An electric jack lifts your RV by running a motor that extends a hydraulic or mechanical arm, letting you raise the vehicle without hand-cranking or relying on your vehicle's factory jack
An electric jack is a powered lifting tool designed for RVs and trailers. Unlike a manual scissor jack or bottle jack that you operate by hand, an electric jack uses a 12-volt or 110-volt motor to do the work. You press a button or flip a switch, and the motor extends the lifting mechanism until your RV reaches the height you need. Most electric jacks for RVs mount permanently to the frame and can lift one corner or the entire front or rear axle, depending on the model.
The real advantage is speed and physical effort. Raising an RV by hand takes time and strength, especially if you're doing it alone or if the ground is soft. An electric jack does the same job in seconds. For people with mobility issues, older owners, or anyone who changes their own tires or does roadside repairs, an electric jack removes a significant barrier to self-sufficiency.
Key Takeaways
- Electric jacks mount to your RV frame and use a motor to lift the vehicle, eliminating hand-cranking and reducing physical strain.
- Most RV electric jacks run on 12-volt power from your coach battery or a portable power source, though some models require 110-volt shore power.
- A single electric jack typically lifts one corner of the RV; multiple jacks can be wired together to raise the front or rear axle at once.
- Electric jacks cost between $300 and $1,200 per unit depending on lifting capacity and whether they include wireless controls or integrated safety features.
- Proper installation requires mounting to the frame (not the body), securing electrical connections, and testing the lift before relying on it for maintenance work.
How the motor and lifting mechanism work together
Inside an electric jack, a 12-volt or 110-volt motor drives a gear system or hydraulic pump. That pump pressurizes fluid or turns a screw mechanism, which extends the lifting arm or column. When you release the button, the motor stops and the arm stays extended, holding the RV at that height. To lower the vehicle, you press the down button, which reverses the motor and retracts the arm.
The lifting arm itself is usually made of steel and rated for a specific weight capacity—typically 5,000 to 15,000 pounds per jack, depending on the model. The arm extends from a base that bolts to your RV frame. Because the motor does the work, you don't need to be strong or coordinated to operate it. A child or someone with limited mobility can raise or lower the RV safely, as long as the jack is properly installed and maintained.
Safety is built into the design. Most electric jacks have a pressure relief valve that prevents over-extension, and many include a manual override so you can lower the RV if the power fails. Some newer models have wireless remote controls, so you can operate the jack from outside the RV and watch the lift happen in real time.
Power requirements and electrical setup
Most RV electric jacks draw power from your coach battery—the 12-volt system that runs your lights, water pump, and other onboard systems. A single jack typically draws 50 to 100 amps during operation, which is why you need a battery in good condition and often a heavy-gauge wire run directly from the battery to the jack. If your battery is weak or your wiring is undersized, the jack will lift slowly or not at all.
If you're installing multiple jacks (one at each corner, for example), the total power draw can exceed what a single battery can supply. Many RV owners add a second auxiliary battery or upgrade to a lithium battery system to handle the load. Some jacks can be wired in parallel so they lift together, which distributes the power draw and speeds up the process.
Shore power (110-volt) electric jacks exist but are less common for RVs because they require you to be plugged in at a campground or have a generator running. Most owners prefer 12-volt jacks for the flexibility of lifting anywhere, anytime, as long as the battery has charge.
Single jacks versus multiple-jack systems
A single electric jack lifts one corner of your RV. This is useful for changing a tire, accessing the undercarriage, or leveling one side. However, if you want to lift the entire front or rear axle evenly, you need at least two jacks working together—one on each side of the axle.
Multiple jacks can be wired to operate simultaneously with a single switch, so both sides lift at the same rate and height. This prevents the RV from tilting and reduces stress on the frame. Some systems include a control box that monitors each jack's position and stops them if one gets ahead of the other, adding an extra layer of safety.
The cost difference is significant. A single jack runs $300 to $600; a four-corner system (one at each wheel) can cost $1,200 to $2,000 or more. Most RV owners start with two jacks for the front or rear axle and add more later if needed.
Installation and frame mounting
Electric jacks must bolt to the RV frame, not the body. The frame is the steel structure that carries the weight; the body is the fiberglass or aluminum shell. Mounting to the body will tear through the material under load and could cause the RV to collapse during a lift. A may have access to technician will locate a solid frame member, drill holes, and bolt the jack base securely using grade-8 bolts and lock washers.
The electrical work is equally important. The power wire from the battery to the jack must be heavy gauge (typically 2 or 4 AWG) to handle the current without overheating. The wire runs through a fused disconnect switch mounted near the battery, so you can cut power in an emergency. The control switch or remote receiver mounts inside the RV where you can reach it easily.
After installation, the jack should be tested under no load first—just raise and lower it a few times to confirm smooth operation. Then test it with the RV parked on level ground, raising one corner a few inches and holding it for several minutes to check for drift or leaks. Only after passing these tests should you rely on the jack for maintenance work.
Safety considerations and common mistakes
The biggest mistake is using an electric jack as a leveling system for parking. Jacks are designed for temporary lifts during maintenance, not for holding an RV level for days or weeks. Hydraulic pressure can drift, seals can fail, and a slow leak can lower the RV without warning. Always use your RV's built-in leveling jacks or stabilizer jacks for parking, and use electric jacks only for tire changes, repairs, and brief inspections.
Never work under an RV supported only by a jack. Always place jack stands rated for at least the weight of the RV section you're lifting. A jack can fail—a seal can rupture, a wire can corrode, a motor can burn out. Jack stands are your backup. If the jack fails, the stands catch the RV and prevent it from crushing you or damaging the vehicle.
Keep the jack clean and dry. Mud, salt, and water corrode the electrical connections and hydraulic seals. After using the jack, wipe it down and check the connections for corrosion. If you store the RV for the winter, lower the jacks fully so the seals aren't under constant pressure, and disconnect the battery to prevent slow drain.
Maintenance and troubleshooting
Electric jacks are straightforward machines with few moving parts, so maintenance is straightforward. Check the battery voltage before each use—if it's below 12 volts, charge it fully before lifting. Listen for unusual sounds during operation: grinding or squealing usually means the motor is struggling, often because the battery is weak or the wiring is corroded.
If a jack lifts slowly on one side but normally on the other, the slower jack may have a weak motor or a partial hydraulic leak. If a jack won't lift at all, check the fuse first, then the battery voltage, then the wiring connections. Corrosion at the battery terminal or the jack connector is a common culprit and can usually be cleaned with a wire brush.
If a jack drifts down after you've raised it, the internal seal is leaking. This is a sign the jack needs service or replacement. Some manufacturers sell rebuild kits, but for most RV owners, replacement is simpler and more reliable. A leaking jack is a safety hazard and should not be used for anything but the lightest work.
Frequently Asked Questions
Can I use a regular automotive electric jack on my RV?
Not safely. Automotive jacks are designed for cars and light trucks, which weigh 3,000 to 5,000 pounds. An RV weighs 10,000 to 30,000 pounds or more. An undersized jack will strain the motor, overheat, and fail under load. You need a jack rated for your RV's actual weight, which is printed on the door jamb or in your owner's manual.
What happens if the battery dies while the RV is lifted?
Most electric jacks have a manual override—a hand crank or a valve you can turn to lower the RV manually. This takes time and effort, but it works. Some newer jacks include a gravity-feed system that lowers the RV slowly if power is lost. Check your jack's manual for the override procedure and practice it before you need it in an emergency.
Do I need a second battery to run electric jacks?
A single quality deep-cycle battery can run one or two jacks if it's in good condition. If you plan to use four jacks or lift frequently, a second battery or a lithium upgrade will give you more reliable power and faster lift times. Your RV's existing battery may be sized for lights and water pumps, not for the high current draw of a jack.
How much weight can an electric jack lift?
Each jack is rated for a specific capacity, usually 5,000 to 15,000 pounds. Your RV's weight is divided among all four wheels. To find the weight on one wheel, divide the total RV weight by four. A 20,000-pound RV puts about 5,000 pounds on each wheel, so a single 5,000-pound jack can lift one corner. For safety, choose a jack rated for at least 1.5 times the expected load.
Can I install an electric jack myself?
If you're comfortable with basic tools and electrical work, you can install a jack. The hardest part is finding a solid frame mounting point and drilling accurate holes. The electrical work is straightforward—run wire from the battery through a fused switch to the jack. If you're unsure about frame location or wiring, have a technician do the work. A poor installation can damage the RV or create a safety hazard.