What a coil does and why it fails

Your car's ignition coil converts low voltage from the battery into the high voltage needed to fire your spark plugs. Without it, your engine won't start or will run rough. A failing coil usually shows up as a misfire — the engine stumbles under acceleration, idles unevenly, or won't start at all. You might also see a check engine light.

Coils fail because of heat, moisture, and electrical stress. Modern cars have one coil per spark plug (or one coil pack per two plugs), so a single bad coil won't leave you stranded the way an older single coil would — but it will make the car undriveable until you fix it. Testing tells you whether the coil itself is the problem or whether you're chasing something else.

Key Takeaways

  • A multimeter set to resistance mode (ohms) can tell you if a coil's internal windings are open or shorted, which is the fastest way to rule it in or out.
  • Primary resistance (the low-voltage side) typically reads between 0.4 and 2 ohms; secondary resistance (the high-voltage side) usually reads between 6,000 and 15,000 ohms — check your owner's manual or the coil label for your car's exact specs.
  • A coil that reads infinity on the secondary side has an open circuit and is dead; one that reads zero or near-zero has shorted windings and must be replaced.
  • Visual inspection for cracks, corrosion, or a burnt smell can catch a failing coil before you need the multimeter.
  • If the coil tests good but the misfire persists, the problem is likely the spark plug, fuel injector, or compression — not the coil.

Locate your coil and get the specs

Open your hood and find the coil. On newer cars (2000 and later), coils sit directly on top of the spark plugs or are mounted on the valve cover with thick wires running to each plug. On older cars, there's usually one large coil mounted on the engine block or firewall with a single thick wire (the distributor wire) running to the distributor.

Write down the coil's part number or take a photo of the label. Look for the resistance specs printed on the coil itself — they're often stamped or stickered on the housing. If you can't find them on the coil, check your owner's manual or search the part number online. You need two numbers: primary resistance (measured in ohms) and secondary resistance (measured in kilohms or thousands of ohms). Without these, your multimeter readings won't mean anything.

Disconnect the coil safely

Turn off the engine and let it cool for at least five minutes. Disconnect the negative terminal of the battery — this prevents accidental spark or short circuits while you work. Locate the electrical connector on the coil (a plastic plug with two or four wires) and unplug it by pressing the tab or clip and pulling straight out.

If the coil is bolted to the engine, remove the bolt or bolts holding it in place. For coil packs mounted on the valve cover, you may need to remove a single bolt or clip. Don't force anything — if it's stuck, spray a little penetrating oil and wait a few minutes. Keep track of any bolts or clips in a small container so you don't lose them.

Test primary resistance with a multimeter

Set your multimeter to the resistance setting (marked with the omega symbol Ω). The dial should be on a low ohms range — usually 200 ohms or lower. Touch one probe to the positive terminal of the coil's primary connector and the other probe to the negative terminal. Read the number on the display.

Compare this reading to the spec on the coil. Primary resistance is usually between 0.4 and 2 ohms. If your reading is zero or very close to zero, the primary windings are shorted and the coil is bad. If your reading is infinity (the display shows "1" or "OL"), the primary circuit is open and the coil is bad. If the reading falls within the spec range, the primary side is good — move on to the secondary test.

Test secondary resistance with a multimeter

The secondary side is trickier because the resistance is much higher. Set your multimeter to a higher ohms range — usually 20,000 ohms or higher, depending on your meter. Some multimeters have a dedicated setting for high resistance; check your meter's manual if you're not sure.

Locate the secondary terminal on the coil — this is where the thick wire (or wires on a coil pack) connects. Touch one probe to the secondary terminal and the other to the coil's metal housing or to the negative primary terminal. Read the display. Secondary resistance typically ranges from 6,000 to 15,000 ohms, but check your spec sheet because this varies widely. If the reading is infinity, the secondary windings are open and the coil is bad. If the reading is zero or very close to zero, the windings are shorted and the coil is bad. If the reading is within spec, the coil is likely good.

Look for physical damage or corrosion

Before you reinstall the coil, inspect it visually. Look for cracks in the plastic housing, especially around the base where the connector plugs in. Moisture can seep through cracks and cause internal corrosion. Check the connector itself for green or white corrosion on the metal terminals — this blocks electrical flow and can mimic a bad coil.

Smell the coil. A burnt or acrid smell means the windings have overheated and failed internally, even if your resistance readings looked okay. If you see cracks, heavy corrosion, or smell burning, the coil needs to be replaced. If the connector is corroded but the coil housing is intact, you can sometimes clean the terminals with a wire brush or contact cleaner and try again — but if corrosion is heavy, replace the coil to avoid the same problem recurring.

What to do if the coil tests good

If your resistance readings are within spec and there's no visible damage, the coil is probably not the cause of your misfire. Reinstall it, reconnect the battery, and look elsewhere. A misfire with a good coil usually points to a bad spark plug, a clogged fuel injector, low fuel pressure, a vacuum leak, or a compression problem in that cylinder.

Start by swapping the spark plug in the misfiring cylinder with one from a different cylinder, then drive the car and see if the misfire moves to the new location. If it does, the plug was bad. If the misfire stays in the original cylinder, the problem is fuel delivery, compression, or the injector — not the ignition system. A compression test or fuel pressure test will narrow it down further, but those are beyond the scope of a coil check.

Frequently Asked Questions

Can I test a coil without removing it from the car?

Yes, if you can access the connector and the coil housing without removing bolts. Unplug the connector, set your multimeter to resistance mode, and touch the probes to the connector terminals. You won't be able to test the secondary side as easily without removing the coil, but a primary resistance reading can tell you if the coil is obviously shorted or open.

What if my multimeter doesn't have a high ohms setting?

Most basic multimeters max out around 20,000 ohms, which is enough for secondary resistance testing on most coils. If yours doesn't go that high, you can still test primary resistance. For secondary, you may need to borrow or rent a meter with a higher range, or take the coil to a shop for testing.

Do I need to replace the spark plug when I replace the coil?

Not necessarily. If the spark plug tested good (by swapping it with another cylinder), you can reuse it. However, if the coil failed because of a bad plug causing excessive arcing, replacing the plug will prevent the new coil from failing the same way. Check the plug's gap and condition before deciding.

Can a coil fail intermittently and still test good?

Yes. A coil that fails only when hot or under load may read fine on the bench. If your resistance readings are good but the misfire comes and goes, especially when the engine is warm or under acceleration, the coil may be failing thermally. In that case, replace it anyway — a bench test can't catch every failure mode.

How much does a replacement coil cost?

A single coil or coil pack typically costs between $40 and $150 depending on the car, with labor adding another $50 to $200 if you have a shop do it. Doing it yourself saves the labor cost and usually takes 10 to 20 minutes per coil once you know where it is.