What a 3D-printed airbox block off does and why GT86 owners use them
An airbox block off plate is a solid insert that closes off the secondary air intake port on your GT86's airbox. The stock airbox has two openings: one for the main intake and one for a secondary port that draws cooler air during certain engine conditions. A block off plate seals the secondary port completely, forcing all intake air through a single path.
GT86 owners 3D print these plates instead of buying them because the part is straightforward geometry with no moving pieces, making it ideal for home fabrication. The printed version costs under $5 in material versus $30–$60 for a commercial part, and you control the fit and finish. Most owners report that printing one takes 8–12 hours on a standard FDM printer.
The stated reason for blocking off the secondary port is to improve intake flow consistency and potentially support tuning changes. Whether this produces measurable performance gains on a stock or lightly modified GT86 is debated among owners—some report smoother throttle response, others notice no difference. The modification is reversible and does not affect warranty coverage on other engine components.
Key Takeaways
- A 3D-printed airbox block off plate seals the secondary intake port on your GT86 airbox with a solid insert that you can print at home or through a service.
- The part requires PETG or ABS filament rated for under-hood temperatures, not standard PLA, because engine bay heat will warp or soften the plastic.
- You will need the airbox removed from the engine bay to install the plate, which takes 15–30 minutes and requires no special tools beyond a screwdriver.
- Existing 3D models are available on Thingiverse and Printables, but you should test fit the printed part before final installation to check for interference with the airbox walls.
- The modification does not trigger check engine lights or affect emissions monitoring on stock GT86 models, though tuned vehicles may need a custom tune to prevent sensor confusion.
Choosing the right filament for under-hood temperatures
The filament you choose determines whether your block off plate survives engine bay heat or warps within weeks. PLA, the most common 3D printer filament, has a glass transition temperature around 60°C (140°F). Engine bays regularly exceed this, especially around the airbox location near the intake manifold. A PLA plate will soften, warp, or crack within a few heat cycles.
PETG is the practical choice for most GT86 owners. It handles sustained temperatures up to 80°C (176°F) without deforming, prints on standard FDM printers without special equipment, and costs only slightly more than PLA. Print it at 240–250°C nozzle temperature with a heated bed at 80°C for best layer adhesion.
ABS is more heat-resistant (glass transition around 105°C) but requires a heated chamber or enclosure to print without warping, and the fumes are stronger. Unless you already have ABS printing dialed in, PETG is the easier path. Some owners use nylon for maximum durability, but it absorbs moisture and requires a drying step before printing, adding complexity.
Print with 100% infill or at least 90% infill with a thick wall (4–6 perimeters). A hollow or sparse print will flex under pressure and may not seal the port completely.
Finding and preparing a 3D model for your GT86
The GT86 airbox block off plate is a straightforward part, and several community-designed models exist online. Search Thingiverse and Printables for "GT86 airbox block off" or "BRZ airbox block off"—the Subaru BRZ shares the same airbox design, so BRZ models work for GT86. Most models are free downloads under Creative Commons or open-source licenses.
Before you print, read the STL file and open it in your slicing software (Cura, PrusaSlicer, or Simplify3D). Rotate and position the part so the flat sealing face is parallel to the print bed—this ensures the surface that contacts the airbox is smooth and flat. Orient the part to minimize support material; most designs print well with minimal or no supports if positioned correctly.
Check the model dimensions against your airbox. The plate should be roughly 80–120 mm in diameter depending on the design. If the model seems significantly larger or smaller than expected, compare it to photos of the airbox port or measure your own airbox before printing. Some models are designed for specific airbox revisions, so verify the year range if the file description includes one.
Slice the model with your chosen filament settings and print. After printing, inspect the flat sealing surface for rough spots, layer lines, or warping. Light sanding with 220–400 grit sandpaper smooths the surface and improves the seal against the airbox.
Removing the airbox and installing the block off plate
Installation requires removing the airbox from the engine bay. Start with the engine cold and disconnect the negative battery terminal to avoid accidental sensor triggers. Locate the airbox under the hood on the driver's side (or passenger's side on some model years).
Unclip the intake hose from the throttle body and the mass air flow (MAF) sensor connector. Remove the bolts holding the airbox to the engine bay brackets—typically three to four 10 mm bolts. Lift the airbox out carefully; it may be tight against surrounding components.
Once the airbox is on a workbench, locate the secondary air port on the side or rear of the box. It is a circular or oval opening, usually 50–80 mm across. Clean the rim of the port with a dry cloth to remove dust and debris. Position your 3D-printed plate over the port opening and press it firmly into place. Most designs rely on a friction fit or a snap-fit lip that grips the inside edge of the port.
If your design includes bolt holes, use small stainless steel bolts (M4 or M5) and washers to find the plate. Tighten gently—over-tightening can crack the plastic. Reinstall the airbox in reverse order, reconnect the MAF sensor and intake hose, and reconnect the battery. Start the engine and listen for any unusual sounds or air leaks around the airbox seams.
Checking for fit issues and air leaks
After installation, run the engine at idle for 2–3 minutes and listen for a hissing or whistling sound that would indicate an air leak around the block off plate. A small amount of air bypass at the seal is normal, but a loud leak suggests the plate is not seated properly.
If you hear a leak, remove the airbox again and inspect the plate surface. Look for warping, gaps between the plate edge and the airbox rim, or debris preventing a tight fit. Sand the sealing surface smoother if needed, or explore a thin bead of high-temperature silicone sealant around the plate edge before reinstalling. Do not use regular silicone caulk—use a product rated for engine bay temperatures (typically labeled "high-temp" or "RTV").
Check the engine bay for any interference between the plate and surrounding components. The block off plate should sit flush inside the airbox port without touching hoses, wires, or brackets. If interference exists, you may need to trim the plate slightly or reposition it. Mark any contact points with a marker before removal so you know exactly where to sand.
After 500–1000 miles of driving, remove the airbox again and visually inspect the plate for cracks, heat damage, or deformation. PETG should show no visible wear if printed and installed correctly. If the plate has warped or cracked, the filament choice or print settings need adjustment for the next attempt.
Tuning considerations for modified and stock GT86s
On a completely stock GT86 with no other modifications, the block off plate should not trigger a check engine light. The MAF sensor and oxygen sensors continue to function normally; you are only changing the path air takes through the airbox, not the amount of air the engine receives.
If your GT86 has a custom tune, an ECU flash, or other intake modifications (cold air intake, different airbox), inform your tuner about the block off plate before or after installation. Some tuners adjust fuel and ignition maps based on intake characteristics, and a blocked secondary port may require a small tune adjustment to maintain optimal air-fuel ratio. This is usually a minor update, not a full retune.
If you are running a piggyback tuner or standalone ECU, check the tuner's documentation for airbox modifications. Most modern tuning systems account for intake path changes automatically, but it is worth confirming. If you notice rough idle, hesitation, or a check engine light after installation, the tune may need review.
Frequently Asked Questions
Will a 3D-printed block off plate damage my engine or void my warranty?
No. The plate is a passive insert with no moving parts and does not alter engine operation. It does not trigger emissions systems or affect fuel injection. Toyota and Subaru warranties do not cover modifications, but a block off plate is easily reversible—you can remove it and reinstall the stock airbox in minutes if needed.
What is the difference between a block off plate and a cold air intake?
A block off plate seals an existing port; a cold air intake replaces the entire airbox with a different design that draws air from outside the engine bay. A cold air intake changes the volume and temperature of intake air. A block off plate only changes the path within the existing airbox. They are separate modifications and can be combined.
Can I use regular PLA filament if I print the plate thicker?
No. Thickness does not change PLA's glass transition temperature. A thicker PLA plate will still warp or soften in engine bay heat. Use PETG or ABS instead.
How do I know if my 3D printer can handle PETG?
Most modern FDM printers (Prusa, Creality, Anycubic, Bambu Lab) print PETG without modification. Check your printer's manual or the manufacturer's website for PETG compatibility. If your printer has a heated bed and can reach 240°C nozzle temperature, it can print PETG. Older or budget printers may struggle with bed adhesion; a textured print bed or adhesive like glue stick helps.
Do I need to seal the block off plate with silicone or epoxy?
Not unless you have an air leak. A well-fitted plate with a smooth sealing surface creates a tight friction fit on its own. Silicone is optional and useful only if the seal is imperfect. Avoid epoxy or permanent adhesives because you may want to remove the plate later.