What a 50 to 1 gas-oil mix means and why your engine needs it
A 50 to 1 ratio means you add one part oil to fifty parts gasoline. For small engines—chainsaws, leaf blowers, weed trimmers, outboard motors—this mixture lubricates the engine because these machines have no separate oil reservoir. The oil circulates through the engine with the fuel, coating the pistons, cylinders, and bearings as it burns. Without it, the engine seizes within minutes.
Two-stroke engines (the kind that use this ratio) fire once per crankshaft rotation instead of twice, so they need constant lubrication from the fuel itself. Four-stroke engines in cars and trucks have a separate oil pan and oil pump, so you never mix oil into the gas. Mixing oil into regular car fuel will damage the engine.
The ratio matters because too little oil leaves metal parts unprotected and causes scoring and seizure. Too much oil fouls the spark plug, clogs the air filter, and leaves carbon buildup that reduces power. 50 to 1 is the standard ratio for most small engines, though some newer models specify 40 to 1 or even 32 to 1—always check your owner's manual first.
Key Takeaways
- A 50 to 1 ratio means one ounce of oil per 6.4 ounces of gasoline, or one liter of oil per 50 liters of gasoline.
- Use only two-stroke engine oil (also called two-cycle oil), never car oil or synthetic motor oil not rated for two-stroke use.
- Mix the oil and gas in a separate container before pouring into the fuel tank—never mix directly in the tank.
- Your owner's manual may specify a different ratio; always follow the manufacturer's recommendation over the standard 50 to 1.
- Pre-mixed fuel is available at most hardware and outdoor equipment stores if you do not want to measure and mix yourself.
How to calculate the exact amount for your fuel tank
Start by knowing your fuel tank size. A typical chainsaw holds 20 ounces (about 600 milliliters), a leaf blower holds 16 to 32 ounces, and an outboard motor holds several gallons. Check your manual or look for a fill line inside the tank.
For a 50 to 1 ratio, divide the tank size by 50 to get the amount of oil needed. A 20-ounce tank needs 20 ÷ 50 = 0.4 ounces of oil. A 1-gallon (128-ounce) tank needs 128 ÷ 50 = 2.56 ounces of oil. A 5-gallon tank needs 5 ÷ 50 = 0.1 gallons, or 12.8 ounces of oil.
Use a measuring cup or syringe marked in ounces or milliliters. Eyeballing the amount will throw off the ratio and damage the engine. If your tank size is not listed in your manual, fill it completely and note how much fuel you poured in—that is your tank capacity.
| Tank Size | Oil Needed (50:1) |
|---|---|
| 16 ounces | 0.32 ounces |
| 20 ounces | 0.4 ounces |
| 32 ounces | 0.64 ounces |
| 1 gallon (128 oz) | 2.56 ounces |
| 5 gallons | 12.8 ounces |
| 10 gallons | 25.6 ounces |
The right way to mix gas and oil without mistakes
Never mix oil and gas directly in the fuel tank. Measure both into a separate, clean container first—a plastic gas can, a measuring pitcher, or a dedicated mixing bottle. Pour the gasoline in first, then add the oil. Stir or shake the container for 30 seconds to blend them evenly. The mixture should look uniform and slightly cloudy, not separated.
Always use fresh gasoline, not fuel that has been sitting for months. Old gas breaks down and will not mix properly with the oil. If you are storing mixed fuel for later use, keep it in a sealed container away from direct sunlight and use it within 30 days. Longer storage causes the oil and gas to separate and the fuel to gum up.
Pour the mixed fuel into your engine's tank slowly and carefully. Wipe up any spills when ready—mixed fuel is flammable and toxic. Never smoke or use an open flame near the mixing area. Wash your hands after handling the mixture.
Choosing the correct two-stroke oil for your engine
Two-stroke oil is not the same as car motor oil. Car oil is too thick and will not burn cleanly in a two-stroke engine. Look for a bottle labeled two-stroke engine oil, two-cycle oil, or 2T oil. Most hardware stores, outdoor equipment dealers, and auto parts stores stock it near the fuel section.
Two-stroke oils come in mineral (conventional) and synthetic varieties. Mineral oil is cheaper and works fine for occasional use. Synthetic oil burns cleaner, leaves less carbon buildup, and is better for engines that run hard or in hot weather. Both types work at 50 to 1 unless your manual says otherwise. Some engines specify synthetic only—check before you buy.
Avoid using automotive motor oil, marine engine oil not rated for two-stroke use, or oil meant for four-stroke engines. These will not burn properly and will foul your spark plug and damage the engine. The bottle must say "two-stroke" or "two-cycle" clearly on the label.
What happens if you get the ratio wrong
Too little oil (a ratio leaner than 50 to 1) starves the engine of lubrication. The piston and cylinder walls rub metal-to-metal without a protective film. Within a few minutes to a few hours of running, the piston seizes, the engine stops, and the damage is permanent. Rebuilding or replacing the engine costs hundreds of dollars.
Too much oil (a ratio richer than 50 to 1) fouls the spark plug with carbon and oil residue, causing the engine to misfire or not start at all. It also clogs the air filter faster and leaves sticky buildup inside the combustion chamber that reduces power and fuel economy. The engine will not seize when ready, but performance drops noticeably and long-term damage accumulates.
The safest approach is to measure carefully and follow your manual. If you are unsure about the ratio, buy pre-mixed fuel instead—it costs a bit more but removes the guesswork and protects your engine.
Pre-mixed fuel as an alternative to measuring yourself
Most outdoor equipment retailers sell pre-mixed two-stroke fuel in cans, already blended at 50 to 1 or the ratio your engine needs. Brands like TruFuel and Caltex Pre-Mix are common. You straightforward pour it into the tank—no measuring, no mixing, no risk of getting the ratio wrong. The trade-off is cost: pre-mixed fuel runs two to three times the price of buying gas and oil separately.
Pre-mixed fuel also has a longer shelf life than fuel you mix yourself, usually 2 to 3 years unopened. Once opened, use it within 30 days. If you use your equipment only a few times a year or store it for winter, pre-mixed fuel is worth the extra money because it will not separate or gum up the way homemade mixes can.
Check the label to confirm the ratio matches your engine. Some equipment specifies 40 to 1 or 32 to 1, and using the wrong pre-mixed ratio will cause the same problems as measuring incorrectly.
Frequently Asked Questions
Can I use car motor oil or synthetic motor oil in my chainsaw?
No. Car motor oil is too thick and will not burn cleanly in a two-stroke engine. Use only oil labeled two-stroke, two-cycle, or 2T. Synthetic motor oil designed for cars will damage the engine the same way.
What if I accidentally mixed the wrong ratio?
Drain the tank completely and refill with correctly mixed fuel. If the engine has already run on the wrong mix, let it cool, then drain and refill. If the engine seized or will not start after running on too-lean a mix, the internal damage is likely permanent and the engine may need rebuilding.
How long can I store mixed gas and oil?
Use mixed fuel within 30 days. Store it in a sealed container away from sunlight. After 30 days, the oil and gas begin to separate and the fuel breaks down, causing starting problems and poor performance.
Do I need to drain old fuel before mixing new fuel?
Yes. Always drain the tank completely before adding new mixed fuel. Old fuel left in the tank will mix with the new fuel and throw off the ratio, plus old fuel gums up and clogs the carburetor.
What if my manual says a different ratio than 50 to 1?
Follow your manual. Newer engines often specify 40 to 1 or 32 to 1 because they have tighter tolerances and better fuel injection. Using 50 to 1 on an engine that needs 40 to 1 will run too lean and cause damage.