What Aurora AFX slot car tracks are and why people still use them
Aurora AFX is a brand of slot car racing system that has been around since the 1960s. The track consists of a groove-based plastic roadway where small electric cars run on guide pins, powered by electrical current flowing through the track itself. Unlike modern digital systems, AFX uses a straightforward two-lane analog setup where each car draws power from its own lane, and speed is controlled by how hard you press the hand controller trigger.
People still buy and build Aurora AFX tracks today because they are affordable, durable, and require no computer setup. A used AFX track set can cost between $30 and $150 depending on condition and how many pieces you have. The cars themselves are inexpensive and straightforward to repair or modify. If you are looking for a hobby that does not demand a lot of space or money upfront, or if you inherited a track from someone and want to know whether it still works, understanding how AFX operates will help you decide whether to invest time in it.
Key Takeaways
- Aurora AFX tracks use a straightforward groove-and-pin system where two cars race side by side on separate lanes powered by the track itself.
- The hand controller is a variable resistor that lets you control speed by squeezing the trigger, with no lap counting or digital features.
- Track pieces are modular plastic sections that snap together, and the electrical connections are made through metal tabs on the underside of each piece.
- Common problems include dirty track grooves, worn guide pins on cars, and loose electrical connections, all of which can be fixed with basic cleaning and replacement parts.
- AFX track and car parts are still manufactured and sold by hobby retailers, though selection is smaller than it was in the 1980s and 1990s.
How the track layout and electrical system work
An Aurora AFX track is made up of plastic sections that lock together to form a closed loop. Each section has two parallel grooves running down the center, one for each racer. The grooves are not just for show — they hold a guide pin on the underside of each car, keeping it centered in its lane. Without the guide pin, the car would slide sideways and crash into the wall or the other car.
Power flows through metal tabs on the underside of each track section. When you connect a power supply to the transformer (the box that plugs into the wall), electricity travels through the track pieces in a continuous circuit. Each lane has its own electrical path, so both cars can run at the same time without interfering with each other. The hand controller sits between you and the transformer and acts as a variable resistor — when you squeeze the trigger, you reduce the resistance and send more power to the motor in your car, making it go faster. Release the trigger and the car slows down.
This is why AFX racing feels different from modern slot car systems: you have direct, continuous control over your speed, but you cannot program pit stops, change lanes, or use lap counters. What you see is what you get.
Checking whether your track still works
If you have an Aurora AFX track that has been sitting in storage, start by inspecting the track pieces for visible damage. Look for cracks in the plastic, especially around the groove area, and check that the metal tabs on the underside are not bent or corroded. Gently try to snap two pieces together — they should lock firmly without forcing.
Next, clean the grooves with a soft brush or cloth. Dirt and dust buildup is the most common reason an old track stops working properly. Wipe the metal tabs and the underside of each piece with a dry cloth to remove any corrosion or debris. If the tabs look heavily oxidized (dark or discolored), you can gently rub them with a pencil eraser or fine steel wool to restore electrical contact.
Once the track is clean, assemble a small section — just two or three pieces — and plug in the transformer. Listen for a hum from the power supply. If you hear it, power is reaching the track. Place a car on the track and squeeze the controller trigger. If the car moves, your basic system is working. If it does not move or moves only in one lane, you likely have a loose connection or a bad controller.
Common problems and how to fix them
The most frequent issue with older AFX tracks is a car that will not stay in its lane or keeps derailing. This usually means the guide pin is worn flat or broken. Guide pins are small plastic or metal pieces that stick down from the car and ride in the track groove. You can buy replacement guide pins from hobby retailers for a few dollars. Removing the old pin usually requires opening the car body — most AFX cars have a clip or screw that holds the chassis together — and then unclipping or unsoldering the old pin and installing a new one.
If both cars are running but one is much slower than the other, check the controller that is connected to the slow car. Hand controllers wear out over time, and the trigger mechanism can become stiff or unreliable. You can test this by swapping controllers between the two lanes — if the slow car suddenly runs fast with the other controller, you have found your problem. Replacement controllers cost between $10 and $25.
If neither car is running, check that all track sections are snapped together tightly and that the metal tabs are making good contact. A single loose connection can break the entire circuit. Unplug the transformer, reseat every connection, and plug it back in. If you still have no power, the transformer itself may be dead — these can fail after decades of use, and replacements are available from hobby shops.
Upgrading and modifying your track
One advantage of Aurora AFX is that the system is straightforward enough to modify without special tools or knowledge. Many hobbyists upgrade their cars by replacing the motor with a faster one, adding weight to improve traction, or sanding the guide pin to fit the groove more precisely. Track modifications are less common but possible — some people add banked curves or build elevated sections using wooden supports underneath.
If you want to expand your track, AFX pieces are still sold as individual sections or in starter sets. A basic set includes a power supply, two controllers, two cars, and enough track to make a straightforward oval loop. Adding more track pieces lets you build more complex layouts with straightaways, curves, and chicanes. Most hobby retailers that carry slot car equipment stock AFX pieces, though selection may be smaller than for newer systems like Carrera or Scalextric.
Before you invest in upgrades, decide what you want from the hobby. If you are racing casually with friends or family, the stock setup is fine. If you want to compete or build a large permanent track, you may find that the simplicity of AFX becomes a limitation — you cannot program race modes, set handicaps, or count laps automatically.
Where to find parts and support
Aurora AFX parts are still manufactured and sold, though the market is smaller than it was decades ago. Online retailers like Slot Car Corner, Slot Car Garage, and eBay have new and used AFX track sections, cars, motors, controllers, and accessories. Local hobby shops that carry model trains or slot cars often stock AFX items or can order them for you.
For technical questions or repair information, slot car forums and Facebook groups dedicated to classic slot car racing are active and helpful. Many members have been running AFX tracks since the 1970s and can walk you through troubleshooting or modification projects. YouTube also has videos showing how to disassemble AFX cars, replace guide pins, and build custom track layouts.
If you are looking for rare or vintage AFX pieces, eBay and specialty slot car auction sites are your best bet, though prices for collectible items can be high. For everyday parts like replacement motors, guide pins, and controllers, expect to pay between $5 and $30 per item.
Frequently Asked Questions
Can I use Aurora AFX cars on other slot car tracks?
No. AFX cars have a specific guide pin design and electrical connector that only work with AFX track. Other systems like Carrera, Scalextric, and Tyco use different groove widths and pin designs. You would need to buy cars designed for the track system you own.
How fast do Aurora AFX cars go?
Stock AFX cars typically reach speeds of 8 to 12 miles per hour on the track. With motor upgrades and modifications, some hobbyists have pushed them faster, but the track design limits how much speed is practical. The appeal of AFX is the racing experience, not raw speed.
What power supply do I need for an Aurora AFX track?
Most AFX systems use a transformer that plugs into a standard wall outlet and outputs between 12 and 18 volts DC. If you have lost your original transformer, you can buy a replacement from hobby retailers. Make sure it is rated for slot car use — a generic power supply may not have the right voltage or safety features.
Is Aurora AFX still made by the original company?
Aurora Plastics, the original manufacturer, stopped making AFX in the 1990s. The brand and tooling were sold to other companies over the years. Today, AFX products are made under license by manufacturers like Tomy and sold through hobby retailers. The track and car designs remain largely unchanged from the original.
Can I repair a cracked track piece?
Small cracks in the plastic can sometimes be glued with plastic cement or epoxy, but if the crack runs through the groove or the metal tab area, repair is usually not reliable. Replacement pieces are inexpensive enough that buying new sections is often the better choice. A single track piece typically costs $5 to $15.