The BRZ motion ratio is the mathematical relationship between how far your suspension moves and how far the wheel actually travels, expressed as a decimal or ratio
The motion ratio on a Subaru BRZ (and most cars) describes how much the suspension compresses or extends compared to the wheel's vertical movement. If your wheel moves up one inch, the suspension linkage might compress only 0.8 inches — that 0.8 is your motion ratio. It's not a single number you'll find on a spec sheet; it changes depending on suspension geometry and where in the suspension's travel range you measure it.
Understanding this matters because it affects how stiff your springs need to be, how the car responds to bumps, and how much force the suspension components actually experience. A lower motion ratio means the suspension moves less than the wheel, which effectively makes your springs feel stiffer without actually being stiffer. A higher ratio means the opposite.
Key Takeaways
- Motion ratio is the ratio of suspension travel to wheel travel, and it varies throughout the suspension's range of motion on a BRZ.
- A lower motion ratio makes springs feel stiffer and reduces the force on suspension components; a higher ratio does the opposite.
- The BRZ's double-wishbone front and double-wishbone rear suspension geometry creates a motion ratio that changes as the suspension compresses.
- Tuners adjust spring rates and dampers based on motion ratio to achieve the handling balance they want without over-stressing parts.
- You don't need to calculate motion ratio yourself — suspension shops and tuning guides for the BRZ already account for it in their recommendations.
How the BRZ suspension geometry creates its motion ratio
The BRZ uses a double-wishbone suspension at both the front and rear, which means the motion ratio is determined by the angles and lengths of the control arms. As the suspension moves through its travel, the geometry changes slightly, so the motion ratio is not constant — it's higher at full droop (suspension fully extended) and lower at full compression.
At the front, the lower control arm is longer than the upper one, which creates a motion ratio somewhere in the range of 0.85 to 0.95 depending on where in the travel you measure. At the rear, the geometry is similar, producing a comparable range. This means the wheel moves more than the suspension linkage does, which is typical for most road cars.
The practical effect is that a BRZ spring doesn't need to be as stiff as the wheel rate (the stiffness felt at the tire) would suggest. If you want a wheel rate of 200 lb/in, you might only need a spring rate of around 170 to 180 lb/in, because the motion ratio multiplies the spring's effect.
Spring rate, wheel rate, and why motion ratio connects them
The spring rate is how stiff the coil spring itself is, measured in pounds per inch of compression. The wheel rate is the stiffness you feel at the tire — how much force it takes to push the wheel down one inch. Motion ratio is what converts one to the other.
The formula is: wheel rate = spring rate ÷ (motion ratio)². If your BRZ has a spring rate of 180 lb/in and a motion ratio of 0.9, the wheel rate is 180 ÷ (0.9)² = 180 ÷ 0.81 = about 222 lb/in. This is why a lower motion ratio effectively stiffens the suspension without requiring a stiffer spring — the math amplifies the spring's effect.
When you're shopping for coilovers or springs for a BRZ, tuning guides and manufacturers already factor this in. They list spring rates that account for the motion ratio, so you don't have to do the math yourself. But understanding the relationship helps you see why different suspension setups feel different even if the spring rates look similar on paper.
How motion ratio affects suspension forces and component wear
A lower motion ratio doesn't just make the suspension feel stiffer — it also reduces the actual force that the suspension components experience. Because the suspension linkage moves less than the wheel, the forces are mechanically reduced by the motion ratio squared, just like the spring rate is.
This is one reason why double-wishbone suspensions are common on performance cars: they allow for a favorable motion ratio that keeps component stresses manageable while still delivering the stiffness and control the driver wants. If the suspension linkage moved one-to-one with the wheel, the same spring rate would create much higher forces on the control arms, ball joints, and bushings.
Over time, this matters for durability. A suspension tuned with motion ratio in mind will wear more evenly and last longer than one where the geometry and spring rates are mismatched. This is why BRZ owners who upgrade to coilovers should stick with setups designed for the BRZ rather than adapting springs and rates from other cars.
Motion ratio in tuning and performance driving
Track-focused BRZ builds often involve adjusting spring rates, damper settings, and sometimes even suspension geometry to optimize the motion ratio for a specific driving style or track. A stiffer setup might use springs that are stiff enough to keep the car from diving under braking, while the motion ratio ensures the suspension doesn't bind up or create excessive loads.
Lowering the car changes the motion ratio slightly because it alters the angles of the control arms. A BRZ that's lowered 1.5 inches will have a slightly different motion ratio than stock, which is why suspension shops sometimes recommend adjusting spring rates when you lower a car — not just because it looks better, but because the geometry has shifted.
For street driving, you don't need to think about motion ratio at all. But if you're modifying your BRZ's suspension or comparing different coilover options, knowing that motion ratio exists and how it works will help you understand why one setup feels different from another and why the numbers on a spec sheet don't tell the whole story.
Finding motion ratio data for your BRZ
Subaru doesn't publish motion ratio figures in the owner's manual or standard service documentation. If you need exact numbers for your model year and suspension configuration, your best sources are dedicated BRZ forums, suspension tuning guides, and aftermarket suspension manufacturers who publish technical specs for their products.
Many coilover and spring manufacturers for the BRZ include motion ratio calculations in their setup guides or technical documentation. If you're working with a suspension shop that specializes in BRZ tuning, they'll have this data on hand and can explain how it affects the recommendations they're making for your car.
You can also calculate motion ratio yourself if you have the suspension geometry — the lengths and angles of the control arms — but this requires careful measurement and some trigonometry. For most owners, it's easier to rely on existing data from manufacturers and tuning communities who have already done the work.
Frequently Asked Questions
Does a higher motion ratio mean a stiffer suspension?
No — a higher motion ratio means the suspension moves more relative to the wheel, which makes springs feel softer. A lower motion ratio makes springs feel stiffer because the suspension moves less. The relationship is inverse: lower motion ratio = stiffer feel, higher motion ratio = softer feel.
Will lowering my BRZ change the motion ratio?
Yes, slightly. Lowering the car changes the angles of the control arms, which shifts the motion ratio. The change is usually small enough that you don't need to recalculate spring rates, but extreme lowering or suspension modifications can make the difference noticeable.
Can I use springs from another car on my BRZ if I adjust for motion ratio?
Not reliably. Different cars have different motion ratios, and even if you calculate the correct spring rate, the suspension geometry and mounting points are different. Stick with springs and coilovers designed for the BRZ to avoid binding, poor handling, or premature wear.
Why does my coilover setup guide mention motion ratio?
Because the manufacturer has already accounted for the BRZ's motion ratio when recommending spring rates. They're telling you the spring rate is correct for the car's geometry — you don't need to adjust it further based on motion ratio calculations.