The Chevy 350 fires cylinders in this sequence: 1-8-4-3-6-5-7-2
The firing order is the sequence in which spark plugs ignite the fuel mixture in each cylinder. For a Chevy 350 small-block engine, that sequence is always 1-8-4-3-6-5-7-2, whether you're working on a 1967 model or a 1990s version. This order matters because it affects how you route spark plug wires, where you position the distributor rotor, and how the engine runs. Get it wrong and your engine will misfire, run rough, or not start at all.
The firing order is determined by the engine's crankshaft and camshaft design — you cannot change it. It is fixed the moment the engine block is cast. What you can control is making sure your spark plug wires follow that order correctly when you install or replace them.
Key Takeaways
- Chevy 350 firing order is 1-8-4-3-6-5-7-2, and this sequence never changes across different model years or applications.
- Cylinder numbering on a Chevy 350 runs 1-2-3-4 on the driver's side (front to back) and 5-6-7-8 on the passenger side (front to back).
- The distributor cap has a marked position for cylinder 1, and spark plug wires must follow the firing order around the cap in the correct direction of rotor rotation.
- Mixing up spark plug wires is the most common cause of firing order problems, and swapping even two wires will cause the engine to run poorly or not run at all.
How cylinder numbering works on a Chevy 350
On a Chevy 350, cylinders are numbered from front to back on each side of the engine. Cylinders 1, 2, 3, and 4 are on the driver's side. Cylinders 5, 6, 7, and 8 are on the passenger side. The front of the engine is where the crankshaft pulley and timing cover sit; the back is where the transmission bolts on.
This layout matters because when you look at a distributor cap from above, you will see eight terminals arranged in a circle. One terminal is marked for cylinder 1 — usually with a notch, a number, or a raised bump on the cap. The remaining terminals follow the firing order around the cap. If you do not know which terminal is number 1, check the cap itself or your engine manual before you touch a single wire.
Routing spark plug wires correctly
Start by locating the number 1 terminal on your distributor cap. This terminal connects to the spark plug in cylinder 1 (driver's side, front). From there, follow the firing order 1-8-4-3-6-5-7-2 around the cap. Each wire goes to the next terminal in sequence as you move around the cap in the direction the rotor spins.
On most Chevy 350 engines with a traditional points or electronic distributor, the rotor spins clockwise. That means if cylinder 1 is at the top of the cap, cylinder 8 is the next terminal clockwise, then cylinder 4, and so on. If your distributor spins counterclockwise (rare but possible in some applications), the order reverses around the cap, but the firing sequence itself stays the same.
Write down the firing order before you remove old wires. Take a photo of the cap with the wires attached, or label each wire with tape and a marker. This step takes two minutes and prevents hours of troubleshooting later.
What happens when firing order is wrong
An incorrect firing order causes the engine to misfire because spark plugs ignite cylinders out of sequence. The engine may start briefly, then stall. It may run but shake violently, backfire through the carburetor or intake, or produce black smoke from the exhaust. Power output drops sharply, and fuel consumption rises.
The most common mistake is swapping two adjacent wires. Even a single wire in the wrong position breaks the sequence and causes noticeable problems. A completely reversed firing order (running 2-7-5-6-3-4-8-1 instead of 1-8-4-3-6-5-7-2) will prevent the engine from running at all.
Distributor position and rotor alignment
The distributor itself must be installed so the rotor points to the number 1 terminal when cylinder 1 is at top dead center on the compression stroke. If the distributor is installed 180 degrees out, the rotor will point to the wrong terminal and the firing order will be reversed. If it is off by one tooth on the timing chain, the entire sequence shifts and the engine will not run correctly.
When you remove a distributor, mark the rotor position on the engine block or housing before you pull it out. When you reinstall it, align the rotor back to that mark. If you do not know the original position, you can find it by turning the engine to top dead center on cylinder 1 (using the timing marks on the crankshaft pulley) and then rotating the distributor until the rotor points at the number 1 terminal on the cap.
Checking your work after installation
After you route all spark plug wires, double-check each one against the firing order before you start the engine. Trace each wire from the cap terminal to the spark plug it connects to, and verify that terminal matches the firing order sequence. A second set of eyes helps catch mistakes.
Start the engine and listen for rough running, backfiring, or stalling. If the engine runs but sounds wrong, turn it off when ready and recheck the wire routing. Do not drive the vehicle until the firing order is confirmed correct — running on the wrong sequence can damage the catalytic converter and waste fuel.
Frequently Asked Questions
Can I run a Chevy 350 with the firing order reversed?
No. A reversed firing order will prevent the engine from running at all or cause it to run so poorly that it stalls when ready. The engine is designed to fire in one specific sequence, and reversing it breaks the combustion cycle.
Does firing order change if I swap to a different distributor?
The firing order itself never changes — it is built into the engine design. However, different distributors may have different rotor rotation directions or terminal layouts. Always check the new distributor's documentation to confirm how its terminals align with the 1-8-4-3-6-5-7-2 sequence.
What if I cannot find the number 1 terminal on my distributor cap?
Look for a notch, raised bump, or printed number on the cap itself. If the cap is unmarked, consult your engine manual or the distributor manufacturer's documentation. You can also contact a Chevy 350 specialist or check online forums specific to your engine year and process.
Will a wrong firing order throw a check engine light?
On older carbureted Chevy 350 engines without computer controls, no. On fuel-injected models with an engine control computer, yes — the computer will detect misfires and illuminate the check engine light. The misfire code will help you identify which cylinder is firing at the wrong time.
How do I know which direction the rotor spins on my distributor?
Most Chevy 350 distributors spin clockwise, but the only way to be certain is to remove the cap and turn the engine over by hand (using a wrench on the crankshaft pulley) while watching the rotor. It will rotate in the direction the engine turns the distributor shaft. Mark this direction before you install spark plug wires.