The Cim-tek 70003 is a replacement fuel filter cartridge designed for the Cim250e10 fuel polishing system, rated to remove particles 10 microns and larger from diesel or gasoline tanks.
The Cim250e10 is a portable fuel conditioning unit—a tank-mounted or standalone system that circulates fuel through a filter to remove water, sediment, and particulate matter. The 70003 cartridge is the filter element inside that system. A 10-micron rating means it stops particles smaller than a human hair but larger than bacteria. This matters because fuel tanks accumulate rust, dirt, and oxidized fuel byproducts over time, especially in equipment that sits idle or in older vehicles and machinery.
If your fuel system has a Cim250e10 unit already installed or you own one, you will eventually need to replace the 70003 cartridge. How often depends on how dirty your fuel is and how much you run the polisher. A tank with heavy contamination might need a new cartridge after 50 to 100 hours of circulation; a cleaner tank might go 200 hours or more.
Key Takeaways
- The Cim-tek 70003 is a replacement cartridge for the Cim250e10 fuel polishing system, not a standalone filter.
- A 10-micron rating removes visible sediment, rust particles, and water but does not remove dissolved fuel degradation or very fine silt.
- You need a new cartridge when flow slows noticeably or when you have finished polishing a heavily contaminated tank.
- The cartridge screws into the Cim250e10 housing and takes less than five minutes to change.
- Cim-tek also makes finer (3-micron) and coarser (25-micron) cartridges for different fuel conditions and flow requirements.
What a 10-Micron Rating Actually Stops
Micron size is a measure of particle diameter. One micron is one-millionth of a meter. A 10-micron filter will stop particles 10 microns and larger; smaller particles pass through. For context, a human hair is roughly 75 microns wide, a grain of sand is 100 to 200 microns, and rust particles from a corroded tank wall range from 5 to 50 microns depending on how long they have been oxidizing.
At 10 microns, the Cim-tek 70003 catches most visible contamination—the sediment you can see if you hold a fuel sample up to light, the rust flakes that settle at the bottom of a tank, and the sludge that forms when fuel oxidizes. It also removes water droplets that have coalesced into particles large enough to settle. What it does not remove are dissolved contaminants (fuel that has chemically broken down), very fine clay or silt particles (which are smaller than 10 microns), or bacteria and microorganisms (which are measured in fractions of a micron).
If your fuel has a serious water problem—free water pooling at the tank bottom—you need a water-absorbing cartridge or a separate water-removal system, not just a particulate filter. The Cim250e10 system can be fitted with different cartridge types, so check your unit's documentation or contact Cim-tek to confirm which cartridge suits your contamination type.
When to Replace the 70003 Cartridge
The cartridge does not have a fixed lifespan. It wears out based on how much fuel passes through it and how dirty that fuel is. You will notice two signs that replacement is due: the flow rate from the Cim250e10 drops noticeably (the pump works harder and fuel moves slower), or the pressure gauge on the unit (if equipped) climbs into the red zone.
If you are polishing a tank that has been sitting for years or contains visible sludge, expect to change the cartridge more often. A tank with light dust and no water might let one cartridge last through the entire polishing cycle. A tank with heavy rust and sediment might clog a cartridge halfway through, forcing you to swap it out and continue.
Some operators change the cartridge as preventive maintenance after every major polishing job, even if flow is still acceptable. This is reasonable if you work on many different tanks and want to avoid cross-contamination—old fuel residue in a clogged cartridge can leach back into clean fuel if the system sits idle. If you run the same Cim250e10 on your own equipment, you can stretch cartridge life by stopping the polisher as soon as flow drops and replacing the cartridge then.
How to Install a New 70003 Cartridge
The Cim250e10 housing has a cartridge bowl—a cylindrical chamber that screws onto the main body. To change the cartridge, shut off the pump, relieve any pressure in the system (if your unit has a bleed valve, open it), and unscrew the bowl counterclockwise by hand or with a filter wrench if it is tight. The old cartridge will come out with the bowl.
Inspect the bowl's internal sealing surface for debris or damage. Wipe it clean with a lint-free cloth. Screw the new 70003 cartridge into the bowl by hand until the rubber seal on top of the cartridge contacts the bowl's underside, then turn it another three-quarter turn to compress the seal. Do not over-tighten; hand-tight plus three-quarter turn is correct. Screw the bowl back onto the housing until snug, then run the pump for a few seconds to bleed air from the system.
The entire job takes five minutes. If fuel leaks from the bowl seam after you reassemble it, the seal may not be seated correctly—unscrew the bowl, check that the cartridge seal is clean and not pinched, and reinstall it.
Cim-tek Cartridge Options and When to Use Them
Cim-tek makes three particulate cartridges for the Cim250e10: the 70003 (10-micron), the 70001 (3-micron), and the 70005 (25-micron). The choice depends on your fuel condition and how fast you need the polisher to work.
The 25-micron cartridge (70005) moves fuel faster but stops only large particles. Use it for a first pass on heavily contaminated fuel or when you need high flow rate and do not mind leaving fine sediment behind. The 10-micron cartridge (70003) is the middle ground—it removes most visible contamination and maintains reasonable flow. The 3-micron cartridge (70001) catches very fine particles and is used for a final polish or for fuel that is already fairly clean. A 3-micron cartridge will clog faster on dirty fuel, so do not start with it on a tank full of sludge.
Some operators use a two-stage approach: run the 25-micron cartridge first to move volume quickly and remove bulk contamination, then swap to the 10-micron or 3-micron cartridge for a finer finish. This saves time and cartridge cost compared to running a fine cartridge through heavily dirty fuel from the start.
Storage and Shelf Life
The Cim-tek 70003 cartridge is a dry filter element made of pleated synthetic media. It has no expiration date if stored in a clean, dry place. Keep it in its original packaging or a sealed bag to prevent dust from settling on the media. If you store a cartridge for months or years and then install it, inspect it visually for dust or damage before use. A cartridge that has been exposed to moisture or extreme heat may have degraded media and should be replaced rather than installed.
Once installed and used, the cartridge cannot be cleaned and reused. Attempting to backflush or wash a clogged cartridge will damage the media and may allow unfiltered fuel to bypass the element. Dispose of used cartridges according to your local hazardous waste rules—they contain fuel residue and should not go in regular trash.
Frequently Asked Questions
Can I use the 70003 cartridge in a different fuel polishing system?
No. The 70003 is designed specifically for the Cim250e10 housing. Other Cim-tek systems use different cartridge designs and thread patterns. Using the wrong cartridge can cause leaks or allow unfiltered fuel to bypass the element. Check your system's manual or contact Cim-tek to confirm which cartridge fits your unit.
What happens if I run the polisher with a clogged cartridge?
The pump will work harder, flow will drop to a trickle, and the motor may overheat if the unit runs continuously. Pressure inside the housing rises, which can eventually rupture seals or crack the bowl. Stop the polisher as soon as you notice slow flow and change the cartridge. Running a clogged system does not damage the fuel—it just wastes time and risks damaging the equipment.
Is 10 microns fine enough to clean fuel for fuel injection systems?
A 10-micron filter removes most visible contamination and is suitable for many diesel engines and older gasoline engines. Modern fuel injectors are more sensitive and may require 3-micron or finer filtration. If you are polishing fuel for a high-precision engine, consult the engine manufacturer's fuel cleanliness specification or use a 3-micron cartridge for the final stage of polishing.
How much does a replacement 70003 cartridge cost?
Prices vary by supplier and region. Cim-tek cartridges are sold through fuel polishing equipment distributors, industrial supply shops, and online retailers. Expect to pay between $40 and $80 per cartridge depending on where you buy. Buying in bulk (five or ten cartridges at once) often reduces the per-unit cost.
Can I use a generic fuel filter cartridge instead of the Cim-tek 70003?
No. Generic cartridges are designed for different housings and thread patterns and will not fit the Cim250e10 or will not seal properly. Using the wrong cartridge risks fuel leaks and unfiltered fuel bypassing the element entirely. Always use the Cim-tek 70003 or another cartridge specifically rated for the Cim250e10 system.