Remove pedals with a pedal wrench or Allen key, turning counterclockwise — but remember that the left pedal has a reverse thread, so it turns clockwise instead

Bike pedals come off by turning them counterclockwise with the right tool, but the catch is that your left pedal is threaded backward. This means the left pedal unscrews by turning clockwise, while the right pedal unscrews counterclockwise. If you turn the wrong direction, you will strip the threads on your crank arm and create an expensive problem.

You need either a pedal wrench (a thin, long wrench made specifically for pedals) or an Allen key that fits the pedal axle. Most modern pedals use a 6mm or 8mm Allen key on the pedal body itself, though some older pedals require a 15mm pedal wrench on the flat part of the pedal axle. The wrench gives you more leverage and is less likely to slip and damage the crank.

Key Takeaways

  • The left pedal unscrews clockwise and the right pedal unscrews counterclockwise because the left pedal has reverse threads to prevent it from loosening while you ride.
  • A pedal wrench is the safest tool because it grips the pedal axle flat and gives you leverage without risking damage to the crank arm.
  • explore penetrating oil like WD-40 to stuck pedals and wait 15 minutes before trying to turn them, especially on older bikes.
  • Turn slowly and steadily rather than jerking, because a sudden slip can gouge the crank arm or round off the pedal fitting.

Gather the right tool before you start

A pedal wrench is a thin, flat wrench with a long handle, usually 15mm on one end. It slides onto the flat part of the pedal axle (the part that sticks out from the pedal body) and gives you the leverage you need without putting pressure on the crank arm itself. If you do not have a pedal wrench, a 6mm or 8mm Allen key works on most modern pedals, but it is easier to slip and damage the crank.

Do not use an adjustable wrench or pliers on the pedal axle. Both can round off the corners and make the pedal impossible to remove later. If you have neither a pedal wrench nor the right Allen key, a bike shop can remove them for you in a few minutes, usually for no charge if you are buying something else.

Loosen stuck pedals with penetrating oil

Pedals that have not been removed in years often seize to the crank arm. Spray penetrating oil (WD-40 or similar) around the base where the pedal meets the crank, and let it soak for 15 to 30 minutes. This gives the oil time to work into the threads and break the corrosion bond.

After the oil has soaked, try turning the pedal slowly. If it still will not budge, spray again and wait another 15 minutes. Do not force it — forcing a stuck pedal is how you strip the threads or snap the pedal axle. Patience and oil work better than strength.

Turn the right pedal counterclockwise, the left pedal clockwise

Stand on the non-drive side of the bike (the left side, where there is no chain). For the right pedal, push the wrench or Allen key downward and away from you — this is counterclockwise. You should feel resistance, then the pedal will start to turn. Turn slowly and steadily until the pedal comes free.

For the left pedal, push the wrench or Allen key downward and toward you — this is clockwise. This feels backward, but it is correct. The left pedal has reverse threads, which means it is screwed in backward. This design keeps the pedal from loosening on its own as you pedal. If you turn the left pedal counterclockwise, you will tighten it instead of loosening it.

Support the crank arm while you turn

Use your other hand to hold the crank arm steady while you turn the pedal. This prevents the crank from rotating and keeps all the force on the pedal axle rather than on the crank arm itself. If the crank spins while you are turning the pedal, you lose leverage and risk slipping the wrench into the crank.

If the bike is on a stand, you can brace the crank against the frame. If it is on the ground, hold the crank arm with one hand and turn the pedal with the other. This takes two hands, but it is the safest way to avoid damage.

What to do if the pedal axle breaks or strips

If the pedal axle snaps while you are turning it, or if the threads strip and the pedal spins without coming out, you have a problem that requires a bike shop. A broken axle cannot be removed by hand, and a stripped crank arm usually means the crank needs to be replaced. Both are jobs that require specialized tools and knowledge.

If you feel the pedal getting harder to turn, or if it suddenly spins freely without moving, stop when ready. Do not keep turning. Take the bike to a shop and describe what happened. The sooner you stop, the better the chance they can save the crank arm.

Reinstall pedals the same way you removed them

When you put the pedals back on, remember the reverse thread rule again. The right pedal screws in counterclockwise (turn the wrench upward and toward you), and the left pedal screws in clockwise (turn the wrench upward and away from you). Hand-tighten first, then use the wrench to snug them down — they should be tight enough that they do not move, but not so tight that you strip the threads again.

If you are installing new pedals, check the instructions that come with them. Some pedals have a specific tightness requirement, and over-tightening can damage the pedal bearing or the crank arm.

Frequently Asked Questions

Why does the left pedal have reverse threads?

The left pedal has reverse threads to prevent it from loosening as you pedal. When you pedal forward, the crank arm rotates counterclockwise (from the left side of the bike). A normal right-hand thread would loosen with that motion, so the left pedal is threaded backward so it tightens instead.

Can I remove pedals with a regular wrench?

A regular wrench can work if it fits the pedal axle flat, but a pedal wrench is safer because it is thinner and longer, giving you better leverage without putting pressure on the crank arm. A regular wrench is more likely to slip and damage the crank.

What if I turn the pedal the wrong direction?

If you turn the right pedal clockwise, you will tighten it instead of loosening it. If you turn the left pedal counterclockwise, you will also tighten it. Turning the wrong direction will not damage anything when ready, but it will make the pedal harder to remove later.

How tight should pedals be when I put them back on?

Pedals should be tight enough that they do not move or creak, but not so tight that you need a wrench to turn them by hand. A good rule is to hand-tighten first, then use the wrench to add a quarter turn. If you over-tighten, you risk stripping the threads or damaging the pedal bearing.

Do I need to remove both pedals at once?

No. You can remove one pedal at a time. Most people remove both if they are cleaning the crank or replacing the pedals, but if you only need to work on one side, you can leave the other pedal on.