The firing order for a small block Chevy is 1-8-4-3-6-5-7-2
The firing order is the sequence in which spark plugs ignite the fuel mixture in each cylinder. For small block Chevrolet engines — the 262, 283, 305, 327, 350, and 400 cubic inch models — that sequence is always 1-8-4-3-6-5-7-2. This order matters because connecting the spark plug wires in the wrong sequence will prevent the engine from running, or cause it to run so poorly that it won't stay running.
The firing order is determined by the engine's crankshaft design and the position of the cylinders. You cannot change it, and it does not vary between years or models within the small block family. What does change is which physical cylinder gets which number — and that is where most mistakes happen.
Key Takeaways
- Small block Chevy firing order is always 1-8-4-3-6-5-7-2, but cylinder numbering depends on whether you are looking at the driver's side or passenger's side of the engine.
- On small blocks, cylinders 1, 2, 3, and 4 are on the passenger's side (right side), and cylinders 5, 6, 7, and 8 are on the driver's side (left side), when facing the engine from the front.
- The distributor cap has a marked position for cylinder 1, and the rotor must point to that position when the number 1 piston is at top dead center.
- Spark plug wires must follow the firing order around the distributor cap in the direction the rotor spins, which is clockwise on small block Chevys.
- Incorrect wire placement causes a no-start condition, rough idle, backfiring, or severe loss of power.
How cylinder numbers are positioned on a small block Chevy
Cylinder numbering on a small block Chevy is not left-to-right or front-to-back. Instead, the engine is divided into two banks. Cylinders 1, 2, 3, and 4 sit on the passenger's side (right side) of the engine when you face it from the front. Cylinders 5, 6, 7, and 8 sit on the driver's side (left side). Within each bank, the cylinders are numbered from front to back: 1 and 5 are at the front, 4 and 8 are at the back.
This layout is standard across all small block Chevys. The confusion usually starts because people expect the cylinders to be numbered in a different pattern — often left-to-right or in the order they appear on the distributor cap. They are not. Write down or mark the cylinder positions on your engine before you touch the spark plug wires, especially if you are working on an unfamiliar vehicle.
Finding cylinder 1 and setting the distributor
The distributor cap has a marked position for cylinder 1. On most small block Chevys, this mark is a notch, a raised bump, or a printed number on the cap itself. Before you install any spark plug wires, you must position the rotor so it points directly at the cylinder 1 terminal when the number 1 piston is at top dead center (TDC) on the compression stroke.
To find top dead center, remove the number 1 spark plug and place your thumb over the hole. Rotate the engine by hand (using a wrench on the crankshaft bolt) until you feel pressure building under your thumb — that is the compression stroke. Keep rotating slowly until the timing mark on the crankshaft pulley aligns with the zero mark on the timing cover. At this point, the number 1 piston is at TDC on compression, and the rotor should point at the cylinder 1 terminal on the distributor cap.
If the rotor does not point at cylinder 1, the distributor is installed 180 degrees out. Remove it, rotate it halfway around, and reinstall it. Check again. This step is critical because the entire firing order depends on getting cylinder 1 correct.
Installing spark plug wires in firing order sequence
Once the rotor points at cylinder 1 with the piston at TDC, you can install the spark plug wires. The rotor spins clockwise on a small block Chevy. Starting at the cylinder 1 terminal on the distributor cap, move clockwise around the cap and install wires in the firing order: 1-8-4-3-6-5-7-2.
This means the wire from cylinder 1 goes to the cylinder 1 terminal. The next wire, going clockwise around the cap, goes to cylinder 8. The next goes to cylinder 4, and so on. Each wire connects the spark plug on that cylinder to its corresponding terminal on the cap. If you install them out of order, the engine will not fire in the correct sequence, and it will not run.
A common mistake is to install the wires in numerical order (1-2-3-4-5-6-7-8) around the cap. This is wrong. The firing order is not the same as the cylinder numbering order. Write the firing order on a piece of tape and stick it to the engine block while you work, so you can check each wire before you install it.
What happens when the firing order is wrong
An incorrect firing order produces when ready and obvious symptoms. The engine will either not start at all, or it will start and run so rough that it dies within seconds. You may hear backfiring through the intake or exhaust, or see the engine bucking and shaking.
If the engine starts but runs poorly, do not drive it. Continuing to run an engine with the wrong firing order can damage the catalytic converter and other emissions equipment. Stop, turn off the engine, and recheck the spark plug wire positions against the firing order. In most cases, one or two wires are straightforward in the wrong position, and moving them to the correct terminals will fix the problem when ready.
Checking your work before starting the engine
Before you start the engine, trace each spark plug wire from the plug to the distributor cap terminal and verify it matches the firing order. A straightforward way to do this is to number each wire with tape or a marker before you remove the old wires, so you have a reference if you need to reinstall them.
If you are replacing the distributor or the spark plug wires, take a photo of the original wire positions on the old cap before you remove anything. This gives you a visual reference if you get confused during installation. Many people also draw a diagram of the cap with the cylinder numbers and firing order written in, then use that diagram to install the new wires one at a time.
Double-check that each wire is fully seated on both the spark plug and the distributor cap terminal. A loose connection will cause a misfire or a no-start condition that looks identical to an incorrect firing order.
Small block Chevy firing order reference table
| Firing Order Position | Cylinder Number | Location |
|---|---|---|
| 1st | 1 | Passenger's side, front |
| 2nd | 8 | Driver's side, rear |
| 3rd | 4 | Passenger's side, rear |
| 4th | 3 | Passenger's side, middle-rear |
| 5th | 6 | Driver's side, middle-rear |
| 6th | 5 | Driver's side, front |
| 7th | 7 | Driver's side, middle-front |
| 8th | 2 | Passenger's side, middle-front |
Frequently Asked Questions
Does the firing order change if I have an HEI distributor instead of a points distributor?
No. The firing order is 1-8-4-3-6-5-7-2 regardless of the distributor type. HEI and points distributors have the same cap layout and cylinder terminal positions. The only difference is the internal ignition mechanism, not the firing sequence.
What if I cannot find the cylinder 1 mark on my distributor cap?
Check the distributor housing itself — some caps do not have a mark, but the housing has a notch or line that indicates cylinder 1. If neither the cap nor the housing is marked, consult the service manual for your specific engine year and model. You can also count the terminals: cylinder 1 is typically at the 5 o'clock or 6 o'clock position when the distributor is installed in the engine.
Can I install the distributor 180 degrees out and just reverse the firing order?
No. The firing order is fixed by the engine's crankshaft and cam design. Installing the distributor backwards will cause the engine to fire at the wrong time in the combustion cycle, and it will not run. Always install the distributor so the rotor points at cylinder 1 when the number 1 piston is at top dead center on compression.
What if one spark plug wire keeps coming loose from the distributor cap?
The terminal inside the cap may be worn or corroded. Try a new spark plug wire with a fresh terminal. If the problem continues, the distributor cap itself may need replacement. A loose wire connection will cause a misfire that feels similar to an incorrect firing order, so verify the wire is fully seated before assuming the cap is bad.
Does the firing order matter for a carbureted engine versus a fuel-injected engine?
Yes, the firing order is the same for both. The firing order depends only on the engine's mechanical design, not on how fuel is delivered or how the ignition is controlled. A carbureted 350 and a fuel-injected 350 have the same firing order: 1-8-4-3-6-5-7-2.