The 5.7L Hemi firing order is 1-8-4-3-6-5-7-2

The firing order is the sequence in which the spark plugs ignite the fuel in each cylinder. For the 5.7L Hemi engine, that sequence is 1-8-4-3-6-5-7-2. This order is fixed by the engine's design — the crankshaft, camshaft, and distributor (or coil pack arrangement) are all built to deliver spark in this exact pattern. If you're replacing spark plug wires, installing a new distributor cap, or troubleshooting a misfire, knowing this order keeps you from swapping connections and creating a no-start or rough-running engine.

The 5.7L Hemi has been used in Dodge, Jeep, and Chrysler vehicles since 2003, with slight variations in ignition systems across model years. Older models used a traditional distributor and plug wires; newer ones use coil-on-plug systems. Regardless of the ignition type, the firing order remains the same.

Key Takeaways

  • The firing order for all 5.7L Hemi engines is 1-8-4-3-6-5-7-2, and this never changes across model years or applications.
  • Cylinder numbering on the Hemi runs 1-4 on the driver's side front-to-back and 5-8 on the passenger's side front-to-back.
  • Swapping spark plug wires or coil packs in the wrong order will cause misfires, rough idle, and poor fuel economy.
  • When replacing ignition components, always double-check your work against the firing order before starting the engine.

Cylinder numbering on the 5.7L Hemi

Before you can use the firing order, you need to know which cylinder is which. On the 5.7L Hemi, cylinders are numbered 1 through 8, and the numbering follows a specific pattern. Cylinders 1, 2, 3, and 4 are on the driver's side of the engine, running from front to back. Cylinders 5, 6, 7, and 8 are on the passenger's side, also running from front to back.

Cylinder 1 is always at the front of the engine on the driver's side. This is your reference point. Once you identify cylinder 1, the rest fall into place: 2, 3, 4 going backward on that side, and 5, 6, 7, 8 on the opposite side in the same front-to-back arrangement. Your engine's service manual or a shop manual will have a diagram showing this layout if you need a visual.

Spark plug wire routing on older Hemi models

If you own a 2003–2008 5.7L Hemi with a traditional distributor cap and plug wires, the firing order tells you exactly where each wire connects. The distributor cap has eight terminals arranged in a circle, and each terminal connects to one cylinder's spark plug wire. The rotor inside the distributor spins and delivers spark to each terminal in firing order sequence.

When you remove the old wires, mark them before disconnecting them — use tape and a marker to label each wire with its cylinder number. Then, using the firing order 1-8-4-3-6-5-7-2, install the new wires one at a time. Start with cylinder 1's wire and work through the sequence. This prevents confusion and ensures you don't cross wires, which would cause the engine to run backwards or not run at all.

The distributor itself is timed so that the rotor points to cylinder 1's terminal when the piston in cylinder 1 is at top dead center on the compression stroke. If you've removed the distributor or if it has slipped on its shaft, you'll need to retime it using the firing order as your guide.

Coil-on-plug systems on newer Hemi engines

Starting around 2009, Dodge and Jeep moved away from distributor caps and plug wires toward coil-on-plug ignition systems. Each spark plug has its own coil pack mounted directly on top of it. There are no wires to route, but the firing order still controls which coil fires when.

The engine computer (PCM) controls the coil packs and fires them in the correct sequence based on crankshaft position sensor input. If you're replacing a coil pack, you straightforward unplug the old one and plug in the new one — no rewiring needed. However, if you're troubleshooting a misfire and suspect a coil pack, knowing the firing order helps you understand which cylinder is misfiring and which coil to test or replace.

What happens when the firing order is wrong

Mixing up the firing order creates when ready, obvious problems. The engine will either not start at all or will run very roughly with severe misfires. You'll hear popping and backfiring, feel heavy vibration, and see the check engine light come on. Fuel economy will drop sharply, and the engine may overheat because combustion isn't happening correctly.

If you've just replaced spark plug wires or a distributor and the engine won't start or runs badly, the first thing to check is whether the wires are in the correct firing order. Recheck each connection against the sequence 1-8-4-3-6-5-7-2. A single wire in the wrong spot will prevent the engine from running properly. On coil-on-plug systems, a misfire usually points to a bad coil pack rather than installation error, since there's no way to install a coil pack incorrectly.

Timing marks and top dead center

The firing order works in concert with engine timing. The crankshaft has a timing mark, and the timing cover has a pointer. When cylinder 1 is at top dead center (TDC) on the compression stroke, the timing mark aligns with the pointer. At this moment, the distributor rotor (on older models) should point to cylinder 1's terminal, and the spark plug in cylinder 1 should fire.

If you've removed and reinstalled a distributor, you must retime it so the rotor points to cylinder 1 when the crankshaft timing mark is at TDC. Failure to do this will throw off the entire firing order sequence, even if the wires are connected in the right numerical order. Your service manual will walk you through the retiming procedure step by step.

Checking your work before starting the engine

After replacing spark plug wires, a distributor cap, or any ignition component, take five minutes to verify the firing order before you turn the key. Start at cylinder 1 and trace each wire or coil pack through the sequence 1-8-4-3-6-5-7-2. Write down what you see and compare it to the sequence. If all eight connections match the firing order, you're ready to start.

If you find a mistake, fix it before starting. Trying to start an engine with the wrong firing order can damage the ignition system and waste time troubleshooting. A quick visual check takes less than a minute and saves you from a no-start condition or a rough-running engine that requires more diagnosis later.

Frequently Asked Questions

Can I change the firing order to improve performance?

No. The firing order is determined by the engine's mechanical design — the crankshaft, camshaft, and cylinder arrangement. You cannot change it without completely redesigning the engine. Any modification that alters the firing order would break the engine.

Does the firing order differ between 2003 and 2023 Hemi engines?

The firing order 1-8-4-3-6-5-7-2 is the same across all 5.7L Hemi engines regardless of model year. The ignition system changed from distributor-based to coil-on-plug, but the firing sequence itself never changed.

What if I only need to replace one spark plug wire?

Identify which cylinder that wire serves using the firing order and cylinder numbering, then replace only that wire. You don't need to touch the others. Mark the old wire with its cylinder number before removing it so you know exactly where the new one goes.

How do I know which cylinder is misfiring?

A diagnostic scanner will read the misfire code and tell you the cylinder number. Once you know the cylinder, use the firing order to understand the sequence and check that cylinder's ignition component — the spark plug wire, coil pack, or spark plug itself.