Remote start is available as an aftermarket system you install yourself or have a shop install, or as a factory option on newer vehicles
Remote start lets you start your engine from outside the car using a key fob or smartphone app. You have three paths: buy a standalone aftermarket system and have a technician wire it in, purchase a system and install it yourself if you have basic electrical knowledge, or buy a vehicle that came with remote start from the factory. The cost, complexity, and reliability differ significantly between these routes.
Aftermarket systems range from $150 to $500 for the hardware alone, plus $300 to $1,500 in labor if you use a shop. DIY installation saves labor but requires you to run wires through your steering column and dashboard, splice into your car's electrical system, and program the system to your vehicle. Factory remote start costs nothing extra if you buy a car that has it, but adds to the purchase price if you order it as an option on a new vehicle.
Key Takeaways
- Aftermarket remote start systems cost $150 to $500 in parts, plus $300 to $1,500 in labor at a shop, or free if you install it yourself.
- Installation requires running wires from the starter, ignition, and battery through your dashboard and steering column, then programming the system to your car's make and model.
- Aftermarket systems work on most cars built after 1990, but some vehicles with advanced security systems or push-button start may not be compatible.
- Factory remote start is more reliable and integrates with your car's existing systems, but you can only get it by buying a vehicle that offers it as an option.
- Remote start will not work if your car is in gear, the parking brake is not set, or the doors are locked — safety interlocks prevent accidental movement.
How aftermarket remote start systems work
An aftermarket remote start system is a separate device that mimics the action of turning your key in the ignition. The system includes a receiver module that sits under your dashboard, a relay that controls power to the starter, and a transmitter (your key fob or app). When you press the button, the transmitter sends a signal to the receiver, which triggers the relay to engage the starter motor and turn on the ignition.
The system must be wired into four main circuits: the starter wire (so it can crank the engine), the ignition wire (to turn on electrical systems), the battery (for power), and the parking brake wire (a safety interlock that prevents the car from starting if the brake is not set). Some systems also wire into your door locks, so the car locks when you remote-start it, and into your car's security system, so the alarm does not trigger when the engine starts.
What you need to know before buying a system
Check whether your car is compatible with the system you are considering. Most aftermarket remote start systems work on vehicles from 1990 onward, but cars with push-button start, keyless ignition, or advanced security systems often cannot use standard aftermarket systems. Some newer vehicles require a system designed specifically for that make and model, which costs more and may have limited options.
Automatic transmissions are easier to work with than manual transmissions. Remote start on a manual car requires an additional module that confirms the clutch pedal is fully engaged before the engine starts, which adds $100 to $200 to the cost. Some shops will not install remote start on manual vehicles because the safety risk is higher if the system fails.
Your climate and driving habits matter. Remote start is most useful in cold climates where you want to warm up the car before driving, or in hot climates where you want to run the air conditioning before you get in. If you live somewhere with mild weather year-round, the benefit is smaller. Also consider whether your car is parked in a garage or on the street — remote start works through walls and windows, but the range is typically 1,000 to 1,500 feet in open air, and much shorter if there are obstacles.
DIY installation versus professional installation
DIY installation saves $300 to $1,500 in labor but requires you to remove trim panels from your steering column and dashboard, locate the correct wires in your car's wiring harness, and splice them into the remote start module. You will need a wiring diagram specific to your car's year, make, and model — most system manufacturers provide this, but some do not. You will also need basic tools: a wire stripper, crimpers, electrical tape, and a multimeter to test connections.
The hardest part is usually finding the right wires. Your car's wiring harness may have 20 or more wires of similar colors, and connecting to the wrong one can damage your car's electrical system or prevent the remote start from working. Many DIY installers spend 4 to 8 hours on the job, and some have to redo sections when they realize they spliced into the wrong wire.
Professional installation at a car audio shop, alarm shop, or dealership takes 2 to 4 hours and includes testing and programming. The shop has the wiring diagrams for your specific vehicle and can diagnose problems if something goes wrong. If the system fails after installation, the shop is responsible for fixing it. If you install it yourself and something breaks, you own the problem.
Installation steps and what happens during the process
A professional installation follows this order: First, the technician removes trim panels from your steering column and dashboard to access the wiring harness. Second, they locate the starter wire, ignition wire, battery wire, and parking brake wire using a wiring diagram and a multimeter. Third, they run the remote start module's wires through the dashboard and find them with clips and conduit. Fourth, they splice the module's wires into your car's wires using butt connectors or solder joints, then wrap the connections in electrical tape or heat shrink tubing.
Fifth, they program the system to your car's specifications — this usually means entering your car's year, make, and model into the system's control panel, or connecting a laptop to the module to upload the correct firmware. Sixth, they test the system by remote-starting the car multiple times and confirming that the engine starts, idles, and shuts off correctly. Finally, they reinstall all trim panels and test the system again from outside the car.
The entire process takes 2 to 4 hours at a shop. If your car has a complex security system or an unusual wiring layout, it may take longer. Some shops charge a flat rate ($300 to $1,500 depending on your car's complexity), while others charge hourly labor ($75 to $150 per hour) plus the cost of the system.
Smartphone app remote start versus key fob remote start
Aftermarket systems come in two types: traditional key fob systems and smartphone app systems. A key fob system uses a dedicated transmitter that looks like a car key and has a range of 1,000 to 1,500 feet. A smartphone app system uses your phone's cellular connection, so it works from anywhere — you can start your car from inside your house, from work, or from across the country.
Smartphone app systems cost $100 to $300 more than key fob systems and require a cellular module installed in your car, which adds $200 to $400 in labor. The cellular module sends a signal to the remote start system over a cellular network, so you need a data plan or a plan included with the system. Some systems charge a monthly subscription ($5 to $15 per month) to keep the cellular connection active.
Key fob systems are simpler, cheaper, and do not require a subscription, but you have to be within range of your car to use them. Many people buy a key fob system first and upgrade to a smartphone system later if they decide they want the extra range.
Safety features and limitations you should understand
All remote start systems include safety interlocks that prevent the car from moving when you remote-start it. The parking brake must be set, the car must be in Park (for automatics) or Neutral (for manuals), and the doors must be locked. If any of these conditions are not met, the system will not start the engine. These interlocks exist because a remote-started car that is in gear or with the parking brake off could roll forward or backward unexpectedly.
Remote start will shut off the engine automatically after 10 to 20 minutes if you do not get in the car and press the brake pedal. This prevents the engine from running unattended for hours, which wastes fuel and can overheat the engine. Some systems let you extend the runtime by pressing the remote start button again.
Remote start does not work if your car's battery is dead, if the fuel tank is empty, or if the engine is already running. It also does not work if your car's security system is armed — you have to disarm the alarm before the system will start the engine. Some older cars with aftermarket alarms may have compatibility issues where the alarm and remote start interfere with each other.
Frequently Asked Questions
Can I add remote start to a car with push-button start?
Most standard aftermarket remote start systems do not work with push-button start vehicles because the ignition system is different. Some manufacturers make systems designed specifically for push-button cars, but they are more expensive and may not be available for all makes and models. Check with the system manufacturer or a local shop to see if your specific car is supported.
Will remote start void my car's warranty?
It depends on your car's warranty terms and where the system is installed. Factory-installed remote start never voids the warranty. Aftermarket systems installed by a dealership usually do not void the warranty, but aftermarket systems installed by a third-party shop may. Read your warranty document or call your dealership to ask before you have a system installed.
How much does it cost to add remote start to a new car when I buy it?
Factory remote start costs vary by manufacturer and model. On some vehicles it is a $300 to $500 option, while on others it costs $800 to $1,200. You can only order it when you buy the car or during the factory order period — you cannot add it later. Check your car's window sticker or build-and-price tool on the manufacturer's website to see the cost for your specific model.
What is the difference between a one-way and two-way remote start system?
A one-way system sends a signal to your car to start it, but does not send a signal back to confirm that the engine started. A two-way system includes a small display on your key fob that shows whether the engine started successfully. Two-way systems cost $50 to $150 more than one-way systems and are useful if you want confirmation that the car started before you walk out to it.
Can I install remote start myself if I have never done car electrical work before?
It is possible but risky. You will need a wiring diagram, a multimeter, and several hours of time. If you splice into the wrong wire, you could damage your car's electrical system or create a fire hazard. Most people without electrical experience should have a professional install the system to avoid costly mistakes.