Finding and Using the Bonnet Release Lever

The bonnet release on a Honda CR-V is a two-step process: pull the interior lever first, then push the safety catch under the bonnet. The interior lever is located on the left side of the dashboard, below the steering wheel, near the floor. It's a small black handle with a bonnet symbol on it. Pull it toward you firmly — you'll hear a click as the bonnet unlatches.

After pulling the interior lever, walk to the front of the vehicle. You'll see a small metal safety catch in the center of the bonnet's underside, just above the grille. Push this catch to the side (usually to the right) and the bonnet will swing open. The bonnet is held up by a hydraulic strut on each side, so it won't slam shut on you once it's released.

If the interior lever doesn't click or feels stuck, do not force it. A stuck cable is common in older CR-Vs, and pulling too hard can snap it. Move on to the troubleshooting section below.

Key Takeaways

  • The bonnet release lever is on the left side of the dashboard below the steering wheel and has a bonnet symbol printed on it.
  • After pulling the interior lever, push the safety catch under the bonnet to the side to fully release it.
  • Hydraulic struts hold the bonnet open, so you don't need to prop it with a stick or your hand.
  • If the interior lever is stuck or won't click, the release cable may be damaged and will need replacement by a mechanic.

What to Do If the Interior Lever Is Stuck

A stuck bonnet lever usually means the release cable has corroded or come loose inside the door panel. This is especially common in CR-Vs over ten years old or in areas with high humidity or salt air. Do not yank the lever repeatedly — this will snap the cable and make the problem worse.

Your options are limited without opening the bonnet. You can try spraying penetrating oil (like WD-40) around the lever mechanism and letting it sit for an hour, then gently working the lever back and forth. If that doesn't free it, you'll need a mechanic to access the cable from inside the door panel and either free it or replace it. Replacement usually takes under an hour and costs between $150 and $300 depending on your location and whether the cable snapped or just seized.

What to Do If the Safety Catch Won't Release

The safety catch under the bonnet can jam if dirt or debris builds up around it, or if the catch itself has rusted. If you've pulled the interior lever and heard it click, but pushing the safety catch does nothing, try spraying penetrating oil around the catch and waiting a few minutes. Then gently wiggle the catch side to side while pushing it.

If the catch is visibly rusted or broken, or if oil doesn't free it, the catch mechanism will need replacement. This is a small part that costs $20 to $50, but a mechanic will need to remove the bonnet to access it — adding labor time. If you're comfortable working under the bonnet yourself, you can order the part online and install it with basic hand tools.

Bonnet Won't Stay Open or Closes on Its Own

If the bonnet opens but the hydraulic struts are weak, it may sag or close on its own. This is a safety issue because the bonnet can fall on your head or hands while you're working. The struts are sealed units and cannot be repaired — they must be replaced as a pair.

Replacement struts cost $30 to $80 per pair and take about 30 minutes to install. You can do this yourself with basic tools: unbolt the old struts from the bonnet and frame, and bolt the new ones in the same position. If you're not comfortable working overhead, a mechanic can do it quickly and inexpensively. Do not prop the bonnet open with a stick or your hand while the struts are weak — use a proper bonnet prop or have the struts replaced first.

Bonnet Won't Close or Latch Properly

If the bonnet closes but won't latch, or if it pops open while driving, the latch mechanism or the safety catch may be misaligned. Start by checking that nothing is blocking the latch — leaves, dirt, or a loose hose can prevent a clean close. Clean around the latch and try again.

If the bonnet still won't latch, the latch or catch may be bent or out of alignment. This usually happens after a minor collision or if someone has forced the bonnet closed. A mechanic can realign or replace the latch in under an hour. Driving with an unlatched bonnet is dangerous — the bonnet can fly open at highway speeds and block your vision or damage the windscreen.

Bonnet Release Cable Replacement

If the interior lever pulls freely but nothing happens, or if the lever snapped, the release cable has likely broken. The cable runs from the lever through the door frame and down to the latch mechanism. Replacement requires removing the door panel and running a new cable through the same path.

This is a job for a mechanic unless you have experience with door panel removal. The cable itself costs $20 to $40, but labor typically runs $100 to $200. Some mechanics offer a combined price of $150 to $300 for the part and installation. If you're handy, you can order the cable online and watch a CR-V-specific video guide, but the door panel removal is the hardest part and straightforward to damage if you're not careful.

Frequently Asked Questions

Can I open the bonnet from outside if the interior lever is broken?

Not easily. The safety catch is designed to prevent accidental opening, so it's only accessible from under the bonnet. If the interior lever is broken, you'll need a mechanic to access it from inside the door panel or to remove the bonnet entirely.

Is it normal for the bonnet to be hard to close?

No. The bonnet should close with gentle pressure — you should not have to slam it or push hard. If it's difficult to close, the latch or safety catch may be misaligned or dirty. Clean the latch area first, and if that doesn't help, have a mechanic check the alignment.

What if the bonnet opens while I'm driving?

Pull over when ready and stop safely. Do not continue driving — an open bonnet can block your vision or fly off and hit other vehicles. Check that the bonnet is fully latched and the safety catch is engaged. If it opens again, do not drive the vehicle; have it towed to a mechanic to check the latch and safety catch.

Do I need to replace both hydraulic struts at the same time?

Yes. The struts work as a pair, and if one is weak, the other is likely to fail soon. Replacing both at once prevents the bonnet from sagging unevenly and ensures it stays open safely while you work.

How often should I lubricate the bonnet release mechanism?

Once a year is reasonable, especially if you live in a humid or coastal area. Spray a small amount of penetrating oil around the interior lever and the safety catch, and work the lever a few times to distribute the oil. This helps prevent rust and corrosion from seizing the mechanism.