Training wheels on dirt bikes stabilize the rear wheel and lower the center of gravity to help new riders build balance and confidence before riding solo
Dirt bike training wheels are metal or plastic outriggers that bolt to the rear axle and touch the ground when the bike leans past a certain angle. They do not support the bike's full weight — instead, they catch the bike just before it tips over, letting the rider practice throttle control, braking, and steering without the fear of falling. Most training wheel kits engage around 15 to 25 degrees of lean, meaning the rider can still feel the bike working underneath them but cannot crash it over sideways.
Training wheels are not a substitute for instruction or protective gear. They work best for riders aged 4 to 10 on small-displacement bikes (50cc to 110cc), though some manufacturers make kits for larger machines. The goal is to use them for a few weeks or months, then remove them once the rider's muscle memory and confidence are solid enough to ride without a safety net.
Key Takeaways
- Training wheels bolt to the rear axle and engage only when the bike leans beyond a set angle, usually 15 to 25 degrees.
- They work best on bikes under 110cc and riders under 12 years old, though some kits fit larger machines.
- Training wheels cost between $150 and $400 depending on bike size and kit quality, and installation takes 30 minutes to an hour.
- Removing training wheels too early can cause crashes; most riders are ready after 4 to 8 weeks of regular practice.
- Training wheels do not replace a helmet, protective jacket, gloves, and boots — riders still need full gear even with wheels attached.
How training wheels physically attach and work
Training wheel kits come in two main designs: bolt-on kits that clamp to the existing rear axle, and weld-on frames that require permanent attachment to the bike's frame. Bolt-on kits are more common for consumer bikes because they are removable and do not damage the machine. The wheels themselves are small — usually 4 to 6 inches in diameter — and mounted on arms that swing down and outward as the bike tilts.
The angle at which the wheels engage is set by adjusting the length of the mounting arms or the position of the pivot point. A shorter arm means the wheels touch the ground sooner (lower lean angle), while a longer arm delays engagement (higher lean angle). Most kits come pre-set for a specific bike model, but you can fine-tune the angle by bending the arms slightly or adding spacers. The training wheels should barely kiss the ground when the bike is upright — if they are dragging during normal riding, the angle is set too low and the rider will not develop proper balance.
Choosing the right training wheel kit for your bike
Training wheel kits are model-specific because the rear axle diameter, frame geometry, and suspension travel vary widely between manufacturers. Before buying, confirm your bike's exact year, make, and model, then search for kits designed for that machine. Common brands include Pit Bike training wheel kits from manufacturers like Atomik and Stomp, which fit their own 50cc and 110cc models. For larger bikes, kits are harder to find and more expensive because fewer riders use them on machines over 125cc.
Check whether the kit is bolt-on or weld-on, and whether it includes all hardware and instructions. Some kits require you to remove the rear fender or mudguard to install the wheels, so read the installation guide before ordering. If your bike is not a common pit bike or small-displacement machine, you may need to contact a local shop to see whether they can fabricate or adapt a kit — this usually costs $200 to $400 in labor on top of the kit price.
Installation and setup
Bolt-on kits typically take 30 to 60 minutes to install if you have basic tools: a socket set, wrenches, and possibly a drill if the kit requires new mounting holes. Start by lifting the rear wheel off the ground using a stand or jack, then remove the rear axle nut on the side where you are installing the kit. Slide the training wheel bracket onto the axle, align it with the frame, and tighten the axle nut back down. Repeat on the other side if the kit includes two wheels.
Once both wheels are mounted, lower the bike and check that the wheels are parallel to each other and sit just barely off the ground when the bike is upright. If they are dragging, loosen the mounting bolts and rotate the bracket arms upward slightly, then re-tighten. Spin the rear wheel by hand to make sure it turns freely and the training wheels do not interfere. Take the bike to a flat, open area and have the rider sit on it while you watch the wheels — they should not touch the ground during normal riding, only when the bike leans significantly.
When to remove training wheels and signs the rider is ready
Most riders are ready to remove training wheels after 4 to 8 weeks of regular practice, usually 2 to 3 times per week. The signs of readiness are: the rider can start and stop without putting a foot down, can turn smoothly without jerking the handlebars, and can ride in a straight line without wobbling. If the rider is still touching down the training wheels on every turn or leaning the bike too far on straightaways, they need more time.
Remove the wheels gradually rather than all at once. Start by raising the engagement angle so the wheels only touch during extreme leans, then ride for another week or two. This forces the rider to develop better balance while still having a safety net. Once the rider is comfortable at the higher angle, unbolt one wheel and ride for a few sessions, then remove the other. Always supervise the first few rides without training wheels, and have the rider wear full protective gear including a helmet, jacket, gloves, and boots — crashes happen, and gear prevents serious injury.
Cost and where to buy training wheel kits
Training wheel kits for pit bikes and small-displacement dirt bikes range from $150 to $400, depending on the bike size and kit quality. Basic bolt-on kits for 50cc and 70cc machines typically cost $150 to $250, while kits for 110cc and larger bikes run $250 to $400. Weld-on kits are usually more expensive because they require professional installation, adding $200 to $400 in labor.
You can buy kits directly from pit bike manufacturers like Stomp, Atomik, and Thumpstar through their websites or authorized dealers. Amazon and eBay also carry generic kits, though quality varies — read reviews carefully and confirm the kit fits your exact bike model before ordering. Local motorcycle shops may stock kits or be able to order them, and some shops offer installation services if you do not want to bolt the kit on yourself.
Training wheels versus other learning methods
Training wheels are one tool among several for teaching young riders. Other methods include riding with a spotter who holds the bike steady, using a tether or rope attached to the frame, or straightforward practicing on a very small, lightweight bike that is straightforward to pick up after a fall. Training wheels have the advantage of being hands-free — the spotter does not need to run alongside the bike — and they work continuously without tiring. The downside is that they can create a false sense of security if left on too long, and some riders become dependent on them and struggle when they are removed.
The best approach combines training wheels with instruction. A may have access to instructor can teach the rider proper body position, throttle control, and braking technique while the training wheels prevent crashes from balance mistakes. Once the rider has the fundamentals down, the wheels come off and the rider applies those skills with real balance challenges. Training wheels alone, without instruction or practice, will not produce a confident rider.
Frequently Asked Questions
Can I use training wheels on a full-size dirt bike?
Training wheel kits exist for bikes up to about 250cc, but they are rare and expensive because most adult riders do not use them. If your bike is larger than 125cc, contact a local fabrication shop — they can often adapt a pit bike kit or build a custom frame. Expect to pay $300 to $600 in labor plus the kit cost.
Do training wheels slow down the bike or affect handling?
Training wheels add a small amount of weight and drag, but the effect is minimal on a small dirt bike. The real impact is psychological — riders sometimes lean on the wheels instead of developing balance. Set the engagement angle high enough that the wheels only touch during extreme leans, and the rider will still develop proper technique.
What if my child is afraid to ride without training wheels?
Fear is normal. Remove the wheels gradually by raising the engagement angle first, so the rider experiences riding without the wheels touching but still knows they are there. Practice in a large, flat, obstacle-free area with no traffic. Have the rider wear full protective gear so they feel confident that a fall will not hurt them badly.
Can training wheels damage the bike's frame or axle?
Bolt-on kits do not damage the frame or axle if installed correctly. Weld-on kits create permanent attachment points, so removing them later leaves holes or scars. Always use bolt-on kits if you plan to remove the training wheels later or sell the bike.
How do I know if the training wheels are set at the right angle?
The wheels should barely touch the ground when the bike is upright and parked on flat ground. During normal riding on flat terrain, they should not touch at all. Only during sharp turns or extreme leans should the wheels engage. If they are dragging during straight-line riding, raise the mounting arms or adjust the pivot point to delay engagement.