inside of the fender or suspension components during turns or over bumps, damage your wheel bearings through added stress, or throw off your speedometer by up to 3 percent.

A wheel with too much positive offset (tucked too far in) can rub the inside of the fender or suspension. A wheel with too much negative offset (sticking out too far) can rub the outside of the fender, look wrong in the wheel well, and put extra load on your wheel bearings and suspension. If you are shopping for aftermarket wheels, always match the offset to the factory specification or stay within 5mm of it unless you are modifying the suspension as well.

Where to find offset information for aftermarket wheels

Aftermarket wheel manufacturers always list offset in their product specifications. Check the wheel's product page on the retailer's website, the manufacturer's catalog, or the paperwork that came with the wheels. The offset is usually listed alongside the wheel size, bolt pattern, and weight. If you are buying used wheels from a private seller or online marketplace, ask the seller for the offset or measure it yourself before purchase.

Many wheel retailers have online fitment tools that show you which offsets are available for your vehicle. Enter your vehicle's year, make, and model, and the tool will show wheels that fit your bolt pattern and suspension. These tools often highlight the factory offset so you can see how far each option deviates from it. This is a useful way to compare options before you buy.

Frequently Asked Questions

What happens if I use wheels with the wrong offset?

The wrong offset can cause the wheel to rub the fender or suspension, especially during turns or over bumps. It also puts extra stress on your wheel bearings and suspension components, shortens their lifespan, and can throw off your speedometer. Staying within 5mm of factory offset avoids these problems.

Can I change my offset by more than 5mm?

You can, but it requires other changes. Lowering the suspension or adding spacers can accommodate a larger negative offset, and adjusting the suspension geometry can work with a larger positive offset. These modifications are expensive and affect handling, so they are usually done only for appearance or performance builds, not for everyday driving.

Is ET the same as offset?

Yes. ET is the European standard abbreviation for offset and stands for "Einpresstiefe," which means the distance from the wheel's centerline to the mounting surface. You will see it on most wheels worldwide. Some wheels use a plus or minus sign instead, but they mean the same thing.

Do all four wheels need the same offset?

Yes. All four wheels on your vehicle should have the same offset to keep the suspension balanced and the vehicle handling evenly. Mixing offsets can cause uneven tire wear, pulling to one side, and suspension stress.

Where is the offset stamp located on the wheel?

The offset stamp is on the back (inboard) side of the rim, usually near the center where the wheel bolts to the hub. You need to remove the wheel or get under the vehicle to see it. It appears as "ET" followed by a number, such as ET45 or ET35.