What .22 Creedmoor load data tells you and where to find it
.22 Creedmoor load data is a set of tested powder charges, bullet weights, and primer types that tell you how to safely reload ammunition in this cartridge. The data comes from powder manufacturers, bullet makers, and independent testing labs — not from a single source. Different sources sometimes list different maximum loads for the same bullet and powder combination, so you need to know which publishers are most reliable and how to read their tables correctly.
The most widely used sources are Hodgdon Reloading Data (owned by the ammunition company), Alliant Powder's published data, Sierra Reloading Manual (print and online), and Nosler Reloading Guide. Each tests their own powders and bullets under controlled conditions. Some reloaders also reference data from Powder Valley, Midway USA's reloading section, and specialty forums where shooters document their own loads — though forum data is not tested by manufacturers and carries more risk.
Load data for .22 Creedmoor is less abundant than data for older cartridges like .308 Winchester or .223 Remington, because .22 Creedmoor is newer (introduced around 2017). You may find fewer powder options listed, and some powder manufacturers have not published .22 Creedmoor data at all. This means you cannot always use the exact powder you have on hand — you may need to buy a powder that has published data for this cartridge.
Key Takeaways
- Load data comes from powder makers and bullet manufacturers, each testing under their own conditions, so maximum loads vary between sources.
- Start with published data from Hodgdon, Alliant, Sierra, or Nosler rather than forum posts or older manuals, because .22 Creedmoor is too new for most legacy sources.
- Always use the starting load listed in your source, then increase in small steps (usually 0.3 to 0.5 grains) while watching for pressure signs like flattened primers or hard extraction.
- Different bullet weights (55 to 90 grains are common in .22 Creedmoor) require separate load data — you cannot use the same charge weight for a 55-grain bullet as you would for an 80-grain bullet.
- If you cannot find data for your exact powder and bullet combination, do not guess or interpolate; buy a powder that has published data or use a different bullet weight.
How to read a load data table and what each column means
A typical load data table lists the bullet weight and type first, then the powder name, then a starting load (in grains), a maximum load, the primer type, and the case. Some tables also show velocity and pressure in PSI or SAAMI units. The starting load is the lowest safe charge; the maximum load is the highest the manufacturer tested without pressure problems in their equipment.
The gap between starting and maximum load is your working range. You begin at the starting load, fire a few rounds, and inspect the brass for pressure signs. If the primers look normal (not flattened or cratered), the cases extract smoothly, and the bolt closes easily, you can increase the charge by 0.3 to 0.5 grains and test again. You stop when you reach the maximum load listed or when you see pressure signs, whichever comes first.
Primer type matters because different primers have different hardness and cup thickness. A load data table that specifies "CCI 450" (a standard small rifle primer) may produce higher pressure with a softer primer like a Federal 205. Always use the primer type listed in the data, or consult the powder maker before substituting. Case brand also affects pressure slightly — Lapua brass is thicker than some other brands — so if you use a different case than the one listed, start lower and work up more carefully.
Pressure signs to watch for when working up a load
Pressure signs are physical changes to the brass and bolt that tell you the load is too hot. The most reliable sign is a flattened or cratered primer — the primer cup loses its dome shape and the firing pin leaves a deep impression. This means pressure is high enough to deform the primer metal. Stop when ready and drop back to the previous load.
Hard extraction is the second sign: the bolt requires noticeably more force to open, or you have to tap the handle with your hand. This happens because high pressure expands the brass so much that it grips the chamber walls. Sticky extraction often appears before flattened primers, so it is a useful early warning. Flattened or cratered primers are the more definitive sign, but if extraction feels wrong, stop and drop back.
Separated cases — where the case wall splits near the head — mean pressure was dangerously high and you have already passed the safe zone. This is rare if you follow load data, but it is a reason to start low and increase gradually rather than jumping to the maximum load. Discolored or split primer pockets also indicate pressure problems. If you see any of these, stop shooting that load, reduce the charge by at least 1 grain, and start over.
Why .22 Creedmoor load data differs between sources
Different manufacturers test in different equipment. Hodgdon tests in a Pressure Trace system; Sierra uses their own test barrels; Nosler uses yet another setup. A barrel's chamber dimensions, bore diameter, and throat length all affect pressure. A load that produces 62,000 PSI in one test barrel might produce 64,000 PSI in another, even with identical powder, bullet, and primer. This is why maximum loads vary by 1 to 3 grains between reputable sources.
Powder lot variation also plays a role. A powder lot made in 2020 may burn slightly faster or slower than a lot made in 2024, even from the same manufacturer. Published data is based on a specific lot, and the powder maker tests new lots to make sure they stay within the same burn rate window. But small shifts happen, which is another reason to start at the published starting load rather than jumping to the maximum.
Bullet construction matters too. A 75-grain bullet from one maker may have a different jacket thickness or core hardness than a 75-grain bullet from another maker, affecting how it handles pressure. Load data is specific to the bullet tested — using a different brand of the same weight can shift pressure. Always match the bullet brand and weight to the data you are using.
Common powders for .22 Creedmoor and where to find their data
Hodgdon H4895 and Varget are among the most common powders listed for .22 Creedmoor, and Hodgdon publishes extensive data on their website (hodgdon.com). Alliant Reloder 15 and Reloder 17 also have published .22 Creedmoor data. IMR Powders (now owned by Hodgdon) lists IMR-4166 and IMR-4895 for this cartridge. Winchester 748 has some published loads, though less widely than Hodgdon or Alliant products.
Slower powders like H4350 or Varget work better in .22 Creedmoor than fast powders like 2208 or 4227, because the cartridge has a longer case and benefits from slower burn rates. If you own a powder that does not have published .22 Creedmoor data, do not assume you can use data from a similar cartridge like .223 Remington — the case capacity and pressure rating are different enough that the charge weight would be unsafe.
Reloading supply websites like Midway USA, Powder Valley, and Brownells stock load data sheets from manufacturers, often free to read as PDFs. Hodgdon and Alliant also offer free online databases where you can search by cartridge and powder name. Print manuals like the Sierra Reloading Manual and Nosler Reloading Guide are available new or used and cover .22 Creedmoor in recent editions.
How bullet weight changes the load data you need
.22 Creedmoor is typically loaded with bullets ranging from 55 grains (varmint hunting) to 90 grains (long-range target shooting). Each weight class requires its own load data because the bullet's mass and bearing surface affect how the powder burns and how pressure builds. A 55-grain load will use less powder than a 90-grain load, sometimes by 3 to 5 grains depending on the powder.
Lighter bullets accelerate faster and reach peak pressure sooner, so they need less powder to stay safe. Heavier bullets take longer to accelerate, so they can handle more powder before pressure becomes excessive. This is why you cannot straightforward use a 55-grain load with an 80-grain bullet — the pressure would be too high. Always look up the specific bullet weight in your load data table, or find a new source if your weight is not listed.
If you shoot multiple bullet weights, keep separate load notes for each one. Write down the powder, charge weight, primer, bullet weight and brand, case brand, and the velocity or pressure reading if you have a chronograph. This prevents mixing up loads and helps you spot patterns if one weight shoots better than another in your rifle.
When you cannot find data for your exact combination
If your powder and bullet combination does not appear in any published source, your options are limited. The safest choice is to buy a powder that has published data for your bullet weight, or buy a different bullet weight that has data for your powder. Trying to interpolate between two different loads or using data from a similar cartridge introduces risk that the load will be unsafe.
Some reloaders consult online forums or ask experienced shooters for guidance, but forum loads are not tested by manufacturers and carry more uncertainty. If you do research a forum load, treat it as a starting point only — begin well below the suggested charge, watch carefully for pressure signs, and increase very slowly. Never assume a forum load is safe just because someone says it worked in their rifle.
Another option is to contact the powder maker directly. Hodgdon, Alliant, and other manufacturers sometimes have unpublished data or can advise whether a load for a similar cartridge is close enough to adapt. They may ask for your rifle's specifications (barrel length, chamber type) to give you a more informed answer. This takes time but is more reliable than guessing.
Frequently Asked Questions
Can I use .223 Remington load data for .22 Creedmoor?
.22 Creedmoor has a larger case capacity than .223 Remington, so .223 loads will produce dangerously high pressure in .22 Creedmoor. The cartridges are not interchangeable. Always use load data published specifically for .22 Creedmoor.
What if I only have an old reloading manual that does not list .22 Creedmoor?
.22 Creedmoor was introduced around 2017, so manuals printed before 2018 will not have data for it. read free data from Hodgdon or Alliant online, or buy a recent edition of Sierra or Nosler manuals. Do not try to adapt data from older cartridges.
Is it safe to use the maximum load listed in the data right away?
No. Always start at the published starting load, fire a few rounds, and inspect the brass for pressure signs. Increase in small steps (0.3 to 0.5 grains) until you reach the maximum load or see pressure signs. Starting at maximum risks a dangerous overpressure condition.
Do I need a chronograph to reload .22 Creedmoor safely?
A chronograph is helpful but not required. You can watch for pressure signs (flattened primers, hard extraction) without one. A chronograph tells you velocity, which helps you spot when a load is producing unusual results, but it does not replace visual pressure inspection.
What happens if I use a different primer brand than the data specifies?
Different primer brands have different hardness and cup thickness, which can shift pressure by 500 to 1,500 PSI. If you must substitute, start lower than the published starting load and work up carefully while watching for pressure signs. Ideally, use the primer type listed in the data.