Spark plugs wear out and need replacement every 30,000 to 100,000 miles depending on the type

Replacing spark plugs is a maintenance task you can do yourself on most vehicles, though the difficulty varies widely. Some cars have plugs you can reach in minutes; others require removing the intake manifold or other engine parts. The job involves removing the old plugs, gapping new ones to your engine's specification, and installing them in the correct firing order. If you're comfortable working under the hood and have basic tools, this is doable. If you're not, a mechanic will charge between $100 and $300 depending on how many plugs your engine has and how hard they are to reach.

The first step is finding out what your vehicle needs: the correct plug type, gap size, and how many plugs your engine has. This information is in your owner's manual or on a sticker under the hood. You'll also need to know whether your car uses standard copper plugs (replaced every 30,000 miles), platinum plugs (50,000 to 100,000 miles), or iridium plugs (100,000+ miles). Buying the wrong type or gap size won't damage anything, but the plugs won't fire correctly and your engine will run rough.

Key Takeaways

  • Your owner's manual or the sticker under your hood tells you the exact plug type, gap size, and firing order your engine needs.
  • You need a spark plug socket (different from a regular socket), a ratchet, a gap tool, and new plugs rated for your vehicle's mileage interval.
  • Remove one plug at a time, gap the new one, and install it in the same cylinder to avoid mixing up the firing order.
  • If you cannot reach the plugs without removing other engine parts, or if your vehicle has coil-on-plug ignition, the job is better left to a mechanic.

Gather the right tools and parts before you start

You need a spark plug socket (a deep socket with a rubber insert that grips the plug), a ratchet that fits your socket, a gap tool (a small metal gauge that measures and adjusts the space between the plug's electrodes), and the correct new plugs for your vehicle. A spark plug socket is not the same as a regular deep socket — the rubber insert keeps the ceramic insulator from cracking when you remove or install the plug. You can buy a socket and gap tool together for $10 to $20 at any auto parts store.

Buy plugs one at a time or in a set, depending on how many your engine has. Most four-cylinder engines have four plugs; six-cylinder engines have six; eight-cylinder engines have eight. The box will list the vehicle year, make, model, and engine size — match all of these before you buy. If you're unsure, bring your vehicle's VIN (visible on the dashboard at the driver's side windshield) to the parts counter and they will pull the exact part number.

Let your engine cool for at least 30 minutes before you start. Hot engine parts can burn your hands, and you risk cracking a ceramic insulator if you remove a plug from a hot engine.

Remove the old plugs one at a time

Open your hood and locate the spark plugs. On most vehicles, you'll see thick wires or coils sitting on top of the engine. Each wire or coil connects to one plug. Start with the plug closest to you or the one easiest to reach. Gently twist and pull the wire or coil boot (the rubber connector) straight up — do not yank it sideways, which can damage the connection. If the boot is stuck, rock it gently side to side while pulling.

Once the wire or coil is off, use your spark plug socket and ratchet to unscrew the old plug. Turn counterclockwise until the plug comes free. Set it aside — you may need it later if something goes wrong. Look inside the hole where the plug was. If you see heavy black buildup, rust, or oil, your engine may have a larger problem worth discussing with a mechanic before you continue.

Do not remove all the plugs at once. Remove one, install the new one, and reconnect the wire or coil before moving to the next plug. This prevents you from mixing up which wire goes to which cylinder, which will cause the engine to misfire or not start.

Check and set the gap on the new plug

The gap is the space between the center electrode and the side electrode on the tip of the plug. Your owner's manual or the sticker under your hood lists the correct gap in thousandths of an inch (for example, 0.040 inch). Most new plugs come pre-gapped to a common setting, but it may not be the right one for your engine. Checking takes 30 seconds and prevents a misfire.

Use your gap tool to measure the space. The tool has a wire or blade that slides between the electrodes. If the gap is too small, gently tap the side electrode against a hard surface to widen it. If the gap is too large, carefully bend the side electrode inward. Make small adjustments — a gap that is off by 0.010 inch will cause problems. Once the gap is correct, the plug is ready to install.

Install the new plug and reconnect the wire or coil

Carefully thread the new plug into the hole by hand first. This prevents you from cross-threading it, which damages the hole and can cost hundreds to repair. Once the plug is hand-tight, use your ratchet and socket to tighten it the rest of the way. Spark plugs are not bolts — they only need to be snug, not cranked down hard. A typical plug torque is 15 to 20 foot-pounds; if you have a torque wrench, use it. If you don't, tighten until you feel resistance and stop.

Reconnect the wire or coil boot by pushing it straight down onto the plug until you hear or feel a click. The boot should sit flush against the plug. If it doesn't, the connection is loose and the plug won't fire. Gently tug the boot to make sure it's seated.

Now move to the next plug. Repeat the process: remove the wire or coil, unscrew the old plug, check and set the gap on the new one, install it, and reconnect the wire or coil. Work through all the plugs in this order to avoid confusion.

Start the engine and check for misfires

Once all plugs are installed and all wires or coils are reconnected, close the hood and start the engine. It should start normally and idle smoothly. If the engine cranks but won't start, or if it starts but runs rough or shakes, you likely have a misfire. The most common cause is a wire or coil that is not fully seated on a plug, or plugs installed in the wrong order.

Turn off the engine and check each wire or coil connection. Push down firmly on each boot to make sure it is fully seated. If one was loose, reconnect it and try starting again. If the engine still misfires, turn it off and check that you installed the plugs in the correct cylinders. Your owner's manual shows the firing order — for example, 1-3-4-2 means the plugs fire in that sequence. If you removed all the plugs at once and reconnected them in the wrong order, you'll need to move them to the correct cylinders.

If the engine starts and runs smoothly, the job is done. Take the vehicle for a short drive to confirm everything is working normally.

When to take your car to a mechanic instead

Some vehicles make spark plug replacement difficult or impossible without special tools. If your plugs are buried under the intake manifold, air filter housing, or other engine parts, removing them takes several hours and requires disassembling the engine. If your vehicle has coil-on-plug ignition (a coil mounted directly on each plug instead of a wire), the coils can be fragile and expensive to replace if you crack one.

If you start the job and find that you cannot reach a plug, or if you crack a ceramic insulator while removing a plug, stop and take the vehicle to a mechanic. Continuing could cause more damage. A mechanic has the right tools, the experience to work quickly, and the knowledge to spot other problems while the plugs are out.

Frequently Asked Questions

How do I know which spark plug wire goes to which cylinder?

Your owner's manual shows the firing order and which cylinder is which on your engine. Most manuals also have a diagram showing which wire connects to which plug. If you removed all the wires at once, take a photo of the engine before you start so you can reference it. Alternatively, remove and install one plug at a time so you never lose track of which wire goes where.

Can I use a different type of spark plug than the manual recommends?

You should use the type your manual specifies. Using the wrong type can cause misfires, poor fuel economy, or hard starting. The manual recommends a specific plug because that plug is designed to fire at the right temperature and voltage for your engine. Upgrading to a higher-quality plug (like iridium instead of copper) is fine if the part number matches your vehicle, but downgrading to a cheaper type is not.

What if I cannot get the old spark plug out?

If a plug is stuck, explore a penetrating oil like WD-40 around the base of the plug and wait 15 to 30 minutes. Try again gently — do not force it, which can break the plug inside the hole. If it still won't budge, stop and take the vehicle to a mechanic. A stuck plug usually means the threads are damaged, and a mechanic has the tools to remove it without causing more damage.

Do I need to replace the spark plug wires or coils at the same time?

No, unless they are damaged or your vehicle has high mileage (over 100,000 miles) and the wires are original. Wires and coils last much longer than plugs. If your engine runs rough after you replace the plugs, the wires or coils may be the problem, but replace the plugs first and confirm they are the issue before buying new wires or coils.

How often should I replace my spark plugs?

Check your owner's manual for the recommended interval. Copper plugs typically last 30,000 miles, platinum plugs 50,000 to 100,000 miles, and iridium plugs 100,000+ miles. Some newer vehicles have plugs rated for 120,000 miles or more. If you drive in dusty conditions or tow frequently, plugs may wear out faster. Your mechanic can inspect them during a routine service and tell you if they need replacement sooner.