What an AMP Research PowerStep is and whether you can install it yourself

An AMP Research PowerStep is an electric running board that deploys automatically when you open your truck door and retracts when you close it. The board extends about 12 inches outward from the rocker panel, giving you a wider step to climb into a lifted truck without needing a permanent bolt-on board or step stool.

Installation is a bolt-on job that takes 2 to 4 hours and requires basic hand tools — no welding, cutting, or drilling into the frame. Most truck owners with mechanical experience can do it in a driveway. If you've never worked on a vehicle before, you'll want to budget for a shop to handle it, which typically costs $300 to $600 in labor on top of the board's price.

The board itself mounts to the existing rocker panel and frame using the factory bolt holes or new holes drilled into non-structural areas. Wiring connects to your door latch switches and a 12-volt power source under the hood or inside the cab. The hardest part is usually running the wiring cleanly and making sure the board deploys and retracts smoothly without binding.

Key Takeaways

  • PowerStep installation requires removing the wheel well liner, drilling a few holes in the rocker panel, and bolting the mounting brackets to the frame — a job most DIY truck owners can complete in an afternoon.
  • Wiring the board to your door latch switches and power source is straightforward but time-consuming; the instructions walk you through which wires to tap into under the dash.
  • You'll need a drill, socket set, screwdrivers, wire strippers, and a multimeter to test power; most people already own these tools.
  • The board must be programmed or adjusted so it deploys only when the door opens and retracts fully when the door closes, or it will drag on the ground or fail to extend.
  • If you're uncomfortable drilling into your truck or running wiring, a professional installation is worth the cost to avoid damaging the rocker panel or creating electrical gremlins.

Tools and parts you'll need before starting

AMP Research sells PowerStep kits specific to your truck model and year — the brackets and wiring harness are different for a 2019 Ford F-150 than a 2015 Chevy Silverado. Order the correct kit for your truck before you begin. The kit includes the board itself, mounting brackets, fasteners, and a wiring harness with connectors.

For tools, gather a cordless drill with a 1/4-inch bit, a socket set (10mm through 18mm covers most fasteners), a screwdriver set, wire strippers, a multimeter, and a flashlight. You'll also need a jack and jack stands if you need to lift the truck to access the rocker panel bolts, though many installations don't require it. A trim removal tool helps pop off the wheel well liner without cracking it.

Set aside 3 to 4 hours and work in a well-lit space — a garage is ideal, but a driveway works if you have good lighting. Have the truck's service manual or the PowerStep instruction sheet nearby; the wiring diagram shows exactly which wires under the dash control the door latch switches.

Removing the wheel well liner and preparing the rocker panel

Start by opening the driver's side door and removing the wheel well liner. This plastic panel covers the inside of the wheel well and is held on with plastic clips and a few bolts. Pop the clips with a trim tool and unbolt the panel, then set it aside — you'll reinstall it later.

Next, locate the rocker panel mounting points. The PowerStep brackets bolt to the frame just below the rocker panel, using existing factory holes or new holes you'll drill. Check the instruction sheet for the exact location on your truck model. If you're drilling new holes, mark them with a marker and use a center punch to keep the drill bit from walking. Drill slowly with a 1/4-inch bit and wear safety glasses — metal shavings will fly.

Clean away any dirt or rust from the mounting area with a wire brush. If the rocker panel is heavily rusted, sand it lightly so the brackets sit flush. Misaligned brackets cause the board to bind when it extends or retracts, so take time to get this right.

Bolting the mounting brackets and board to the frame

Slide the mounting brackets into position and hand-tighten the bolts first. Don't torque them down yet — you need to check that the board will clear the ground and deploy smoothly. Tighten the bolts gradually in a crisscross pattern (like tightening wheel lugs) so the bracket sits evenly.

Once the brackets are bolted down, attach the PowerStep board itself to the brackets using the fasteners included in the kit. Again, hand-tighten first and check that the board is level and doesn't rub against the tire or fender. The board should sit about 2 to 3 inches above the ground when retracted. If it's too low, you may have drilled the holes in the wrong spot — loosen the bolts and adjust.

After everything is bolted tight, manually push and pull the board to make sure it moves freely. It should slide in and out smoothly without grinding or catching. If it binds, loosen the bolts slightly and realign the brackets. Once it moves freely, torque all bolts to the specification in the instruction sheet — usually 18 to 25 foot-pounds for rocker panel bolts.

Running wiring from the door latch switches to the board

The PowerStep needs power and a signal to know when to deploy. Power comes from your truck's battery (usually a 12-volt line under the hood or inside the cab). The deployment signal comes from the door latch switches — when you open the door, the switch closes and tells the board to extend.

Locate the door latch switch wires under the driver's side dash. The instruction sheet shows which wires to tap into. Use a multimeter to confirm you have power and ground before cutting into any wires. Strip about 1/2 inch of insulation from the door latch wire and the PowerStep harness wire, then twist them together and cover the connection with a butt connector and crimp it tight with a crimper. Electrical tape alone is not enough — use proper connectors.

Run the main power wire from the battery to the PowerStep control module (usually mounted under the seat or inside the door jamb). Use a fused power line — the kit includes a fuse holder and fuse, which protects the wiring from a short circuit. Route the wires along existing harnesses under the truck to keep them out of sight and away from moving parts. find them with zip ties every 12 inches or so.

Testing deployment and programming the board

Before you close up the wheel well liner, test the board. Turn on the ignition and open the driver's side door — the board should extend smoothly. Close the door and it should retract. If it doesn't move, check that the power wire is connected to the battery and the door latch wire is properly crimped.

Some PowerStep models require programming or adjustment so the board deploys only when the door opens and doesn't extend while driving. Check the instruction sheet for your model — you may need to hold down a button on the control module while opening and closing the door a few times to "teach" it the correct timing. This step is straightforward but straightforward to miss, and skipping it can cause the board to deploy unexpectedly while you're driving.

Test the board 10 to 15 times in a row to make sure it's reliable. If it stalls partway through or retracts slowly, the motor may not be getting enough power — check that the battery connection is tight and the fuse hasn't blown. If the fuse blows repeatedly, there's a short in the wiring and you need to find it before driving the truck.

Reinstalling the wheel well liner and final checks

Once the board is working smoothly, reinstall the wheel well liner. Line up the bolt holes and clips, then hand-tighten the bolts. Make sure the liner doesn't interfere with the board when it extends — there should be at least 1/2 inch of clearance. Tighten the bolts fully and snap the clips back into place.

Do a final walk-around. Open and close the door 5 to 10 times and watch the board deploy and retract from outside the truck. Listen for grinding or squeaking — these sounds mean something is rubbing or binding. Check that the board doesn't hit the tire, fender, or ground at any point in its travel. If everything looks and sounds good, you're done.

Drive the truck slowly around the block and listen for any new noises. The board should not deploy while you're driving — if it does, the door latch switch wiring is loose or the programming didn't take. Pull over and check the connections under the dash.

Frequently Asked Questions

Can I install a PowerStep on a truck that's already lifted?

Yes, but you may need to adjust the mounting height so the board doesn't drag on the ground when retracted. Lifted trucks sit higher, so the rocker panel is further from the ground. The PowerStep brackets have some adjustment range — check the instruction sheet for your truck's lift height and adjust accordingly.

What happens if the board gets stuck halfway out?

The motor will stall and the board will stop moving. This usually means the power connection is loose, the fuse has blown, or something is physically blocking the board. Check the battery connection first, then the fuse, then manually push the board to see if it moves freely. If it's stuck, loosen the mounting bolts and realign the brackets.

Do I need to disconnect the battery before I start?

It's a good idea to disconnect the negative battery terminal before you start drilling or running wires. This prevents accidental shorts if you accidentally touch a live wire with a metal tool. Reconnect it only after all wiring is complete and tested.

Will the PowerStep work if I have a tonneau cover or bed cover?

Yes, the PowerStep is independent of the bed cover. The board extends from the rocker panel, not the bed, so a cover won't interfere with it.

How often does the PowerStep motor need maintenance?

The motor is sealed and doesn't require routine maintenance. If it starts moving slowly or stalling, the problem is usually a loose power connection or a blown fuse, not the motor itself. If you live in a very wet climate, check the wiring connections under the truck occasionally to make sure they're not corroded.