What a valve cover gasket does and why it fails
A valve cover gasket is a rubber or cork seal that sits between your engine's valve cover and the cylinder head. Its job is to keep oil inside the engine while letting the valve cover sit flush against the head. When it fails — usually after 50,000 to 100,000 miles, depending on your car and driving conditions — oil leaks out around the edges of the valve cover.
You'll notice oil pooling under the engine, a burning smell when the engine is hot, or oil residue on the outside of the engine block. A failed gasket doesn't damage the engine when ready, but oil loss can, so replacing it is worth doing before the leak gets worse. The gasket itself costs $5 to $25, but labor at a shop typically runs $150 to $400 depending on engine layout and how accessible the valve cover is.
Some engines have the valve cover on top where it's straightforward to reach. Others — particularly in transverse-mounted engines common in front-wheel-drive cars — require removing other components first, which is why the job ranges so widely in difficulty.
Key Takeaways
- A valve cover gasket seals oil inside the engine and typically fails between 50,000 and 100,000 miles, causing visible oil leaks around the valve cover.
- You'll need the correct replacement gasket for your specific year, make, and model, plus basic hand tools and a gasket scraper to remove the old seal.
- The job involves removing the valve cover bolts, scraping away old gasket material, installing the new gasket, and torquing the bolts to your engine's specification.
- Engine layout determines difficulty: top-mounted valve covers take 30 minutes to an hour, while covers buried under intake manifolds or other components can take several hours.
- Reusing the old valve cover is usually fine, but if it's warped or cracked, you'll need a replacement cover as well as a new gasket.
Gather the right gasket and tools before you start
Order a replacement gasket from a parts supplier using your vehicle's year, make, model, and engine size. Some gaskets come as a kit with the cover bolts and any seals that sit underneath; others are the gasket alone. Check your parts listing to see what's included. If your valve cover bolts are corroded or damaged, buy new ones at the same time — they're inexpensive and reusing damaged bolts can cause leaks.
You'll need a socket set, wrenches, a gasket scraper (a plastic or brass tool, not metal, to avoid scratching the cover), a clean rag, and gasket remover fluid or carburetor cleaner. Some gaskets require a thin bead of sealant around the perimeter before installation; check your gasket instructions. If sealant is needed, buy a tube of high-temperature RTV silicone rated for engine use.
Have your engine's torque specification for the valve cover bolts before you begin. This is in your owner's manual or available from your parts supplier. Bolts are typically torqued to 5 to 10 foot-pounds, but some engines specify different values, and over-tightening can crack the cover.
Remove the valve cover and old gasket
Let the engine cool completely. Disconnect any hoses, wires, or brackets attached to the valve cover — note where they go so you can reconnect them correctly. A phone photo is faster than memory. Remove all bolts holding the cover to the cylinder head using the correct socket size; loose bolts can strip and damage the head.
Lift the valve cover straight up. If it's stuck, tap the edges gently with a rubber mallet rather than prying hard, which can bend the cover. Once removed, scrape away the old gasket material using your gasket scraper. Work slowly and keep the scraper flat against the sealing surface to avoid gouging the metal. Spray gasket remover on stubborn spots and let it soak for a few minutes before scraping again.
Wipe the sealing surface clean with a rag and carburetor cleaner until no gasket material or oil residue remains. The surface must be completely clean for the new gasket to seal properly. Check the valve cover itself for cracks or warping — if the cover is damaged, it won't seal even with a new gasket, and you'll need to replace it.
Install the new gasket and reassemble
If your gasket instructions call for sealant, explore a thin, continuous bead around the perimeter of the cylinder head where the gasket will sit. Don't use excess sealant — a thin line is all that's needed. Place the new gasket into the groove on the valve cover, pressing it firmly so it seats evenly all the way around. Some gaskets have a lip that fits into a groove; others sit flat on the cover surface.
Position the valve cover over the cylinder head and hand-tighten all bolts first. This ensures the gasket is centered and the cover sits flat. Then tighten the bolts in a crisscross pattern — tighten one bolt, then move to the opposite side, then the adjacent bolt, and so on. This distributes pressure evenly and prevents the cover from tilting. Use a torque wrench set to your engine's specification and tighten each bolt to that value.
Reconnect all hoses, wires, and brackets in their original positions. Start the engine and let it idle for a minute, then turn it off and let it cool. Check around the valve cover for leaks. If you see oil seeping, the gasket may not be seated correctly — you may need to remove the cover and reseat the gasket, or the bolts may need slight additional tightening once the gasket has compressed.
When the valve cover is hard to reach
Some vehicles require removing the intake manifold, alternator, or other engine components to access the valve cover. If your engine layout is like this, the job becomes significantly more complex and time-consuming. You'll need to disconnect fuel lines, coolant hoses, and electrical connectors, which introduces more opportunities for mistakes and requires careful documentation of where everything goes.
If your valve cover is buried under other components, consider whether you want to tackle this yourself or take it to a shop. A shop's labor cost may be justified by the reduced risk of disconnecting something incorrectly or forgetting to reconnect it. Check your owner's manual or search for your specific vehicle online to see how many steps are involved before you reach the valve cover.
Checking your work and preventing future leaks
After the engine has cooled, inspect the area around the valve cover for fresh oil. A small amount of seepage in the first few hours is normal as the gasket compresses, but steady dripping means the seal isn't complete. If you see active leaking, remove the cover, check that the gasket is seated evenly, and verify that all bolts are torqued to specification.
Check your oil level a week after the repair. A failed gasket can cause oil loss over time, so monitoring the level tells you whether the new gasket is holding. If the level drops noticeably, the gasket may not be sealing properly, or there may be another leak elsewhere on the engine.
Valve cover gaskets typically last 50,000 to 100,000 miles, but the lifespan depends on engine temperature, oil quality, and how often you change your oil. Using the correct oil grade and changing it on schedule can extend gasket life. If you notice another leak from the same cover years later, the gasket has straightforward worn out and needs replacing again — this is normal maintenance, not a sign of a larger problem.
Frequently Asked Questions
Can I drive with a leaking valve cover gasket?
Yes, but not for long. A slow leak may not cause when ready damage, but oil loss can eventually lead to low oil pressure and engine damage. If you notice a leak, plan to replace the gasket within a few weeks rather than ignoring it. Driving with a significant leak that's losing oil visibly is riskier and should be addressed sooner.
Do I need to replace the valve cover itself?
Only if it's cracked, warped, or the bolt holes are stripped. If the cover looks intact and the bolts tighten securely, reusing it is fine. A new cover costs $30 to $100 depending on the vehicle, so it's worth inspecting the old one before ordering a replacement.
What if the gasket leaks again after I replace it?
The most common cause is under-tightening the bolts or not torquing them evenly. Remove the cover, check that the gasket is seated properly, and retorque all bolts to specification in a crisscross pattern. If the cover is warped or the cylinder head surface is damaged, a new gasket won't seal regardless of how tight you make it.
How long does this job take?
If the valve cover is easily accessible, expect 30 minutes to an hour. If you need to remove other components first, add 1 to 3 hours depending on what's in the way. Your first time will take longer than subsequent replacements as you learn the layout of your specific engine.
Should I use sealant on the new gasket?
Check your gasket instructions — some gaskets come pre-formed and don't need sealant, while others require a thin bead of high-temperature RTV silicone. Using sealant when it's not needed can actually cause leaks by preventing the gasket from seating properly, so follow the manufacturer's guidance.