What degreeing a camshaft means and why it matters
Degreeing a camshaft is the process of setting the exact rotational position of the cam relative to the crankshaft so that the valve opening and closing events happen at the precise moments the engine was designed for. When a camshaft is installed, it can slip a few degrees during the process, or you may intentionally offset it to change the engine's power band. Without degreeing, your intake and exhaust valves open and close at the wrong times, which costs you power, fuel economy, and reliability.
The camshaft controls when valves open and close through its lobes — the egg-shaped protrusions that push on valve lifters or rocker arms. The crankshaft turns twice for every complete cycle of the camshaft, so timing between them has to be exact. A variance of just a few degrees can shift peak horsepower to a different RPM range or make cold starts harder. Degreeing catches these errors before they affect how the engine runs.
Key Takeaways
- Degreeing requires a degree wheel bolted to the crankshaft, a dial indicator mounted to track cam lobe movement, and a way to measure crankshaft position — usually a pointer and timing marks.
- The process involves rotating the engine to find the exact point where each intake and exhaust lobe reaches maximum lift, then comparing that position to what the cam card specifies.
- Most street engines are degreeed at a fixed point like top dead center (TDC) on the number one cylinder, while race engines may be degreeed at multiple points across the RPM range.
- If your cam is off by more than 2 to 3 degrees from specification, you should remove it and reinstall it with the correct offset, or use an adjustable timing gear to correct it.
- Degreeing is most critical when you install a performance camshaft, but it is also worth checking on any engine rebuild where the cam or timing chain has been disturbed.
Tools and equipment you will need
Start with a degree wheel — a large disc marked with degree increments (usually 0 to 360) that bolts to the front of the crankshaft. You can buy one as part of a degreeing kit, or make one from a printed template and plywood. The wheel needs to be perfectly centered on the crankshaft and locked so it does not slip during the process.
You will also need a dial indicator (also called a dial gauge) mounted on a stand or magnetic base so it can track the vertical movement of a cam lobe as the engine rotates. The indicator needle should rest on the highest point of the lobe you are measuring. A pointer — a straightforward metal rod or bracket — mounts to the engine block or timing cover and points to the degree wheel so you can read the crankshaft position at any moment.
Additional items include a socket and breaker bar to rotate the engine by hand, a cam card (the specification sheet that came with your camshaft showing the exact opening and closing points), and a way to lock the crankshaft in place — either a crankshaft lock tool or a bolt through the harmonic balancer. Some shops use a dial indicator on the crankshaft itself instead of a pointer and degree wheel, but the principle is the same.
Finding top dead center before you start
Before you install the degree wheel, you must find top dead center (TDC) on the number one cylinder — the point where the piston is at its highest point in the bore and both valves are closed. This is your reference point for all measurements. Rotate the engine by hand using the breaker bar until the timing marks on the crankshaft and timing cover align, or use a piston stop tool inserted into the number one spark plug hole to lock the piston at the top of its stroke.
Once the piston is at TDC, mark the crankshaft and timing cover with a marker or paint pen so you can return to this position if the engine rotates. Install the degree wheel so that the 0-degree mark points straight up (or points to your pointer, depending on your setup). Lock the wheel to the crankshaft with a bolt so it cannot move. Double-check that the wheel is centered and does not wobble — any runout will throw off your readings.
Measuring intake lobe opening and closing points
Mount the dial indicator so the plunger rests on the highest point of the intake lobe you are measuring. Rotate the engine slowly by hand in the direction it normally runs (usually clockwise when viewed from the front). Watch the dial indicator needle as the lobe rises and falls. The needle will climb as the lobe approaches, peak when the lobe is at maximum height, and drop as the lobe passes.
Note the degree wheel reading when the needle first moves (this is the opening point) and when it returns to zero after the peak (this is the closing point). Write these numbers down. The difference between opening and closing is the duration — how long the valve stays open, measured in degrees of crankshaft rotation. Compare your readings to the cam card. If the intake opens at 12 degrees before TDC on the card but your measurement shows 15 degrees, the cam is 3 degrees advanced (opening earlier than it should).
Measuring exhaust lobe opening and closing points
Repeat the same process for the exhaust lobe on the same cylinder. Mount the dial indicator on the exhaust lobe, rotate the engine, and record the opening and closing points. Exhaust typically opens before the piston reaches bottom dead center (BDC) and closes after TDC on the next cycle, so your readings may include negative numbers or numbers above 180 degrees — that is normal and expected.
Again, compare your measurements to the cam card. The exhaust lobe is usually less sensitive to small timing errors than the intake, but it should still be within 2 to 3 degrees of specification. If both lobes are off by the same amount in the same direction, the entire camshaft is advanced or retarded by that amount, which means it slipped during installation or the timing gear is not centered correctly.
Correcting timing if the cam is out of spec
If your measurements are within 1 to 2 degrees of the cam card, you can usually leave the cam as-is — manufacturing tolerances and measurement error at that scale will not noticeably affect how the engine runs. If the cam is off by 3 degrees or more, you have two options: remove the camshaft and reinstall it with the correct offset, or use an adjustable timing gear to shift the cam position without removing it.
Removing and reinstalling the cam is the most reliable method but requires draining coolant, removing the timing cover, and potentially disturbing other components. An adjustable timing gear (also called a vernier gear or adjustable sprocket) has slots that allow you to shift the cam a few degrees relative to the crankshaft without taking anything apart. Loosen the bolts, rotate the gear slightly, and re-measure. This method works well for small corrections and is common on performance builds where fine-tuning the power band is the goal.
When to degree a cam and when to skip it
Degreeing is essential when you install a performance or race camshaft, especially if you are using an adjustable timing gear or if the cam is a tight-lobe design where a few degrees makes a real difference. It is also worth doing on any engine rebuild where the timing chain, gears, or camshaft have been removed and reinstalled, because slippage during assembly is common.
On a stock engine with a factory camshaft that has never been removed, degreeing is usually unnecessary — the cam was timed correctly at the factory and has not moved. However, if you are chasing a performance issue or trying to optimize fuel economy, degreeing can reveal whether a previous repair or modification threw off the timing. Many engine builders include degreeing as part of their standard rebuild process because the cost of the time is small compared to the cost of a poorly running engine.
Frequently Asked Questions
Can I degree a cam without removing the valve covers?
Yes. You need access to the front of the engine to install the degree wheel and pointer, and access to the top to mount the dial indicator on the cam lobes. You do not need to remove the valve covers themselves — just enough clearance to reach the lobes with the indicator. On some engines you may need to remove the intake manifold or other accessories to get the dial indicator in position.
What if my dial indicator does not fit between the rocker arm and the lobe?
Use a dial indicator with a longer stem, or mount it at an angle so the plunger approaches the lobe from the side rather than straight down. Some builders use a small block of aluminum or steel as a spacer to move the indicator further away from the engine. The key is that the plunger must rest on the highest point of the lobe and move freely as the lobe rotates.
How many degrees of error is acceptable?
Most engine builders accept 1 to 2 degrees of error without correction. Beyond 3 degrees, the timing is far enough off that it will affect idle quality, power delivery, or fuel economy. Race engines are often held to tighter tolerances — within 0.5 to 1 degree — because the cam profile is optimized for a narrow RPM range where precision matters more.
Do I need to degree the cam if I am just replacing a timing chain?
Only if the camshaft or crankshaft sprocket was removed during the job. If you replaced the chain without disturbing the cam or crank gears, the timing is still correct. If either sprocket came off, you should at least verify that the timing marks line up correctly before you start the engine, and degreeing is a good idea if you want to be thorough.
Can I degree a cam with the engine running?
No. The engine must be off and rotated by hand so you can control the speed and stop at exact positions. Running the engine while the dial indicator is on the lobe risks breaking the indicator or damaging the cam. Always rotate by hand with the ignition off and the spark plugs removed so the engine turns freely.