LS firing order is the sequence in which the spark plugs ignite the fuel in each cylinder, and it's 1-8-4-3-6-5-7-2 on all LS engines
The firing order is the order in which each cylinder fires — meaning the order in which the spark plugs ignite the air-fuel mixture. On LS engines (the small-block V8 family that includes the LS1, LS2, LS3, and LS7), that sequence is always 1-8-4-3-6-5-7-2. This matters because if your spark plug wires or coil packs are connected in the wrong order, your engine won't run, will run rough, or will damage itself.
The firing order is determined by how the engine's crankshaft and camshaft are timed together. You cannot change it — it's built into the engine's design. What you can control is making sure the ignition components are wired correctly when you install new spark plugs, replace ignition coils, or rebuild the top end of the engine.
Key Takeaways
- LS firing order is 1-8-4-3-6-5-7-2, and this sequence is the same across all LS engine variants.
- Cylinder numbering on LS engines runs 1-2-3-4 on the driver's side and 5-6-7-8 on the passenger's side, front to back.
- Spark plug wires or coil packs must be connected in firing order sequence, or the engine will misfire, run rough, or not start.
- Incorrect firing order is one of the most common causes of no-start and rough idle after ignition work, and it's usually caught by checking the service manual before installation.
How cylinder numbering works on LS engines
LS engines are V8s, meaning eight cylinders arranged in two banks of four. The driver's side bank (also called the left bank) holds cylinders 1, 2, 3, and 4, numbered front to back. The passenger's side bank (right bank) holds cylinders 5, 6, 7, and 8, also front to back. The front of the engine is the end closest to the radiator.
This layout matters because when you're looking at the engine from above or from the side, you need to know which cylinder is which. A common mistake is reversing the banks or numbering them back-to-front. The service manual for your specific vehicle shows a diagram of cylinder location — use it every time you work with ignition components.
Why firing order affects engine performance
The firing order determines the sequence in which combustion happens in each cylinder. That sequence is timed to balance the forces on the crankshaft and keep the engine running smoothly. If spark plugs fire out of order, the crankshaft experiences uneven loads, the engine vibrates, and power delivery becomes erratic.
More importantly, wrong firing order can cause the engine to run so rough that it damages itself. Severe misfires create heat spikes in the cylinders, which can warp the cylinder head, crack the block, or damage the pistons. This is why a no-start or rough idle after ignition work should be treated as a firing order problem until proven otherwise.
Spark plug wire routing on older LS engines
LS1 and LS2 engines (2005 and earlier, or early 2006 models) use individual spark plug wires connected to a distributor-style coil pack mounted on top of the engine. The wires must be routed in firing order: the wire from terminal 1 on the coil pack goes to cylinder 1, terminal 2 to cylinder 8, terminal 3 to cylinder 4, and so on through all eight terminals.
The coil pack itself is labeled with terminal numbers. Trace each terminal carefully and follow the service manual diagram. Wires that cross over each other or are routed in a tangled pattern are often a sign that they're in the wrong order. Take a photo of the correct routing before you remove the old wires, or print the manual diagram and keep it in front of you during installation.
Coil-on-plug systems on newer LS engines
LS3, LS7, and later LS variants use coil-on-plug ignition, where a separate ignition coil sits directly on top of each spark plug. There are no wires to route — each coil is labeled with the cylinder number it serves. This design is more reliable because there's no wire to crack or corrode, but it also means you must install each coil on the correct cylinder.
When you replace a coil-on-plug unit, the new coil must go on the same cylinder as the old one. If you remove all eight coils at once and reinstall them, use the cylinder numbers stamped or printed on the coil body to guide you. If the numbers are worn off, the service manual shows which coil goes where. Installing a coil on the wrong cylinder will cause a misfire on that cylinder and trigger a check engine light.
What to do if your engine misfires after ignition work
If you've recently replaced spark plugs, spark plug wires, or ignition coils and the engine now misfires, runs rough, or won't start, the first step is to verify the firing order. Pull the service manual for your vehicle and compare the diagram to what you've installed. Look for wires in the wrong terminals, coils on the wrong cylinders, or wires routed in a way that doesn't match the manual.
A misfire will also trigger a check engine light and store a diagnostic trouble code. A code like P0301 means cylinder 1 is misfiring, P0302 means cylinder 2, and so on. This code tells you which cylinder to check first. Verify that the spark plug wire or coil for that cylinder is connected to the correct terminal or cylinder, then clear the code and test-drive the vehicle.
Firing order and engine swaps
If you're installing an LS engine into a different vehicle (a common modification), the firing order stays 1-8-4-3-6-5-7-2. However, the cylinder numbering on the LS may not match the cylinder numbering on the original engine in that vehicle. This is where mistakes happen. You must use LS cylinder numbering, not the original engine's numbering.
The engine bay layout also matters. If the LS is installed in a different orientation than the original engine, the driver's side and passenger's side banks may be reversed relative to the vehicle. Check the engine's actual orientation in the bay, identify which bank is which, and number the cylinders accordingly. The service manual for the LS engine is your reference — not the manual for the original vehicle.
Frequently Asked Questions
Can I change the firing order on an LS engine?
No. Firing order is determined by how the crankshaft and camshaft are machined and timed together. It cannot be changed without completely rebuilding the engine with different internal parts. If you need a different firing order, you need a different engine.
What happens if I install spark plug wires one position off?
The engine will misfire severely on multiple cylinders. Each wire will be connected to the wrong cylinder, so combustion will happen at the wrong time in each cylinder. The engine may not start, or it will run so rough that you'll notice when ready. Check and correct the routing before driving.
Do I need to clear the check engine light after fixing the firing order?
Yes. After you correct the firing order and verify the engine runs smoothly, use a diagnostic scanner to clear the stored misfire codes. The light should not return if the firing order is correct. If it does, the problem is not firing order.
Is firing order the same on LS1, LS2, LS3, and LS7 engines?
Yes. All LS variants use the same firing order: 1-8-4-3-6-5-7-2. The difference is in the ignition system type — older models use spark plug wires, newer models use coil-on-plug — but the sequence is identical.
How do I know which end of the engine is the front?
The front of the engine is the end closest to the radiator and the front of the vehicle. The back is the end closest to the firewall. If you're unsure, the service manual includes a diagram showing the engine orientation and cylinder locations. Use that diagram every time.