What You Need Before You Start

An oil change in a Dodge Charger takes 30 to 45 minutes if you have the right tools and know where everything sits under the hood. You will need an oil drain pan (to catch old oil), a wrench or socket set to remove the drain plug, an oil filter wrench, fresh oil in the weight your Charger calls for, a new oil filter, and jack stands if you need clearance to slide underneath. Most Chargers sit high enough that you can work without lifting, but check your model year — some earlier generations sit lower.

The oil type and capacity depend on your engine. A V8 Charger typically holds 5 to 6 quarts and uses 5W-30 or 10W-30 synthetic or conventional oil. Your owner's manual or the inside of the driver's door jamb will show the exact specification for your year and engine. Buying the wrong weight will not damage the engine when ready, but it can affect fuel economy and cold-start performance, so match what the manual says.

You will also need a way to dispose of the old oil. Do not pour it down a drain or into the ground. Most auto parts stores take used oil for free, and many will also take the old filter. Some Dodge dealers will accept it too, though they may charge a small fee.

Key Takeaways

  • Drain the old oil while the engine is warm but not hot, then replace the drain plug and tighten it by hand plus a quarter turn with a wrench to avoid stripping the threads.
  • The oil filter on most Chargers sits on top of the engine and unscrews by hand; coat the rubber gasket on the new filter with fresh oil before installing it.
  • Fill the engine with the exact oil weight and amount listed in your owner's manual, then run the engine for 30 seconds and check the level again.
  • Reset the oil change reminder on your dashboard after you finish, or it will alert you at the next service interval even though you just changed it.

Locating the Drain Plug and Oil Filter

The drain plug sits at the lowest point of the oil pan, underneath the engine. On most Dodge Chargers, it is on the passenger side of the pan and points downward at an angle. You will see a bolt head, usually 13mm or 15mm depending on the year. Slide your drain pan underneath it before you loosen anything — old oil will flow fast and splash if you are not ready.

The oil filter location varies by engine. On V8 models, it typically sits on top of the engine toward the rear, mounted vertically. On some inline-six or turbocharged models, it may be on the side. Check your owner's manual or look at the engine bay with the hood open; the filter is a cylindrical canister about the size of a soda can, usually white or blue plastic with a rubber gasket around the base.

Draining Old Oil and Replacing the Plug

Start with the engine warm but not hot — you want the oil thin enough to flow freely, but not so hot that it burns your hands. Let the engine cool for five minutes after you turn it off. Loosen the drain plug by turning it counterclockwise with your wrench, then unscrew it by hand once it is loose enough to grip. Oil will pour out, so keep the pan directly underneath.

Let the pan sit for a few minutes so the last of the oil drains from the pan and the filter housing. While you wait, inspect the drain plug for damage. If the threads are stripped or the plug is bent, you will need to replace it — a new one costs $5 to $15 and prevents leaks. Wipe the plug clean with a rag, then screw it back in by hand until it is snug. Use your wrench to tighten it an additional quarter turn — no more. Over-tightening strips the aluminum threads in the pan and creates a leak that is expensive to fix.

Removing and Installing the Oil Filter

Position your drain pan under the filter before you touch it — there is always a little oil left inside. Grip the filter with your oil filter wrench and turn it counterclockwise. Once it is loose, unscrew it by hand and tip it so the remaining oil drains into the pan. Set the old filter aside for disposal.

Wipe the filter mounting surface on the engine with a clean rag to remove any dirt or old gasket material. Take the new filter and coat the rubber gasket (the ring around the base) lightly with fresh oil from your new bottle. This creates a seal and makes the next oil change easier. Screw the new filter on by hand until the gasket touches the mounting surface, then turn it an additional three-quarters of a turn. Do not use the wrench — hand-tight is correct, and over-tightening will damage the gasket and cause leaks.

Filling with Fresh Oil and Checking the Level

Locate the oil filler cap on top of the engine — it usually has an oil can symbol on it. Unscrew it and set it aside. Pour in the amount of oil your manual specifies, usually 5 to 6 quarts for a V8 Charger. Pour slowly and pause halfway through to let the oil settle into the pan and filter. Once you have added the full amount, replace the cap.

Start the engine and let it run for 30 seconds, then turn it off. Wait two minutes for the oil to settle back into the pan, then pull the dipstick (a long rod with markings on it, usually with a yellow or orange handle). Wipe it clean on a rag, reinsert it fully, then pull it out again to read the level. The oil should be between the minimum and maximum marks. If it is low, add a half-quart at a time and check again. If it is overfull, you will need to drain a little out through the drain plug — overfilled oil can damage the engine.

Resetting the Oil Change Reminder

Most Dodge Chargers from 2008 onward have an oil change reminder that displays on the dashboard. After you finish the oil change, you need to reset it or it will continue counting down and alert you at the next interval. The reset method depends on your model year and whether you have a traditional instrument cluster or a digital display.

For most Chargers, turn the ignition to the "On" position without starting the engine. Use the arrow buttons on the steering wheel or dashboard to navigate to the "Service" or "Maintenance" menu, then select "Oil Change Reset" or "Reset Service Interval." Confirm the reset. If your Charger has an older mechanical odometer, there may be no reminder to reset. Consult your owner's manual for your specific year if you are unsure how to access the menu.

Disposing of Old Oil and Filters

Do not throw used oil or filters in the trash or pour them down a drain. Most auto parts retailers — AutoZone, O'Reilly, NAPA, and Advance Auto Parts — accept used oil and filters for free, no purchase required. Some Dodge dealerships also accept them, though a few charge a small fee. Call ahead if you are unsure.

If you generated more than a few quarts, your city or county may have a hazardous waste collection day where you can drop off oil for free. Search "[your city] hazardous waste disposal" to find the schedule and location.

Frequently Asked Questions

How often should I change the oil in my Dodge Charger?

Most modern Chargers with synthetic oil can go 7,500 to 10,000 miles between changes. Older models or those using conventional oil typically need a change every 3,000 to 5,000 miles. Your owner's manual will specify the interval for your year and engine type. Some Chargers have an oil life monitoring system that calculates when you actually need a change based on driving habits, so follow that if your model has one.

What if I spill oil on the driveway?

Soak it up when ready with cat litter, sand, or oil absorbent material — do not let it sit. Once it is absorbed, sweep it into a bag and dispose of it as hazardous waste. For large spills, contact your local environmental agency for guidance. Oil stains that have already set can be treated with a degreaser, but prevention is easier than cleanup.

Can I change the oil without lifting the Charger?

Most Chargers sit high enough that you can access the drain plug and filter without a jack. If you are very tall or the ground is uneven, you may need to lift the front end slightly with a jack and find it with jack stands. Never work under a car supported only by a jack — always use stands rated for your vehicle's weight.

What happens if I use the wrong oil weight?

Using oil that is too thick (like 10W-40 instead of 5W-30) can reduce fuel economy and make cold starts harder. Oil that is too thin may not protect the engine properly at high temperatures. Stick to what your manual specifies. If you accidentally use the wrong weight, you can change it at your next service interval — one oil change with the wrong weight will not damage the engine.

Do I need to replace the drain plug every time?

No. Reuse the same drain plug unless it is damaged, stripped, or leaking. If the threads are damaged or the plug is bent, replace it. A new plug costs $5 to $15 and is much cheaper than fixing an oil leak caused by a bad plug.