What a car relay does and why it matters

A relay is an electromagnetic switch that uses a small electrical current to control a larger one. In your car, relays handle high-power circuits — your starter motor, fuel pump, cooling fan, headlights, and windshield wipers all run through relays. When a relay fails, the circuit it controls stops working, even though the fuse may be fine and the battery has power.

A failing relay usually makes a clicking sound when you turn the key or press a button. You might hear rapid clicking from under the hood, or the component controlled by that relay straightforward won't work. Because relays are cheap (usually $5 to $20) and straightforward to swap, testing one takes minutes and can save you a trip to the shop.

Key Takeaways

  • A relay that is failing typically makes a rapid clicking noise when you set up the circuit it controls, or the component stops working entirely.
  • Most relays are located in fuse boxes under the hood or inside the cabin, and your owner's manual or a diagram on the fuse box lid shows which relay does what.
  • You can test a relay with a multimeter set to resistance mode, or swap it with an identical relay from another circuit to see if the problem moves.
  • If a relay tests bad, you can replace it yourself by pulling it straight out and pushing a new one in — no tools required.

Locating the relay in your car

Relays live in fuse boxes, and most cars have two: one under the hood near the engine, and one inside the cabin (usually under the dashboard on the driver's side, or behind a panel in the center console). Open the fuse box cover and look for a diagram printed on the inside of the lid or on a label nearby. This diagram shows every relay and fuse, tells you what each one controls, and gives its amperage rating.

If you cannot find a diagram on the box itself, check your owner's manual — it will have a full fuse and relay map with locations. Write down the relay number or name (for example, "Fuel Pump Relay" or "Relay 5") and its position in the box. Relays are usually larger and taller than fuses, and they have a plastic body with metal pins on the bottom.

If you are not sure which relay controls the circuit that is failing, listen for the clicking sound with the hood open and the engine off. Turn on the headlights, wipers, or whatever is not working, and listen for the rapid clicking to pinpoint the relay location.

Testing a relay with a multimeter

A multimeter set to resistance mode (the ohm setting, marked with the Greek letter Ω) can tell you whether a relay's internal switch is stuck. Pull the relay straight out of the fuse box. Set your multimeter to ohms and touch the probes to two of the relay's pins — the exact pins depend on the relay type, but your multimeter manual or the relay's data sheet will show which ones to test.

A good relay will show a reading of 0 to 10 ohms (very low resistance) when the switch is closed, or infinite resistance (shown as "OL" or a very high number) when the switch is open. If the relay shows the same reading no matter which pins you test, or if it shows infinite resistance on pins that should be closed, the relay is likely bad. Write down the reading and compare it to the relay's specifications if you have them.

This test is not foolproof — some relays fail only when they are hot or under load — but it catches most dead relays. If the multimeter test is unclear, move to the swap test instead.

The swap test: the fastest way to confirm a bad relay

The easiest way to know if a relay is bad is to swap it with an identical relay from another circuit you know is working. Find another relay in the same fuse box that is the same size and shape, and note what circuit it controls (make sure that circuit works normally). Pull both relays out, swap their positions, and test the original circuit again.

If the problem moves to the other circuit — meaning the headlights now work but the wipers stop, for example — the relay you swapped out is bad. If the problem stays in the original circuit, the relay is probably fine and the issue is elsewhere (wiring, a switch, or the component itself). This test works because you are using a relay you know is good, and you can see the result when ready.

Keep in mind that not all relays are identical. A relay for the fuel pump may look like a relay for the cooling fan but have different internal wiring. Swap only relays that are the same part number or that control similar circuits (both high-amperage, for example). Your fuse box diagram will tell you which relays are interchangeable.

Replacing a failed relay

Once you have confirmed a relay is bad, replacement takes seconds. Pull the bad relay straight out of the fuse box — it should come out with light pressure. Do not force it; if it is stuck, wiggle it gently side to side. Buy a new relay with the same part number (your parts store can look this up by your car's year, make, and model, plus the relay location). Push the new relay into the empty socket until it clicks into place.

Turn on the circuit and test it. The component should work when ready. If it does not, the relay was not the problem — the issue is likely a blown fuse, a bad switch, damaged wiring, or a failed component. Check the fuse for that circuit first (a blown fuse is black or discolored inside), and if the fuse is good, you may need a mechanic to trace the wiring.

When a relay keeps failing

If you replace a relay and it fails again within weeks or months, something else in that circuit is drawing too much current and burning out the relay. This usually means a component is shorted or failing — the fuel pump motor, the cooling fan motor, or a solenoid. A relay should last the life of the car under normal conditions.

If a relay fails repeatedly, do not keep replacing it. Have a mechanic test the component that relay controls. Replacing the relay again will only mask the real problem and may eventually damage the wiring or fuse box. A diagnostic test of that circuit will find the short or failed component.

Frequently Asked Questions

Can I test a relay without a multimeter?

Yes. The swap test is faster and does not require any tools. Pull the suspected bad relay and swap it with an identical relay from another working circuit. If the problem moves to the other circuit, the relay is bad. This works because you are using a relay you know is good.

What does a clicking sound under the hood mean?

Rapid clicking usually means a relay is trying to switch on and off repeatedly because the circuit it controls is drawing too much current or is shorted. It can also mean the relay itself is failing. Turn off the circuit and listen to pinpoint which relay is clicking, then test or swap it.

Is it safe to swap relays myself?

Yes, as long as you swap relays of the same type and size. Relays have no polarity — they work the same way in either direction. Make sure the engine is off and the key is out of the ignition before you pull or push any relays. If you are unsure whether two relays are the same, check their part numbers on the relay body.

How much does a new relay cost?

Most relays cost between $5 and $20 at an auto parts store. Some specialty relays (for high-end or luxury cars) may cost more. You can also order them online. Bring your car's year, make, and model, plus the relay location from your fuse box diagram, and the parts store will find the exact relay you need.

What if the fuse for that circuit is blown?

Replace the fuse first. A blown fuse looks black or discolored inside the plastic body. If the new fuse blows when ready, there is a short in that circuit — do not keep replacing fuses. Have a mechanic check the wiring and the component that circuit controls.