The pedal attaches to the crank arm through a threaded spindle

A bike pedal connects to your bike through a metal rod called the spindle, which screws into the crank arm — the lever that extends from the center of your bike's drivetrain. The spindle is the shaft that runs through the pedal's body and threads into a hole on the crank arm. When you push the pedal, you're pushing on the pedal body, which rotates around the spindle, and that rotation transfers through the crank arm to turn the chainring and move your bike forward.

The connection is straightforward but precise. The spindle has threads cut into it, and the crank arm has matching threads drilled into its end. The spindle screws in by hand or with a wrench, and once tight, it holds the pedal firmly in place. The pedal can rotate freely around the spindle because the spindle itself is held stationary by the crank arm — only the pedal body spins.

Key Takeaways

  • The spindle is a threaded metal rod that screws into the crank arm and holds the pedal body in place while allowing it to rotate.
  • Pedals are handed — the right pedal has right-hand threads and the left pedal has left-hand threads — so you cannot install them backward.
  • Pedal spindles come in different lengths and diameters, and you must match the spindle to your crank arm's thread size or the pedal will not fit.
  • A loose pedal will creak or click while you ride, and tightening it with a pedal wrench or Allen key usually stops the noise.

Why pedals are handed and how to install them correctly

Bike pedals are handed, meaning the right pedal and left pedal are different and cannot be swapped. The right pedal has standard right-hand threads that tighten when you turn it clockwise. The left pedal has reverse threads that tighten when you turn it counterclockwise. This design prevents the pedal from unscrewing as you pedal — the rotation of the crank arm naturally tightens the pedal rather than loosening it.

When you install a pedal, you need to turn it in the direction that tightens it for that side. If you try to install a right pedal on the left crank arm, you will strip the threads because you are turning it the wrong way. Most pedals are clearly marked with an R or L, and the spindle itself is usually stamped with the direction to tighten. If you are unsure, the pedal should thread in smoothly with light hand pressure — if it feels stiff or gritty, you are turning it the wrong direction and should stop when ready.

Spindle diameter and thread size must match your crank arm

Pedal spindles come in different diameters and thread pitches, and the spindle on your pedal must match the hole drilled into your crank arm. The most common size on modern bikes is 9/16 inch, which fits most road bikes and mountain bikes made in the last 20 years. Older bikes and some children's bikes use 1/2 inch spindles instead. If you buy a pedal with the wrong spindle size, it will not thread into your crank arm at all, or it will thread in loosely and fall out.

Before you buy replacement pedals, check what size your current pedals are — the spindle diameter is usually printed on the pedal body or stamped into the spindle itself. If you cannot read it, measure the spindle with calipers or take a photo to a bike shop. Mixing spindle sizes is not possible, so getting the right size the first time saves you a return trip.

How the pedal body rotates around the spindle

Inside the pedal body is a bearing — usually a cartridge bearing or loose ball bearings — that lets the pedal rotate smoothly around the spindle. The spindle passes through the center of this bearing, and the bearing itself is pressed or screwed into the pedal body. As you push down on the pedal, the pedal body spins around the stationary spindle, and the bearing reduces friction so the pedal moves freely.

Over time, bearings wear out and the pedal becomes loose or creaky. When this happens, you can sometimes tighten the bearing by turning an adjustment cone on the spindle, but many modern pedals use sealed cartridge bearings that cannot be adjusted — you have to replace the entire pedal. A pedal that spins freely with no grinding noise has healthy bearings. A pedal that feels rough or has play when you wiggle it side to side needs attention.

Tools and steps to install or remove a pedal

You need a pedal wrench or a 15 mm open-end wrench to install or remove pedals. Some pedals also accept a 6 mm or 8 mm Allen key, depending on the design. The wrench fits onto a flat section of the spindle, usually near where it enters the pedal body. Position the wrench so it points toward the rear of the bike, then turn it in the direction that tightens the pedal for that side — clockwise for the right pedal, counterclockwise for the left pedal.

To remove a pedal, turn the wrench in the opposite direction. The pedal should come free with steady pressure — do not use a cheater bar or hammer unless the pedal is severely stuck, because you risk stripping the threads in the crank arm. Once the pedal is loose, you can unscrew it by hand. When installing a new pedal, thread it in by hand first until it is snug, then use the wrench to tighten it fully. A properly installed pedal should not move or creak when you push on it.

Why pedals creak and how to fix it

A creaking pedal is almost always a loose spindle. As you pedal, the pedal body rocks slightly on the spindle, and this movement creates the creak. The fix is straightforward: tighten the pedal with a wrench. Loosen the pedal slightly, then tighten it again firmly — do not over-tighten, because you can crack the pedal body or strip the crank arm threads. The pedal should be tight enough that it does not move when you push on it, but not so tight that you need to strain with the wrench.

If tightening does not stop the creak, the bearing inside the pedal may be worn. Wiggle the pedal side to side while holding the crank arm — if the pedal moves, the bearing has play and the pedal needs to be replaced. A creak that continues after tightening usually means the bearing is damaged and cannot be repaired.

Frequently Asked Questions

Can I use the same pedal on both sides of the bike?

No. Right and left pedals have different thread directions, so a right pedal will not thread into the left crank arm correctly. Always check the R or L marking on the pedal before installing it. Using the wrong pedal will strip the threads in your crank arm.

What happens if I over-tighten a pedal?

Over-tightening can crack the pedal body, strip the threads in the crank arm, or both. Tighten until the pedal is snug and does not move, then stop. If the pedal still creaks after a firm tightening, the bearing is likely worn and the pedal should be replaced rather than tightened further.

How do I know if my pedal spindle is 9/16 inch or 1/2 inch?

Check the pedal body or spindle for a size marking — most pedals are stamped with the spindle diameter. If you cannot find a marking, measure the spindle with calipers or bring the pedal to a bike shop and they can measure it for you in seconds.

Can I replace just one pedal if the other is still good?

Yes, you can replace a single pedal. Make sure the new pedal has the same spindle size and is marked for the correct side (R or L). You do not need to replace both pedals unless both are damaged or worn.