The 5.7 Hemi firing order is 1-8-4-3-6-5-7-2
The firing order is the sequence in which the spark plugs ignite the fuel in each cylinder. For the 5.7 Hemi engine found in Dodge Ram trucks, Jeeps, and Chrysler vehicles, that sequence is 1-8-4-3-6-5-7-2. This order matters because it keeps the engine balanced, prevents knocking, and ensures smooth power delivery across all eight cylinders.
The cylinders are numbered 1 through 8, with cylinders 1, 2, 3, and 4 on the driver's side and cylinders 5, 6, 7, and 8 on the passenger side. Cylinder 1 is at the front of the engine on the driver's side. If you get the firing order wrong—whether during a tune-up, spark plug replacement, or after removing the valve covers—your engine will run rough, misfire, or not start at all.
Key Takeaways
- The 5.7 Hemi firing order is 1-8-4-3-6-5-7-2, and getting it wrong causes misfires and rough running.
- Cylinders 1-4 are on the driver's side with cylinder 1 at the front; cylinders 5-8 are on the passenger side with cylinder 5 at the front.
- You need the correct firing order when replacing spark plugs, spark plug wires, or coil packs, or when reconnecting ignition components after engine work.
- The distributor cap (on older models) or coil pack arrangement must match the firing order, or the engine will not run correctly.
Why the firing order matters for engine performance
The firing order controls the timing of combustion in each cylinder. If cylinders fire in the wrong sequence, the crankshaft receives power strokes at the wrong moments, causing vibration, loss of power, and engine knock. A 5.7 Hemi running on the wrong firing order will feel like it is bucking or surging, especially under load.
The firing order also affects how the engine's cooling and lubrication systems work. When combustion happens in the right sequence, heat and wear are distributed evenly across all cylinders. When it is wrong, some cylinders run hotter than others, leading to premature wear and potential damage to pistons and rings.
Cylinder numbering on the 5.7 Hemi
The 5.7 Hemi is a V8 engine with two banks of four cylinders each. On the driver's side (left bank), you have cylinders 1, 2, 3, and 4 from front to back. On the passenger's side (right bank), you have cylinders 5, 6, 7, and 8 from front to back. Cylinder 1 is always the reference point—it is the first cylinder to fire in the sequence.
When you are looking at the engine from the front of the vehicle, the driver's side is on your left and the passenger's side is on your right. This matters because when you are working on spark plugs or wires, you need to know which physical cylinder you are touching and match it to the correct position in the firing order.
Connecting spark plug wires and coil packs in the right order
On older 5.7 Hemi engines with a distributor and spark plug wires, the distributor cap has eight terminals arranged in a circle. The rotor inside the distributor spins and touches each terminal in the firing order sequence: 1-8-4-3-6-5-7-2. The spark plug wires must be connected from the distributor cap to the spark plugs in this exact order, or the engine will not fire correctly.
On newer 5.7 Hemi engines (2003 and later), there is no distributor. Instead, each spark plug has its own coil pack mounted directly on top. The engine computer controls when each coil fires based on the crankshaft position sensor. However, you still need to understand the firing order if you are replacing coil packs, because you need to know which coil controls which cylinder.
When replacing spark plug wires or coil packs, remove and install one at a time rather than pulling them all off at once. This prevents mixing them up. If you do remove them all, take a photo of the original setup before you start, or write down which wire or coil goes to which cylinder.
What happens when the firing order is wrong
An engine running on the wrong firing order will exhibit several clear symptoms. The engine may not start at all, or it may start and when ready stall. If it does run, it will idle roughly, hesitate under acceleration, and produce a loud knocking sound. You may also see a check engine light on the dashboard.
The engine may backfire through the exhaust or intake, sending flames or pops out of the tailpipe. This happens because fuel is igniting at the wrong time in the combustion cycle. Continued driving on the wrong firing order can damage the catalytic converter, spark plugs, and internal engine components.
Steps to verify or correct the firing order
If you suspect the firing order is wrong, start by checking your work. Look at the spark plug wires or coil packs and trace each one back to the distributor cap or engine computer connection. Write down which wire or coil is connected to which cylinder, then compare it to the correct sequence: 1-8-4-3-6-5-7-2.
If you are working with spark plug wires and a distributor, rotate the engine until the rotor points to the number 1 terminal on the distributor cap. This is the starting point. Then, moving clockwise around the cap, the terminals should be arranged so that the rotor touches them in the firing order sequence. If they are not, the wires are in the wrong positions.
For coil pack engines, consult your vehicle's service manual or the coil pack labels to confirm which coil controls which cylinder. The coils are usually labeled or color-coded. If you have removed them, reinstall them one at a time using the manual as your guide.
Tools and resources you will need
To work on the 5.7 Hemi firing order, you will need a service manual specific to your vehicle's year and model. Dodge, Jeep, and Chrysler service manuals are available from dealerships or online retailers. The manual will include a diagram showing the cylinder numbering, the firing order, and the correct wire or coil positions.
You may also want a spark plug wire set or coil pack set designed for your specific year and engine. OEM (original equipment manufacturer) parts are usually more reliable than aftermarket alternatives, though quality aftermarket parts are available. A timing light can help you verify that the engine is firing at the correct moment, though this is more advanced work.
Frequently Asked Questions
Can I drive my truck if the firing order is wrong?
No. An engine on the wrong firing order will run very poorly, misfire constantly, and may not start at all. Driving it risks damage to the catalytic converter and engine internals. Stop driving and correct the firing order before operating the vehicle.
Does the firing order change if I have a modified or turbocharged 5.7 Hemi?
No. The firing order remains 1-8-4-3-6-5-7-2 regardless of modifications. The firing order is determined by the engine's internal design and crankshaft configuration, not by performance upgrades.
What is the difference between firing order and ignition timing?
Firing order is the sequence in which cylinders ignite. Ignition timing is the moment in the engine cycle when each spark plug fires. Both matter, but they are separate. You can have the correct firing order but wrong timing, which also causes rough running.
Do I need to reset anything after changing spark plug wires?
On older 5.7 Hemi engines with a distributor, no reset is needed. On newer coil pack engines, the computer may log a misfire code if you accidentally swapped wires. Clear the code with a diagnostic scanner after you have confirmed the wires are in the correct positions.
Where can I find the firing order diagram for my specific truck?
The firing order diagram is in your vehicle's service manual, usually in the engine section. You can also find it on the emissions label under the hood, though not all vehicles include it there. Dodge and Jeep dealerships can provide the manual, or you can purchase one from online retailers.