What electric start does and why you might want it on a Predator 212
The Predator 212 is a small single-cylinder engine that comes from the factory with pull-cord starting only. Electric start means replacing that pull cord with a battery-powered starter motor that turns the engine over when you press a button. On a Predator 212, this is a retrofit — you buy the parts separately and install them yourself or have a mechanic do it.
The practical reason to add electric start is convenience and reliability. A pull cord works, but it requires physical effort, and on cold mornings or after the engine has sat for weeks, you may need to pull it many times before it catches. A starter motor does the same job with one button press, every time, regardless of temperature or how long the engine has been idle. For equipment that runs regularly — a generator, a go-kart, a pressure washer — this matters.
The trade-off is cost and added weight. A complete electric-start kit for a Predator 212 runs between $150 and $300 depending on the supplier and whether you need a new flywheel. You also add a battery, wiring, and a charging system, which increases the total engine weight by several pounds. For stationary equipment like a generator, that weight is irrelevant. For a go-kart or other vehicle, it may not be.
Key Takeaways
- Electric start requires a new flywheel with a ring gear, a starter motor, a battery, and a charging coil — these are sold as kits or individually.
- The flywheel swap is the most involved part of the job and requires removing the engine's clutch and crankshaft hardware.
- You need a battery (usually 12V) and a way to keep it charged; some kits include a charging coil, others require an external charger.
- Total cost ranges from $150 to $300 for parts, plus labor if you do not install it yourself.
- Once installed, electric start is more reliable than pull-cord starting in cold weather and after long idle periods.
The parts you need for a Predator 212 electric-start conversion
A complete conversion requires four main components. The flywheel with ring gear replaces the original flywheel; the ring gear is a toothed ring that the starter motor engages. The starter motor is a small electric motor bolted to the engine block that spins the ring gear. The battery supplies power to the starter; most Predator 212 conversions use a 12-volt battery, either a small sealed lead-acid unit or a lithium-ion pack. The charging coil (or stator) generates electricity to recharge the battery while the engine runs.
Many suppliers sell these as kits that include the flywheel, starter, and wiring harness. You then buy a battery separately, or the kit may include a small battery. Check the kit description to see what is included and what you must source yourself. Some kits do not include a charging system, which means you will need to charge the battery with an external charger between uses — acceptable for occasional use, inconvenient for daily operation.
The original Predator 212 flywheel is not compatible with a starter motor. You cannot straightforward bolt a starter to the engine and expect it to work; the new flywheel must be the correct size and tooth count for the starter motor you are using. Most kits are designed to work together, so buy them from the same supplier to avoid mismatch.
How to remove the old flywheel and install the new one
Removing the flywheel is the most time-consuming part of the conversion. First, drain the oil and remove the engine from whatever equipment it powers. You will need to access the crankshaft, which means removing the clutch (if present), the fan shroud, and the engine cover. On a Predator 212, these bolt on and come off in sequence.
Once the crankshaft is exposed, you will see the flywheel bolted to the crankshaft with a key — a small metal pin that prevents the flywheel from spinning independently. Remove the bolts holding the flywheel, then carefully pull the flywheel straight off the crankshaft. The key will come out with it or stay in the crankshaft; either way, keep it safe because you will reuse it with the new flywheel.
Slide the new flywheel onto the crankshaft, align the keyway (the slot where the key sits), insert the key, and bolt the flywheel back down. Torque the bolts to the specification in your engine manual — usually around 25 to 35 foot-pounds for a Predator 212. Do not guess at this; under-torqued bolts can loosen and cause the flywheel to slip, and over-torqued bolts can strip the threads or crack the flywheel.
Installing the starter motor and wiring it to the battery
The starter motor bolts to the engine block, usually to a mounting boss on the side near the crankshaft. The exact location depends on your kit, so follow the instructions that come with it. The starter has two electrical connections: a heavy cable that carries power from the battery, and a thin wire that carries the signal from the ignition switch or push button.
Run the heavy cable from the positive terminal of the battery to the starter motor's main terminal. This cable should be as short as practical and should have an inline fuse rated for the starter current — typically 30 to 50 amps. The fuse protects the wiring in case of a short circuit. Run the signal wire from your ignition switch or push button to the starter's solenoid terminal; this wire can be thinner because it carries very little current.
Mount the battery securely to the equipment frame or engine block using a battery box or strap. A loose battery can shift during operation and break the cable connections. If your kit includes a charging coil, it will have two or three wires that connect to a small regulator/rectifier unit, which then connects to the battery. Follow the wiring diagram in your kit instructions exactly; incorrect wiring can damage the charging system or the battery.
Charging systems: built-in versus external
Some electric-start kits include a charging coil that generates electricity while the engine runs, keeping the battery topped up. This is the most convenient option because you never have to think about the battery — it charges itself during normal operation. The charging coil is a set of windings on the stator (the stationary part of the magneto) that produces AC current, which a regulator/rectifier converts to DC current suitable for charging the battery.
Other kits do not include a charging system, which means the battery will slowly discharge every time you start the engine. For equipment that runs frequently — a generator running several hours a week — this is usually not a problem because the battery gets used and recharged often. For equipment that sits idle for weeks, you will need to charge the battery with an external charger before use, or the starter will not have enough power to turn the engine over.
If your kit does not include charging, you have two options: buy a separate charging coil and regulator/rectifier from the same supplier (if available), or plan to charge the battery manually using a small 12-volt charger. A manual charger costs $20 to $50 and takes a few hours to fully charge a small battery, so this is practical only if you use the equipment regularly enough that the battery does not fully discharge between uses.
Common problems and how to avoid them
The most frequent issue is a starter that does not engage or engages weakly. This usually means the battery voltage is too low — either the battery is discharged, the connections are corroded, or the charging system is not working. Check the battery voltage with a multimeter; it should read at least 11 volts at rest and 12.5 to 13.5 volts while the engine is running (if you have a charging system). Clean any corrosion off the battery terminals with a wire brush and reconnect them firmly.
Another common problem is the starter motor spinning but the engine not turning over. This means the ring gear on the flywheel is not meshing with the starter pinion (the small gear on the starter). This can happen if the flywheel was installed slightly off-center or if the starter mounting bolts are loose. Remove the starter, check that the flywheel is seated fully on the crankshaft, and reinstall the starter, making sure it is bolted down tight.
If the engine starts but the battery drains quickly, your charging system is not working. Check the regulator/rectifier connections and the charging coil wires for loose or corroded connections. If the connections are good, the charging coil or regulator may be faulty and will need to be replaced. If you do not have a charging system, this is normal — the battery will discharge over time, and you will need to recharge it periodically.
When to have a mechanic do the work instead
If you are comfortable removing engine covers and working with basic hand tools, you can do this conversion yourself. The flywheel removal and installation is straightforward, and the wiring is straightforward — just heavy cable and a signal wire. However, if you have never worked on small engines or are unsure about torque specifications, having a mechanic handle the flywheel swap is worth the cost. A mistake here — a loose flywheel or incorrect torque — can cause serious damage.
The wiring is easier to do yourself because mistakes are less likely to damage the engine. If you reverse the battery polarity, the worst that happens is the starter does not work; you straightforward reverse the cables and try again. If you do not feel confident with the wiring, a mechanic can do it in an hour or two, which is usually less than the cost of the parts themselves.
Frequently Asked Questions
Can I use a 6-volt battery instead of 12-volt?
No. A 6-volt starter motor will not fit a Predator 212, and a 12-volt starter will not work on a 6-volt battery — it will turn too slowly to crank the engine. All modern electric-start kits for the Predator 212 are 12-volt. If you have an older kit, check the documentation to confirm the voltage before you buy a battery.
Do I need to remove the engine from the equipment to change the flywheel?
Usually yes. You need access to the crankshaft, which means removing the clutch, fan shroud, and engine cover. On most equipment, this is easier if you remove the engine entirely, but some designs allow you to do it in place. Check your equipment manual or ask the supplier whether the conversion can be done without removal.
Will electric start make my engine heavier or slower?
Yes, slightly. The starter motor, battery, and wiring add 5 to 10 pounds depending on the battery type. For a stationary generator, this is irrelevant. For a go-kart or other vehicle, it may reduce acceleration slightly, but most users do not notice the difference. The convenience of electric start usually outweighs the small weight penalty.
What happens if the battery dies while I am using the equipment?
The equipment will not start again until the battery is recharged. If you have a charging system, the battery should not die during normal use because it recharges while the engine runs. If you do not have a charging system and the battery is low, you can still pull-start the engine manually — the pull cord is still there, just not used. This is a good reason to keep the pull cord intact even after adding electric start.
Can I add electric start to a Predator 212 that already has a clutch?
Yes. The clutch bolts to the flywheel, so you remove the clutch, swap the flywheel, and reinstall the clutch on the new flywheel. The process is the same, just with an extra step. Make sure the new flywheel has the same bolt pattern as the old one, or the clutch will not fit.