What motor mounts do and why they fail
Motor mounts are rubber-and-metal pieces bolted between your engine and the frame. They hold the engine in place while absorbing vibration so you don't feel the engine shaking through the steering wheel, pedals, and seat. A car typically has three to four mounts depending on the engine size and whether it's front-wheel or rear-wheel drive.
The rubber degrades over time from heat, oil exposure, and constant flexing. When a mount fails, the engine rocks excessively during acceleration or deceleration—you'll feel a hard clunk or see the engine visibly shift in the engine bay. A broken mount can also allow the engine to contact the frame or radiator, which causes real damage fast. Replacing mounts before they completely fail prevents that cascade.
The job is mechanical but not complicated if you have basic tools and patience. You'll need to support the engine weight safely, unbolt the old mounts, and install new ones. The time varies by which mount and your car's design—some take 30 minutes, others take two hours.
Key Takeaways
- Motor mounts hold the engine in place and absorb vibration; when they fail, the engine rocks visibly during acceleration and you feel hard clunks through the car.
- You must support the engine safely with a jack and wood block or engine hoist before unbolting any mount, because the engine will drop if you don't.
- Most mounts bolt to the engine on one side and the frame on the other; you unbolt both sides, slide the old mount out, and bolt the new one in the same way.
- The job takes 30 minutes to two hours depending on which mount and your car's layout; some mounts are buried under other components and require removal first.
- If you're uncomfortable supporting an engine or working under it, a shop can do this work for $200 to $600 per mount including parts and labor.
Gather tools and safety equipment before you start
You will need a floor jack rated for your car's weight, jack stands, a block of wood (4×4 or thicker), wrenches or sockets that fit your engine and frame bolts, and a way to support the engine while you work. The safest method is a engine hoist (a portable frame with a chain hoist), which you can rent from an auto parts store for $40 to $80 per day. If you don't have a hoist, you can use a floor jack with the wood block under the oil pan to spread the load, but this is riskier because the engine can slip.
Wear safety glasses and work gloves. Make sure the car is on level ground, the engine is cold, and the battery is disconnected at the negative terminal. Never work under a car supported only by a jack—always use jack stands as backup. If the engine is hot, wait at least an hour before starting.
Check your repair manual or a service database to identify which mounts your car has and where they bolt. Some mounts are straightforward to reach; others sit under the intake manifold, alternator, or other components that have to come off first. Knowing this before you start saves frustration.
Support the engine safely and remove the old mount
Raise the car on the floor jack until the wheels are off the ground, then place jack stands under the frame on both sides. Lower the car onto the stands. If you're using an engine hoist, position it over the engine and attach the chain to solid lifting points on the engine block—never to plastic covers or thin brackets. Raise the hoist just enough to take the weight off the mounts but not so much that you stretch hoses or wiring.
If you're using a floor jack instead, position the wood block under the oil pan (the flat metal pan at the bottom of the engine) and raise the jack slowly until the engine is supported but not lifted hard. The goal is to take pressure off the mount bolts so they come out easily.
Now unbolt the old mount. Most mounts have one bolt or set of bolts on the engine side and one or two on the frame side. Remove the frame bolts first, then the engine bolts. Slide the old mount out. If it's stuck, tap it gently with a rubber mallet—don't pry hard or you'll bend the frame.
Install the new mount in the same orientation
Check that the new mount matches the old one—same bolt pattern, same rubber thickness, same overall shape. Slide it into place and hand-tighten the engine bolts first, then the frame bolts. This lets you align the mount before you torque anything down.
Once the mount is positioned, tighten the bolts in a cross pattern if there are multiple bolts (like an X, not all one side first). Tighten to the torque specification in your manual—usually 35 to 50 foot-pounds for engine bolts and 40 to 60 for frame bolts, but this varies. If you don't have a torque wrench, tighten firmly but don't muscle it; over-tightening can crack the rubber or strip the bolts.
Lower the engine hoist or floor jack slowly while watching the mount. It should sit flat and centered. If it tilts or looks crooked, raise the engine again and loosen the bolts to re-center it.
Repeat for other failed mounts if necessary
If you're replacing more than one mount, repeat the process for each one. You can do them one at a time without fully lowering the engine between mounts, which saves time. However, never remove all mounts at once—always keep at least one supporting the engine weight.
Some cars have a transmission mount or rear engine mount that's harder to access. If you're replacing those, you may need to remove the transmission crossmember or exhaust components first. Check your manual for the exact sequence. If the job requires removing major components, this is a good point to stop and take the car to a shop, because the complexity and risk jump significantly.
Lower the engine and reconnect everything
Once all new mounts are installed and torqued, lower the engine hoist or floor jack completely. The engine should settle smoothly into the mounts without rocking or tilting. Reconnect the battery negative terminal. Start the engine and listen for clunks or vibration—the engine should run smoothly without the hard rocking you felt before.
Raise the car on the floor jack again and remove the jack stands, then lower the car to the ground. Take the car for a short test drive on a quiet road, accelerating and decelerating firmly to feel whether the mounts are working. You should feel smooth acceleration without the engine shifting visibly or clunking.
When to take the car to a shop instead
If the old mount is seized or the bolts are stripped, or if you're uncomfortable supporting an engine, a shop is the right choice. Shops have lifts, hoists, and experience with stuck bolts and unusual layouts. The cost is typically $200 to $600 per mount including parts and labor, depending on which mount and how long it takes to access. A single front mount might be $250; a rear or transmission mount might be $400 to $600.
If you damage the engine pan, frame, or wiring while working, the repair bill grows quickly. If you're unsure at any point, stop and ask a mechanic. A 30-minute phone call is cheaper than a mistake.
Frequently Asked Questions
Can I drive the car with a broken motor mount?
Yes, but not safely for long. A broken mount lets the engine rock and shift, which can damage the radiator, hoses, or wiring. It also makes the car harder to control during hard acceleration. Drive carefully to a shop or parts store to get the replacement, but don't ignore it.
How do I know which mount is broken?
Accelerate hard in an empty parking lot and feel which direction the engine rocks. If it rocks forward, the front mount is likely broken. If it rocks side to side, a side mount is broken. If it rocks backward, the rear mount is broken. You can also look in the engine bay while someone revs the engine—a broken mount will show visible movement.
Do I need to replace all mounts at once?
No, only the ones that are actually broken. However, if the car is old and all mounts look cracked or soft, replacing them all at once saves labor because the engine is already supported. New mounts cost $30 to $150 each depending on the car, so the parts cost is usually less than the labor.
What if the bolts won't come out?
Spray penetrating oil (like PB Blaster or Liquid Wrench) on the bolt and let it soak for 15 to 30 minutes. Tap the bolt gently with a hammer to break corrosion loose, then try again. If it still won't budge, stop—forcing it risks stripping the hole or breaking the bolt. A shop can remove stuck bolts with an impact wrench or by drilling them out if necessary.
Can a bad motor mount damage the engine?
Yes. A severely broken mount can let the engine contact the radiator, frame, or transmission, which causes coolant leaks, frame damage, or transmission problems. Catching and replacing a mount early prevents this cascade of damage.