How long the 2019 Ram 1500 Classic 3.6L oil filter housing job takes
The oil filter housing replacement on a 2019 Ram 1500 Classic with the 3.6L engine typically takes 1.5 to 2.5 hours at a shop, depending on whether the technician needs to remove other components to reach it. The housing sits on top of the engine, but access can be tight depending on what's mounted nearby. If you're doing this yourself with basic tools and no complications, plan for 2 to 3 hours your first time.
Book time — the flat-rate hours a shop charges — usually runs 1.5 to 2 hours for this job. That's what you'll see quoted when you call a dealership or independent shop. The actual time spent can be shorter or longer depending on whether the filter housing is stuck, whether coolant lines need to be moved, and whether the technician has done this repair before on this engine.
The job involves draining the old filter housing, unbolting it from the engine block, replacing the internal filter element and seals, and reinstalling with new gaskets. It's not a straightforward spin-off filter change — the housing itself comes apart.
Key Takeaways
- Book time for a 2019 Ram 1500 Classic 3.6L oil filter housing replacement is typically 1.5 to 2 hours at a shop.
- The housing sits on top of the engine but may require moving coolant hoses or other components to access fully.
- DIY work takes 2 to 3 hours if you have basic hand tools and a torque wrench, longer if the housing is seized.
- You'll need a new filter element, housing gasket, and O-rings; the old gasket cannot be reused.
- Dealerships typically charge more for labor than independent shops, though parts pricing is often similar.
What you need before you start
Gather a socket set, wrenches, a drain pan, a torque wrench, and a gasket scraper before you begin. The oil filter housing bolts are typically 10mm or 13mm, but confirm with your service manual or a parts diagram. You'll also need the replacement gasket kit specific to the 3.6L — do not reuse the old gasket, as it will not seal properly.
Have a new oil filter element on hand as well. The 2019 Ram 1500 Classic 3.6L uses a cartridge-style filter that sits inside the housing, not a traditional spin-on filter. If you're at a shop, they'll have these in stock, but if you're doing this yourself, order the correct part number ahead of time to avoid delays.
You'll also need fresh oil to top off after the job. The housing holds a small amount of oil, so you may lose a quart or so during the replacement. Check your owner's manual for the correct viscosity and capacity.
Step-by-step process for the housing replacement
Start by letting the engine cool for at least 30 minutes after running, then disconnect the negative battery terminal. Locate the oil filter housing on top of the engine — it's a cylindrical component with a large center bolt. Place your drain pan underneath and loosen the center bolt by hand first, then use a socket wrench to remove it completely.
Once the center bolt is out, the old filter element will come free. Drain any remaining oil into your pan. Next, unbolt the housing itself from the engine block — there are typically three or four bolts around the perimeter. Keep track of bolt locations, as they may be different lengths. Remove the old gasket and O-rings from the housing and the engine block, scraping away any residue with a gasket scraper.
Clean the sealing surfaces on both the housing and the engine block with a lint-free cloth. Install the new gasket and O-rings on the housing, then position the housing back on the engine block. Hand-tighten the bolts first, then torque them to the specification in your service manual — typically 18 to 22 foot-pounds for the 3.6L. Install the new filter element, then reinstall and torque the center bolt, usually to 25 to 30 foot-pounds.
Reconnect the battery, start the engine, and check for leaks around the housing and center bolt. Let it run for a minute, then shut it off and wait five minutes before checking the oil level. Top off if needed, then run the engine again and recheck for leaks before considering the job complete.
When to replace the oil filter housing versus just the filter
Most of the time, you're only replacing the filter element and gaskets inside the housing, not the housing itself. The housing is metal and rarely fails unless it's cracked or the threads are stripped. If you notice oil leaking from the seams of the housing itself rather than from the center bolt or gasket, the housing may need replacement.
If the center bolt threads are stripped and won't hold torque, or if the housing is visibly cracked, you'll need a new housing assembly. This adds significantly to the job time and cost, as the new housing must be installed and filled with fresh oil. A stripped center bolt can sometimes be repaired with a threaded insert kit, which takes an additional 30 minutes to an hour.
Shop labor costs versus DIY time investment
At a dealership, expect to pay 1.5 to 2 hours of labor at the shop's hourly rate, which typically ranges from $100 to $150 per hour depending on your location and the dealership. That's $150 to $300 in labor alone, plus parts. Independent shops often charge $80 to $120 per hour, bringing labor to $120 to $240 for the same job.
If you do the work yourself, your main cost is the gasket kit and filter element — usually $30 to $60 combined. You'll save the labor cost but invest 2 to 3 hours of your time. The job is straightforward enough for someone with basic mechanical experience, but it requires patience and attention to torque specifications to avoid leaks.
Common problems that extend the job time
The center bolt can seize if the housing hasn't been serviced in a long time. If it won't budge with a socket wrench, explore penetrating oil and wait 15 to 20 minutes before trying again. Forcing a seized bolt risks stripping the threads or breaking the bolt itself, which turns a 2-hour job into a 4-hour repair.
Coolant hoses or other engine components may be in the way, requiring temporary removal to access the housing fully. This adds 20 to 30 minutes to the job. If the gasket is stuck to the engine block, scraping it off carefully without gouging the sealing surface takes extra time. Some technicians use a gasket removal tool or heat gun to soften old gasket material, which adds another 15 to 20 minutes.
Tools and parts checklist
| Item | Purpose | Notes |
|---|---|---|
| Socket set (10mm, 13mm) | Remove housing bolts and center bolt | Confirm sizes with your manual |
| Torque wrench | Tighten bolts to specification | Essential to prevent leaks |
| Drain pan | Catch spilled oil | At least 2-quart capacity |
| Gasket scraper | Remove old gasket material | Plastic scraper prevents surface damage |
| Oil filter housing gasket kit | New seals for the housing | Do not reuse old gasket |
| Oil filter element | Replace cartridge filter inside housing | Specific to 3.6L engine |
| Fresh engine oil | Top off after replacement | Check manual for viscosity |
| Lint-free cloth | Clean sealing surfaces | Prevents debris in oil passages |
Frequently Asked Questions
Can I replace just the filter element without removing the housing?
No. The filter element sits inside the housing, so you must unbolt the housing from the engine to access it. You cannot reach the element by removing the center bolt alone — the housing itself must come off. This is why the job takes longer than a traditional spin-on filter change.
What happens if I don't replace the gasket?
The old gasket will leak oil. Gaskets compress over time and lose their seal, especially after being heated and cooled repeatedly. Reusing the old gasket almost always results in seepage around the housing perimeter or center bolt within days or weeks of the repair.
Do I need to drain the entire oil pan before replacing the housing?
No. You only need to drain enough oil to prevent spillage when the housing comes off — typically a quart or less. The housing itself holds a small amount of oil, not the entire engine supply. Drain your pan, remove the housing, then top off the engine oil after reinstalling.
Why does the book time vary so much between shops?
Book time depends on the shop's flat-rate manual and the technician's experience with this specific engine. Some shops may quote 1.5 hours if they've done the job many times; others quote 2.5 hours if they anticipate complications or if their manual is more conservative. Always ask what's included in the quoted time.
Is this job worth doing at a dealership versus an independent shop?
Independent shops typically charge less per hour and may complete the job faster if they're familiar with the 3.6L. Dealerships have access to OEM parts and may have more experience with Ram-specific issues, but you'll pay a premium for labor. For a straightforward housing replacement with no complications, an independent shop is usually the better value.