What happens when you replace a motor mount

A motor mount is a rubber-and-metal bracket that holds your engine in place and absorbs vibration as it runs. When one fails, you'll feel excessive shaking in the steering wheel, gear shift, or floor — especially when you accelerate or shift into gear. Replacing it means removing the engine weight from that mount, unbolting the old one, and installing a new bracket in its place.

The job itself is straightforward in concept but varies wildly in difficulty depending on which mount has failed and your vehicle's layout. Some mounts take 30 minutes; others require dropping the engine subframe or removing the transmission, which can take a full day. This guide walks you through what the work involves, what tools you'll need, and the point at which a DIY attempt becomes more expensive than a shop visit.

Key Takeaways

  • Motor mounts are rubber-and-metal brackets that hold your engine in place; a failed mount causes shaking during acceleration or gear shifts.
  • Replacing a mount requires supporting the engine weight, unbolting the old bracket, and installing a new one — the time required depends entirely on which mount has failed and your vehicle's design.
  • Front mounts are usually accessible; rear and side mounts often require removing other components like the transmission, subframe, or exhaust.
  • You'll need a jack, jack stands, basic hand tools, and a way to support the engine safely — a transmission jack or engine hoist makes the job much faster.
  • If the mount is buried under the transmission or requires engine removal, a shop visit is usually cheaper than renting specialty equipment.

Identifying which mount has failed

Your vehicle has between three and five motor mounts depending on engine size and design. The most common failure points are the front mount (closest to the radiator) and the rear mount (near the transmission). Side mounts on the left and right also wear out, though less frequently.

To narrow down which one is bad, start the engine in park and have someone watch the engine from the side while you rev it gently. Excessive movement in one direction points to a failed mount on the opposite side — if the engine rocks forward, the rear mount is likely the problem. You can also feel for movement by placing your hand on the engine block (away from moving parts) while someone revs the engine in neutral.

Once you know which mount is failing, look up your vehicle's service manual or a repair guide specific to your year, make, and model. This tells you whether that particular mount is a 30-minute job or a 4-hour job. If the mount is buried under the transmission or requires engine removal, a shop visit becomes the practical choice.

Tools and equipment you'll need

At minimum, you need a floor jack, jack stands rated for your vehicle's weight, basic hand tools (wrenches and sockets in the sizes your engine uses), and a way to safely support the engine while you work. A transmission jack or engine hoist is ideal; a block of wood and a second jack can work in a pinch, but it's slower and riskier.

You'll also need new fasteners — bolts that hold the mount to the engine and frame often cannot be reused after removal. Check your service manual for the correct grade and size. A torque wrench is essential; motor mount bolts are typically torqued to between 35 and 75 foot-pounds depending on the bolt, and under-tightening can cause the mount to fail again within weeks.

If the mount is welded or bolted to a bracket that's also worn, you may need to replace the entire bracket assembly rather than just the rubber insert. This costs more but is sometimes the only option. Your parts supplier can tell you whether the mount is sold separately or as part of a larger assembly.

The basic replacement process

Start by disconnecting the negative battery terminal to prevent accidental short circuits. Raise the vehicle on a jack and find it with jack stands under the frame — never work under a vehicle supported only by a jack. Remove the wheel well liner or splash guard if it blocks access to the mount.

Position your transmission jack or engine hoist under the engine oil pan (use a block of wood to distribute pressure) and raise it just enough to take the engine's weight off the mount — you want the engine to lift slightly, not dramatically. This is the critical step: if you don't support the engine properly, the mount will not come free, and you risk dropping the engine.

Unbolt the mount from the engine block and the frame or subframe. The old mount will come free once both sides are unbolted. Install the new mount, hand-tighten the bolts first, then torque them to the specification in your service manual. Lower the engine back onto the mount slowly, watching to make sure it settles evenly. Remove the jack and reinstall any components you removed for access.

When a front mount is accessible versus buried

Front mounts are usually the easiest to replace because they sit between the engine and radiator with minimal obstruction. You can often reach them by removing the wheel well liner and working from underneath, or by removing the radiator fan shroud from above. These jobs typically take 45 minutes to an hour.

Rear mounts are another story. On many vehicles, the rear mount bolts to the transmission or sits directly behind it, which means you may need to remove the transmission to access it. Some designs allow you to unbolt the mount from the frame side without removing the transmission, but you'll still need to support the engine weight and may need to remove the exhaust or other components for clearance.

Side mounts vary by design. Some are accessible from the wheel well; others require removing the engine oil pan, transmission pan, or both. Before you start, consult a repair manual or video specific to your vehicle. If the mount requires removing the transmission, subframe, or engine oil pan, the labor cost at a shop is usually less than the cost of renting specialty tools and the time investment.

Common mistakes that cost time and money

The most frequent error is not supporting the engine properly before unbolting the mount. If the engine shifts or drops while you're working, you can damage the engine block, crack the oil pan, or pinch hoses and wiring. Always use a jack rated for your vehicle's weight and position it under a solid part of the engine — the oil pan alone is not strong enough.

Another mistake is reusing old fasteners. Motor mount bolts are often torque-to-yield bolts, which means they stretch slightly during installation and cannot be safely reused. Using old bolts can cause the mount to loosen within a few hundred miles. Buy new bolts and washers as part of your parts kit.

Under-torquing the new bolts is equally common. A mount that's hand-tightened or torqued to the wrong specification will fail again quickly. Use a torque wrench and follow your service manual exactly. If you don't own a torque wrench, a shop visit is the better choice — the cost of a wrench plus your time is often more than a mechanic's labor.

Deciding between DIY and a shop visit

If the failed mount is a front mount on a vehicle with good access, and you have a transmission jack or engine hoist available, a DIY replacement is realistic for someone with basic mechanical skills. Budget two to three hours and have a helper on hand.

If the mount is rear, side, or requires removing the transmission, subframe, or engine oil pan, a shop visit is usually the better choice. Renting an engine hoist costs $40 to $80 per day, and the job may take longer than you expect if fasteners are seized or components don't fit back together smoothly. A shop will charge $200 to $600 in labor depending on the mount location, which is often less than your time plus rental costs.

Motor mount replacement at a shop typically costs $300 to $800 total, including parts and labor. A single front mount might be $200 to $400; a rear mount or multiple mounts can run $600 to $1,200. Get a quote before you commit, and ask whether the shop will replace all mounts at once if multiple ones are worn — doing them together saves labor time.

Frequently Asked Questions

Can I drive with a bad motor mount?

Yes, but not safely for long. A failed mount causes excessive engine movement, which can damage hoses, wiring, and the engine block itself. The shaking also makes the vehicle harder to control during acceleration. Have it replaced within a few days of noticing symptoms.

How long does a motor mount last?

Motor mounts typically last 5 to 10 years or 100,000 to 150,000 miles. They wear faster if you drive aggressively, tow frequently, or live in a very hot climate where rubber degrades quicker. Regular engine oil changes don't directly affect mount life, but a well-maintained engine puts less stress on the mounts.

Do I need to replace all motor mounts at once?

No, but if two or more are worn, replacing them together saves labor time and money. A shop can inspect all mounts while the vehicle is on a lift and recommend which ones need replacement. If only one is clearly failed, you can replace just that one.

What's the difference between OEM and aftermarket motor mounts?

OEM (original equipment manufacturer) mounts are made by your vehicle's manufacturer and typically last longer but cost more. Aftermarket mounts are cheaper but vary in quality — some last as long as OEM parts, while others fail within a few years. Mid-range aftermarket brands usually offer the best value.

Will replacing a motor mount fix my check engine light?

Only if the light is specifically for a motor mount sensor. Some vehicles have sensors that detect excessive engine movement and trigger a code. A failed mount can cause this code, but other problems like a bad oxygen sensor will not be fixed by replacing the mount. Have the code read before you assume the mount is the cause.