What crating a small block Chevy means and when you need it

Crating a small block Chevy means securing the engine in a wooden or metal box for storage, shipping, or transport. The crate protects the engine from dirt, moisture, and physical damage during handling. You'll need this if you're storing an engine long-term, sending it to a machine shop across the state, selling it, or moving it to a new vehicle.

A properly crated engine arrives without rust on internal surfaces, without loose bolts rattling free, and without damage to the block or heads. The difference between a crate that works and one that doesn't shows up weeks or months later—when you pull the engine out and find water inside the block or a cracked casting from shifting during transport.

Key Takeaways

  • A small block Chevy crate must be wooden or metal, sealed against moisture, and braced so the engine cannot shift during transport or storage.
  • Remove the carburetor, intake manifold, and any loose external parts before crating, and plug all openings to keep moisture and debris out of the block.
  • The engine should sit on wooden blocks or a steel frame inside the crate, with the weight distributed evenly and braced on all sides.
  • Wrap the entire engine in plastic sheeting or use a moisture barrier before closing the crate, and store it in a dry location away from direct sunlight.
  • Crating costs between $200 and $800 depending on whether you build it yourself or pay a shop, and takes one to three days if you do it by hand.

Preparing the engine before it goes in the crate

Start by removing anything that can shift, vibrate loose, or trap moisture. Take off the carburetor or fuel injection system, the intake manifold, the alternator, the water pump, and the fan. These parts travel separately or get wrapped individually. Leave the block, heads, pan, and core components in place—those are what the crate is built around.

Drain the oil completely and leave the drain plug out so any remaining oil can drip away. If coolant is still in the block, drain that too. Wipe down the exterior with a clean rag to remove loose dirt and old grease. Plug every opening: the carburetor opening, the intake ports, the distributor hole, the oil filler cap hole, and the water jacket openings. Use rubber caps, wooden dowels, or tape—anything that keeps moisture and insects out.

If the engine has been sitting for months or years, turn it over by hand a few times using a breaker bar on the harmonic balancer. This breaks any corrosion inside the cylinders and moves oil around. Do not start it; you're just loosening things up so the engine doesn't seize during transport.

Building or sourcing the crate itself

A crate can be wood or steel. Wood is cheaper and easier to build yourself; steel is stronger and reusable. For a small block Chevy, a wooden crate is usually 36 inches long, 24 inches wide, and 24 inches tall—large enough to hold the engine with a few inches of clearance on all sides.

If you're building it, use 2-by-4 lumber for the frame and 3/4-inch plywood for the sides. Bolt or screw the corners together so they won't come apart. The crate must be rigid enough that it doesn't flex when lifted by a forklift or moved on a pallet. Reinforce the bottom with extra 2-by-4s running lengthwise, spaced 12 inches apart. These become the mounting points for the engine.

If you're buying a pre-made crate, check that it has drain holes in the bottom (so water doesn't pool), ventilation holes to prevent condensation buildup, and a lid that seals tightly. Some machine shops and engine builders sell crates designed specifically for small block Chevys and will crate the engine for you as part of a rebuild or sale.

Mounting and bracing the engine inside the crate

Set the engine on wooden blocks or a steel frame bolted to the bottom of the crate. The engine should sit 4 to 6 inches above the crate floor so air can flow underneath and water won't pool around the pan. Use at least four mounting points—one near each corner of the block—and bolt them down tight.

Brace the engine on all four sides using 2-by-4s or steel angle iron. The braces should be snug but not so tight they bend the block or heads. Leave about 1/2 inch of clearance between the engine and each brace. Bolt the braces to the crate frame, not to the engine itself. The goal is to prevent any movement if the crate is dropped, tilted, or jostled during loading or transport.

Check that the engine cannot rock forward, backward, left, or right. Grab the block with both hands and try to move it. If it shifts at all, tighten the braces or add more. A small block Chevy weighs 550 to 650 pounds depending on what's still attached, so the bracing has to hold that weight stable.

Sealing and protecting against moisture

Wrap the entire engine in plastic sheeting or heavy-duty plastic wrap before closing the crate. This creates a moisture barrier and keeps dust off the block. Overlap the plastic by at least 6 inches at every seam and tape it down with duct tape or packing tape. If you're storing the crate outdoors or in an unheated space, use a thicker plastic or add a second layer.

Some builders use silica gel packets or desiccant packs inside the crate to absorb moisture. Place these in the corners or on top of the engine, away from any moving parts. Replace them every few months if the engine will be in storage for more than six months.

Close the crate lid and seal all seams with caulk or weatherstripping tape. Label the crate clearly: "Engine—Do Not Drop," "This Side Up," and the engine size and year. Include your contact information in case the crate is damaged in transit and the carrier needs to reach you.

Storage and transport considerations

Store the crate indoors if possible—in a garage, warehouse, or climate-controlled space. If it must stay outside, build a straightforward roof over it or cover it with a tarp, but leave the sides open to air. Moisture trapped under a sealed tarp will rust the engine faster than open air.

Keep the crate off the ground using wooden pallets or concrete blocks. This prevents water from pooling underneath and allows air to circulate. Check the crate every few months, especially if it's been raining or if the storage space is damp. If you see condensation on the plastic, open the crate briefly to let it dry out, then reseal it.

For transport, use a flatbed truck or enclosed trailer. find the crate with straps or chains so it cannot slide or tip. If the crate is being shipped by freight company, make sure the carrier knows it contains an engine and will handle it accordingly. Many freight companies charge extra for heavy or fragile items, so ask about that before booking.

Cost and timeline for crating

If you build the crate yourself using lumber you source locally, the materials cost between $150 and $300. If you buy a pre-made crate, expect to pay $300 to $600. If you have a machine shop or engine builder crate the engine for you, the labor runs $200 to $500 depending on how much prep work they do.

Building and crating the engine yourself takes one to three days if you work alone and have basic tools. Most of that time is spent removing external parts, building or assembling the crate, and bracing the engine. If you're paying a shop, the turnaround is usually one to two weeks, though it can be faster if they have a crate ready and you drop the engine off prepped.

Frequently Asked Questions

Can I crate a small block Chevy with the carburetor still attached?

You can, but it's not recommended. The carburetor can crack if the crate is tilted or dropped, and fuel residue inside it can gum up during storage. Remove it, wrap it separately, and pack it in a box with the other small parts. This also makes the engine lighter and easier to brace inside the crate.

How long can a crated engine sit in storage without problems?

A properly crated and sealed engine can sit for years without rust or damage if stored in a dry location. The key is keeping moisture out and checking on it every few months. If you're storing it longer than a year, replace the desiccant packs every six months and inspect the plastic wrap for tears.

Do I need to drain the coolant before crating?

Yes. Coolant left in the block can freeze in winter and crack the casting, or it can settle and corrode internal passages during long storage. Drain it completely and leave the drain plugs out so the block can dry. You can refill it when the engine is installed in its new home.

What if the crate gets wet during transport?

If water gets inside the crate, open it as soon as possible and let the engine dry. Wipe down the block and heads with a clean rag, and run a fan or air compressor over it to dry the hard-to-reach spots. If water got inside the block itself (which shouldn't happen if you plugged the openings), you may need to pull the pan and drain it before storage continues.

Can I use a cardboard box instead of wood or metal?

No. Cardboard will collapse under the weight of a small block Chevy and offers no protection from moisture or impact. Stick with wood or steel. If cost is a concern, a basic wooden crate made from 2-by-4s and plywood is the cheapest option and will last through multiple uses.