Engine coil replacement typically costs between $150 and $400 per coil, plus labour that runs $100 to $300 depending on how many coils your engine has and how accessible they are.

The total bill depends on three things: how many coils have failed, what your vehicle costs to work on, and whether you replace one at a time or all of them together. A four-cylinder engine has four coils; a six-cylinder has six. Some sit on top of the spark plugs where a technician can reach them in minutes. Others live deep in the engine bay where removing other parts becomes necessary.

Most people discover a coil problem when their engine misfires—the car shakes at a stoplight, the check engine light comes on, or it struggles to start. A scan tool reads the fault code and tells you which cylinder is misfiring. That tells you which coil has likely failed. You then decide whether to replace just that one or all of them at once, a choice that affects both when ready cost and future reliability.

Key Takeaways

  • A single coil costs $150 to $400 in parts; labour adds $100 to $300 depending on engine design and how many coils need removal to reach the bad one.
  • Replacing all coils at once costs more upfront but prevents repeat visits if other coils are aging, and some technicians offer a small discount for the full set.
  • A misfire code points to a specific cylinder, but that does not always mean the coil itself has failed—a fouled spark plug, bad fuel injector, or compression loss can cause the same symptom.
  • Ignoring a misfire damages the catalytic converter over time, which costs $800 to $2,000 to replace and is far more expensive than addressing the coil now.

What a coil pack actually does and why it fails

An ignition coil takes 12 volts from your battery and steps it up to 20,000 to 40,000 volts in a fraction of a second, then sends that spike to a spark plug to ignite the fuel-air mixture. It does this thousands of times per minute while sitting in an engine bay where temperatures swing between freezing and 200 degrees Fahrenheit. The coil is a tightly wound transformer wrapped in resin to insulate it. Over time, heat cycles crack that resin, moisture seeps in, and the coil shorts internally or loses its ability to generate the voltage needed.

Most coils last 80,000 to 150,000 miles, though some fail much earlier if the spark plug is bad (a fouled plug forces the coil to work harder), the fuel is contaminated, or the engine runs too hot. A coil that is beginning to fail often produces an intermittent misfire—the car runs fine for a week, then shakes for a day, then runs fine again. This pattern is the coil's insulation breaking down gradually.

Single coil versus replacing the whole set

When a scan tool shows a misfire on cylinder three, the obvious choice is to replace the coil on cylinder three and stop. This costs the least money right now. However, if your car has 120,000 miles and the coils are original, the other coils are aging too. They may fail within weeks or months. You then pay labour a second time to remove the engine cover or other components again.

Replacing all coils at once costs more upfront—perhaps $600 to $1,200 in parts for a six-cylinder engine—but eliminates the risk of a second failure soon after. Many independent shops offer a 10 to 20 percent discount when you replace the full set, which reduces the total labour cost. If your vehicle has high mileage and the coils are original, replacing all of them is often the smarter financial move because you avoid a second service call.

The middle ground is to replace the failed coil now and the rest during your next scheduled service, spreading the cost across two visits. This works if you can tolerate the risk of another misfire in the meantime.

Labour costs depend on engine design

A four-cylinder engine with coils mounted directly on top of the spark plugs takes 30 to 60 minutes to service—one coil at a time, unplug, unbolt, replace, done. Labour on that job runs $100 to $150. A six-cylinder engine with the same design takes 60 to 90 minutes and costs $150 to $225 in labour.

Some engines hide the coils under intake manifolds, valve covers, or other components that must come off first. Removing a valve cover takes an extra 30 to 60 minutes. Removing an intake manifold can add two hours. On those vehicles, labour to replace a single coil can reach $300 to $400, and replacing all six coils might take four to six hours of labour—$400 to $600 in labour alone. Always ask your technician whether the coils are accessible or whether other parts must come off first.

Misfire codes do not always mean a bad coil

A fault code P0300 (random misfire) or P0301 (misfire on cylinder one) tells you the engine is not firing consistently on that cylinder. The coil is the most common cause, but not the only one. A fouled spark plug, a leaking fuel injector, low fuel pressure, a vacuum leak, or low compression in that cylinder all produce the same code.

A good technician will check the spark plug first—it costs nothing and takes two minutes. If the plug is black and wet with fuel, the injector is leaking, not the coil. If the plug is white and burned, the engine is running too hot or the fuel is too lean. If the plug looks normal but the coil voltage is low when tested, the coil is the problem. Skipping these checks and replacing the coil without diagnosis wastes money if the real problem is elsewhere.

Why a misfire becomes expensive if you ignore it

A misfiring cylinder sends unburned fuel into the exhaust system. The catalytic converter is designed to burn that fuel, but continuous misfires overheat the converter and damage its internal honeycomb structure. Once that happens, the converter cannot be repaired—it must be replaced. A catalytic converter costs $800 to $2,000 in parts and labour, depending on the vehicle.

A misfire also increases emissions and fails a smog test in states that require one. Some states will not renew your registration until the vehicle passes. The longer you drive on a bad coil, the higher the risk of converter damage and the more fuel you waste. Replacing a coil within a week or two of the first misfire prevents this cascade of problems.

What to expect during the repair

Your technician will connect a scan tool to read the fault code and identify which cylinder is misfiring. They will then remove the coil (or coils) and inspect the spark plug. If the plug is fouled, they will clean or replace it. If the plug is normal, they will test the old coil's output with a multimeter or coil tester. If the output is low, the coil is bad and will be replaced. If the output is normal, the problem lies elsewhere—fuel pressure, compression, or injector function—and further diagnosis is needed.

Once the new coil is installed, the technician will clear the fault code and test-drive the vehicle to confirm the misfire is gone. Some shops will retest after 50 miles to make sure the code does not return. If you chose to replace only one coil and another fails within a few weeks, most shops will honour a warranty on the first coil and replace the second one at a reduced labour rate since they are already in the engine bay.

Frequently Asked Questions

Can I replace a coil myself if I have basic tools?

If your coils sit on top of the spark plugs with no other components blocking them, yes—it is one bolt and one electrical connector per coil. If your coils are buried under a valve cover or intake manifold, the job requires removing those parts, which demands more experience and special tools. Check your repair manual or ask your technician whether the job is accessible before you attempt it.

Will replacing the coil fix the check engine light?

Yes, once the new coil is installed and the engine runs without misfiring for a few minutes, the light will go out on its own or can be cleared with a scan tool. If the light returns after a few days, the original problem was not the coil, and further diagnosis is needed.

Should I replace the spark plugs at the same time as the coils?

If your spark plugs are due for replacement based on your maintenance schedule, yes—you are already paying labour to access the engine. If the plugs are relatively new and look normal, you can skip them. A fouled or worn plug can cause a coil to fail prematurely, so replacing both eliminates that risk.

What is the difference between a coil pack and a coil-on-plug design?

A coil pack is a single unit with multiple coils inside, mounted away from the engine and connected to spark plugs by wires. Coil-on-plug means each coil sits directly on its spark plug. Coil-on-plug is more common on newer vehicles and is easier to service because you do not need to replace wires. Both designs fail the same way and cost roughly the same to replace.

Is it normal for coils to fail at a certain mileage?

Coils typically last 80,000 to 150,000 miles, but this varies widely. Extreme heat, poor fuel quality, a bad spark plug, or a malfunctioning cooling system can shorten coil life. Some vehicles see original coils at 200,000 miles; others fail at 60,000. If one coil fails early, the others are likely aging too.