Find the bonnet release lever inside your car
The bonnet release lever is a handle or knob located inside your vehicle, almost always on the driver's side. In most cars made in the last 20 years, it sits low on the dashboard or on the left side of the steering column, near your knee. Pull it toward you with moderate force — it should click or pop slightly as the bonnet unlatches.
If you cannot find an interior lever, check your owner's manual for the exact location in your model. Some older vehicles or specialty cars may have the release in a different spot, and a few very old cars use a manual latch under the bonnet itself with no interior release at all.
Key Takeaways
- The bonnet release lever is inside the car on the driver's side, usually near the steering column or lower dashboard.
- Pull the interior lever first, then go to the front of the car and lift the bonnet to release the safety catch.
- The safety catch is a small metal rod or lever under the bonnet's center or side that prevents it from flying open while driving.
- Push or lift the safety catch depending on your car's design, then raise the bonnet fully and prop it open with the support rod.
- If the bonnet is stuck, do not force it — check for ice buildup, corrosion, or a broken cable, and consult your manual or a mechanic.
Walk to the front of the car and locate the safety catch
After pulling the interior release, go to the front of your car. You will see the bonnet is now slightly ajar. Slide your fingers under the edge of the bonnet at the center or toward one side — the exact location varies by manufacturer. You are looking for a small safety catch, which is a metal rod, lever, or hook that holds the bonnet closed as a backup.
The safety catch prevents the bonnet from flying open while you are driving if the main latch fails. It is a deliberate second lock, not a sign something is wrong. Once you find it, you will see it is blocking the bonnet from opening all the way.
Release the safety catch and lift the bonnet
Push or lift the safety catch, depending on your car's design. Most catches require a gentle push to one side or a small upward lift. Once it moves, the bonnet will be free to open. Lift the bonnet slowly and steadily until it reaches its full height.
As you lift, you may hear a slight creak or pop — this is normal. The bonnet is heavier than it looks, so use both hands if needed. Do not let it slam down on your head or fingers.
find the bonnet with the support rod
Most bonnets come with a metal support rod (also called a prop rod or strut) that holds it open safely. This rod is usually stored in a small clip or holder on the underside of the bonnet or on the inside of the engine bay. Locate it, remove it from its holder, and insert the end into the hole or bracket on the bonnet frame or the engine bay wall.
The support rod keeps the bonnet from falling on you while you work. Make sure it is fully seated in both the bonnet and the engine bay — it should not wobble or feel loose. If your car does not have a support rod, some models use a hydraulic strut that holds the bonnet open automatically.
What to do if the bonnet will not open
If the bonnet is stuck after you pull the interior release, do not force it. Forcing a stuck bonnet can break the cable or latch mechanism, which is expensive to repair. Instead, check for ice buildup around the bonnet's edges in winter — warm water or a heat gun can help melt it.
Corrosion around the latch or a broken cable are also common causes. If the bonnet still will not budge, consult your owner's manual for a manual release procedure (some cars have a backup latch you can access from underneath), or take the car to a mechanic. Trying to pry it open with tools risks damaging the bonnet's paint and frame.
Closing the bonnet safely
To close the bonnet, first remove the support rod and return it to its holder. Lower the bonnet slowly by hand until it is about 12 inches from closed, then let it drop the rest of the way. It should latch with a solid click. Do not slam it down — the latch will catch it, but slamming can damage the hinges over time.
Once closed, pull the interior release lever again to make sure the bonnet is fully latched. If it pops open slightly, the latch did not catch properly. Close it again and listen for a definite click before you drive.
Frequently Asked Questions
Why does my bonnet have two latches?
The interior release and the safety catch work together as a safety system. The interior release is the main latch; the safety catch is a backup that prevents the bonnet from opening if the main latch fails while you are driving. Both must be released before the bonnet will open fully.
What if I cannot find the support rod?
Check the underside of the bonnet near the center, or look inside the engine bay along the top edge. Some cars store the rod in a clip on the driver's side or passenger's side of the engine bay. If it is missing, you can buy a replacement from a parts supplier or your dealership — do not work under an open bonnet without one.
Is it normal for the bonnet to be hard to close?
A bonnet should close with gentle pressure and latch with a click. If it requires a lot of force or does not latch properly, the latch mechanism may be misaligned or dirty. Clean the latch area with a dry cloth and try again. If the problem persists, have a mechanic check the alignment.
Can I open the bonnet if the car is running?
Yes, you can open the bonnet while the engine is running, but it is safer to turn the engine off first. A running engine is hot and can burn you, and you have a better view of the engine bay with the engine off. Always wait a few minutes after turning off the engine before opening the bonnet if you have been driving.