What the Bush Hog 50074580 part does and where it fits
The Bush Hog 50074580 is a gearbox input shaft seal used in Bush Hog rotary cutters and finish mowers. This seal prevents hydraulic fluid from leaking out of the gearbox where the input shaft enters the housing. If you see oil pooling under your mower or notice the gearbox running low on fluid between services, a worn seal is often the culprit.
This part number appears in Bush Hog's parts catalogs for several models of mid-sized rotary cutters, though the exact machines that use it vary by year and configuration. Before ordering, you need to confirm your specific mower model matches this part number in your owner's manual or parts diagram.
Replacing a gearbox seal is a moderate-difficulty job. You will need to drain the gearbox, remove the input shaft, and press out the old seal — work that most owners can do with basic tools, though some prefer to send the gearbox to a shop. The part itself costs less than the labor if you go that route.
Key Takeaways
- The 50074580 is a gearbox input shaft seal that stops hydraulic fluid from leaking where the shaft enters the gearbox housing.
- You must confirm this part number matches your mower model before ordering, because Bush Hog uses different seals across their product line.
- Replacement requires draining the gearbox, removing the input shaft, and pressing out the old seal — a task most owners can handle with hand tools and a shop press or bearing puller.
- You can order this part from Bush Hog dealers, online equipment suppliers, or general farm equipment distributors that stock Bush Hog components.
How to verify this is the right part for your mower
Start with your owner's manual or the parts diagram that came with your mower. Look up your specific model number and year, then find the gearbox section. The diagram should show the input shaft seal and its part number. If the number matches 50074580, you have the right part.
If you no longer have the manual, contact a Bush Hog dealer with your mower's model and serial number. They can pull up the parts diagram in their system and confirm whether this seal is correct for your machine. Many dealers will do this over the phone or email at no cost.
A third option is to remove the gearbox input shaft yourself and take the old seal to a dealer or farm equipment supplier. They can match it visually and confirm the part number. This takes more time but removes all doubt before you buy.
Where to order the 50074580 seal
Bush Hog dealers are the most direct source. Search online for "Bush Hog dealer near me" or call the Bush Hog customer service line to find an authorized dealer in your area. Dealers typically stock common seals or can order them within a few days. Prices vary by location, but expect to pay between $15 and $40 for the seal itself.
Online farm equipment suppliers like Tractor Supply, Messick's, and Hy-Capacity carry Bush Hog parts and often have the 50074580 in stock. These sites let you search by part number and show availability before you buy. Shipping usually takes three to seven business days.
General equipment distributors and industrial supply shops that serve farmers may also stock this seal or order it from their Bush Hog distributor. Call ahead to confirm they carry it, since smaller shops may not keep every seal on hand.
Tools and materials you will need to replace the seal
To do the job yourself, gather a drain pan, wrenches or sockets that fit your gearbox bolts, a seal removal tool or bearing puller, a seal installation tool or socket that matches the seal's outer diameter, and a shop press or arbor press. If you do not have a press, a bearing puller and careful hammer work can remove the old seal, though a press makes the job cleaner and safer.
You will also need fresh hydraulic fluid to refill the gearbox after you finish. Check your mower's manual for the correct fluid type and viscosity — using the wrong fluid can damage the gearbox. Have a clean rag and a small brush on hand to clean the shaft and housing before installing the new seal.
If you lack a press or removal tools, many farm equipment shops will rent or loan these items, or you can pay them to do the seal replacement for you. The labor cost is usually $50 to $150 depending on how accessible the gearbox is on your model.
Step-by-step replacement process
First, park the mower on level ground and let the gearbox cool if it has been running. Locate the gearbox drain plug — usually on the bottom or side of the housing — and remove it. Let the hydraulic fluid drain completely into your pan. This can take 10 to 15 minutes.
Next, unbolt the gearbox input shaft coupling or the shaft itself, depending on your mower's design. You may need to remove a guard or other components to access the bolts. Keep track of which bolts go where, since they may be different sizes.
Once the shaft is free, use your seal removal tool or bearing puller to extract the old seal from the gearbox housing. Work slowly and evenly to avoid damaging the shaft or the bore where the seal sits. Clean the shaft and the bore with a rag and inspect both for scoring or wear. If the shaft is deeply scratched, the new seal may not hold.
Install the new seal by pressing it straight into the bore using your seal installation tool or a socket that matches the seal's outer diameter. A shop press makes this step straightforward — align the seal and press it in until it seats fully. If you are using a hammer and socket, tap gently and evenly around the seal's edge to avoid cocking it.
Reinstall the input shaft, reconnect the coupling, and refill the gearbox with the correct hydraulic fluid to the proper level. Run the mower briefly at idle to circulate the new fluid, then check for leaks around the seal. If fluid seeps out, stop when ready and inspect your work.
Common mistakes that lead to seal failure
Installing the seal backward is the most common error. The seal's spring and lip face inward, toward the gearbox fluid. If you press it in the wrong direction, it will leak when ready. Check your old seal's orientation before you remove it, or look at the diagram in your parts manual.
Cocking the seal during installation — pressing it in at an angle — damages the lip and causes leaks. Use a proper seal installation tool or a socket that is the same diameter as the seal's outer edge. This keeps the seal straight as it goes in.
Overfilling the gearbox with hydraulic fluid puts pressure on the seal and can blow it out. Fill to the level mark on the dipstick or sight glass, not higher. Too much fluid also causes the gearbox to run hot, which shortens seal life.
Reusing the old seal or installing a damaged seal will fail within weeks. Always install a new seal, and inspect the shaft for scoring. If the shaft is worn, a new seal will not hold — you may need to have the shaft replaced or resurfaced.
When to call a professional instead
If your gearbox is difficult to access — buried under the mower deck or welded into a tight space — a shop can do the work faster and with less risk of dropping bolts or tools into hard-to-reach spots. The labor cost is usually worth the time saved.
If the shaft is scored or worn, or if you discover damage to the gearbox bore while the seal is out, a shop has the equipment to assess whether the shaft can be resurfaced or needs replacement. Attempting this yourself without the right tools can make the problem worse.
If you do not have access to a shop press or seal removal tools, renting them may cost as much as paying a shop to do the job. Many farm equipment dealers offer seal replacement as a routine service and can often fit you in within a week.
Frequently Asked Questions
How do I know if my gearbox seal is leaking?
Look under your mower after it has been parked for an hour or two. Fresh oil spots or a puddle under the gearbox input shaft area indicate a leaking seal. You may also notice the gearbox fluid level dropping between regular checks, or see oil on the outside of the gearbox housing near the shaft.
Can I replace the seal without draining the gearbox?
No. Draining the gearbox is essential because it prevents fluid from spilling when you remove the input shaft and gives you a clean work area. Attempting the job without draining will result in a mess and makes it harder to see what you are doing.
What if the new seal leaks right after I install it?
Stop using the mower when ready and check your work. The seal may be installed backward, cocked at an angle, or not fully seated. Remove it and inspect the shaft and bore for damage. If both look clean, reinstall the seal carefully, making sure it goes in straight and fully.
How long does a gearbox seal usually last?
A properly installed seal on a well-maintained gearbox typically lasts several years or hundreds of hours of mowing. Seals fail faster if the gearbox runs hot, is overfilled, or if the shaft is worn. Regular fluid checks and prompt replacement of a leaking seal prevent larger gearbox damage.
Is the 50074580 seal the same for all Bush Hog models?
No. Bush Hog uses different seals across their product line depending on gearbox size and design. Always confirm the part number in your mower's manual or with a dealer before ordering. Installing the wrong seal will not fit or will leak.