What an ignition coil does and why it fails
Your ignition coil converts low voltage from the battery into the high voltage needed to fire your spark plugs. When it fails, your engine won't start, or it will misfire and run rough. A bad coil is one of the most common reasons for a check engine light, and it's one of the few things you can test yourself before spending money at a shop.
Ignition coils fail because of heat, moisture, and electrical stress. Modern coils are packed tightly in the engine bay where temperatures spike during operation. If water gets inside the coil housing—from a cracked seal or a flooded engine—the windings inside corrode and lose conductivity. You'll notice symptoms like hard starting, rough idle, hesitation under acceleration, or a cylinder misfiring on one bank.
The good news: you don't need a mechanic's scanner to know whether your coil is dead. You can do a resistance test with a multimeter in about ten minutes, and that test tells you whether the coil is worth replacing or whether the problem is somewhere else in the ignition system.
Key Takeaways
- A multimeter set to the ohms (resistance) setting can tell you whether a coil's internal windings are intact or burned out.
- Primary resistance (the low-voltage side) typically reads between 0.4 and 2 ohms, and secondary resistance (the high-voltage side) typically reads between 6,000 and 30,000 ohms—check your owner's manual or the coil label for your exact specs.
- If your multimeter shows infinite resistance or zero resistance on either test, the coil is failed and needs replacement.
- A coil that passes the resistance test but your engine still misfires means the problem is likely a bad spark plug, a fuel injector issue, or a wiring connection rather than the coil itself.
Gather the right tools and locate your coil
You need a digital multimeter (not an analog one—digital is more accurate for this test). They cost between $15 and $40 at any auto parts store or hardware store. You'll also need a socket set or wrench to remove the coil from the engine, and a clean, dry workspace.
Locate your ignition coil by opening the hood and looking for a cylindrical or rectangular component sitting on top of or near the spark plugs. On older vehicles, there's usually one coil per engine. On newer vehicles, there's often one coil per cylinder, mounted directly on top of each spark plug. Check your owner's manual if you can't find it—the manual will show you exactly where it is and how to disconnect it safely.
Before you touch anything, let the engine cool for at least 30 minutes. Ignition coils get hot during operation, and you can burn yourself. Disconnect the negative terminal of your battery using a wrench—this prevents accidental shorts while you're working.
Remove the coil and prepare it for testing
Unplug the electrical connector from the coil by pressing the release tab or clip and pulling straight back. Take a photo of the connector with your phone before you disconnect it, so you remember which way it goes back in. Some connectors are keyed so they only fit one way, but others aren't.
Remove the bolt or bolts holding the coil to the engine or spark plug. On coil-on-plug designs, the coil sits directly over the spark plug and is held down by one bolt. On older designs, the coil may be mounted on the engine block or firewall and held by two bolts. Keep the bolts in a small container so you don't lose them.
Lift the coil straight up and out of the engine bay. If it's stuck, wiggle it gently side to side—don't force it. Set it on a clean, dry surface. Wipe away any dirt or oil from the coil body with a clean rag, but do not spray it with water or cleaner. You're about to test its electrical properties, and moisture will give you a false reading.
Test primary resistance on the low-voltage side
Set your multimeter to the ohms (Ω) setting. On most multimeters, this is marked with the Greek letter omega. If your meter has multiple ohms ranges (like 200Ω, 2kΩ, 20kΩ), start with the 200Ω range for the primary test.
Look at the coil connector—the plastic housing where the wires plug in. You'll see two or more metal terminals inside. The primary terminals are the low-voltage terminals that connect to the battery and ignition system. On most coils, these are the larger terminals or the ones on the outer edge of the connector. Your owner's manual or a parts diagram will show you which terminals are primary.
Touch one multimeter probe to one primary terminal and the other probe to the other primary terminal. Hold them steady for two seconds. The meter should show a reading between 0.4 and 2 ohms. This range varies by manufacturer, so check the label on the coil itself or your owner's manual for the exact spec. If the meter shows zero, the windings are shorted. If it shows infinite resistance (often displayed as "OL" for overload), the windings are open and broken. Either reading means the coil is failed.
If the primary resistance is within spec, move on to the secondary test. If it's out of spec, the coil is bad and needs replacement.
Test secondary resistance on the high-voltage side
Switch your multimeter to the 20kΩ (20,000 ohms) range. The secondary terminals are the high-voltage terminals—usually the center terminal and one outer terminal on the connector. On some coils, the secondary is a single terminal that connects to the spark plug wire or coil cap.
Touch one probe to the secondary terminal and the other probe to the other secondary terminal (or to the coil body if there's only one secondary terminal). Hold steady for two seconds. The meter should show a reading between 6,000 and 30,000 ohms. Again, check your manual or the coil label for the exact range. A reading of zero or infinite resistance means the secondary windings are failed.
If both primary and secondary resistance are within spec, your coil is electrically sound. If one or both are out of spec, the coil needs replacement. Write down the readings so you have them for reference when you order a replacement or show them to a technician.
What to do if the coil passes the test but your engine still misfires
A coil that passes the resistance test is not the source of your misfire. The problem is somewhere else in the ignition or fuel system. Start by checking the spark plug itself—pull it out and look at the electrode gap and the condition of the ceramic insulator. A worn or fouled spark plug will cause the same symptoms as a bad coil. Replace the spark plug and see if the misfire goes away.
If the spark plug is good, check the coil connector and the wiring harness for corrosion, loose pins, or damaged insulation. A corroded connection can prevent voltage from reaching the coil, even if the coil itself is fine. Clean the connector with a wire brush and reconnect it firmly.
If the connector is clean and tight, the problem may be a fuel injector that's not firing, a vacuum leak, or a compression problem in that cylinder. These require more advanced diagnosis—a fuel injector can be tested with a stethoscope or a fuel pressure gauge, and compression can be tested with a compression tester. At this point, a shop with a scanner and the right tools is your best option.
Reinstall the coil or order a replacement
If your coil passed the resistance test, reinstall it in reverse order: bolt it back down, reconnect the electrical connector, and reconnect the battery negative terminal. Start the engine and confirm the misfire is gone. If it is, you've solved the problem without replacing the coil.
If the coil failed the test, order a replacement coil for your exact year, make, and model. Coils are not universal—a coil for a 2015 Honda Civic will not work in a 2015 Ford Focus. Get the part number from your owner's manual or from an auto parts store, and order online or pick one up locally. Installation is the reverse of removal: bolt it down, plug it in, and reconnect the battery.
Start the engine and confirm the check engine light is gone and the misfire has stopped. If the light comes back on after a few days of driving, the problem may be a second failed coil or a different issue in the ignition system. A shop scanner can read the specific fault code and point you in the right direction.
Frequently Asked Questions
Can I test a coil while it's still mounted on the engine?
Yes, but it's harder to get a good connection with the multimeter probes, and you risk accidentally touching a live terminal and getting shocked. Removing the coil takes ten minutes and gives you a safer, more reliable test. If you must test it in place, disconnect the battery first and let the engine cool completely.
What if my multimeter shows a reading that's close to the spec but not exactly on it?
Multimeters have a margin of error, usually around 5 percent. If your reading is within 5 to 10 percent of the spec, the coil is probably fine. If it's off by 20 percent or more, the coil is degrading and will likely fail soon. Replace it now rather than waiting for it to fail completely on the road.
Do I need to replace all the coils at once if one fails?
No. Replace only the coil that failed. However, if your vehicle has high mileage and multiple coils are original, consider replacing them all at once to avoid repeat failures. Coils typically last 80,000 to 150,000 miles depending on driving conditions and engine heat.
Can a bad coil damage my spark plugs or catalytic converter?
Yes. A failing coil causes misfires, which means unburned fuel enters the exhaust. This can foul spark plugs and damage the catalytic converter over time. The longer you drive on a bad coil, the more expensive the repair becomes. Test and replace it as soon as you notice symptoms.
What if I don't have a multimeter?
You can borrow one from a friend, rent one from an auto parts store (many rent tools for free or a small deposit), or buy an inexpensive digital multimeter for $15 to $25. It's worth having one in your toolbox for future tests. If you don't want to test it yourself, a shop can test the coil for you, though they'll usually charge a diagnostic fee.