What a crank angle sensor does and why it fails
A crank angle sensor (also called a crankshaft position sensor) tells your engine's computer where the crankshaft is in its rotation. The computer uses this information to time the spark plugs and fuel injectors correctly. Without an accurate signal, your engine won't start, will run rough, or will shut off while driving.
The sensor sits near the crankshaft, usually on the engine block or inside the distributor, and reads a toothed ring or magnet as the shaft spins. Over time, the sensor's wiring corrodes, the connector fills with moisture, or the sensor itself wears out. A failed sensor produces a check engine light and often a P0335 or P0336 diagnostic code.
Replacing one is a job most owners can do at home with basic tools, though the location varies widely by vehicle make and model. Some sensors take 15 minutes; others require removing the distributor or timing cover.
Key Takeaways
- The crank angle sensor location depends on your vehicle — check your repair manual or search your specific year, make, and model online before starting.
- You will need a socket set, screwdrivers, a new sensor, and possibly a timing light or diagnostic scanner to confirm the old sensor is actually faulty.
- Disconnect the negative battery terminal before you begin to avoid electrical shorts and accidental airbag deployment.
- After installation, clear the check engine light with a scanner or by disconnecting the battery for 15 minutes, then test-drive to confirm the code does not return.
Locate the sensor on your specific vehicle
The crank angle sensor location is not standard across manufacturers. On some vehicles it bolts to the front of the engine block near the crankshaft pulley. On others it sits inside the distributor cap, and on some it mounts to the transmission bell housing or the rear of the engine block.
Your best source is the repair manual for your exact year, make, and model. If you do not have one, search online for "[your year] [make] [model] crank angle sensor location" or "crankshaft position sensor location" — forums and YouTube videos for your vehicle often show the exact spot and the steps to reach it.
Write down the location before you start. Some sensors are visible and accessible in five minutes; others require removing the air intake, radiator hose, or timing cover. Knowing this in advance saves you from halfway through the job realizing you need a lift or a second person.
Gather tools and confirm the sensor is faulty
You will need a socket set (usually 8mm to 14mm), screwdrivers (Phillips and flat-head), a new sensor matched to your vehicle, and a jack and jack stands if the sensor is underneath the car. Have a drain pan nearby if the sensor is near coolant lines.
Before you remove anything, confirm the sensor is actually the problem. A check engine light and a P0335, P0336, or P0337 code point to the sensor, but a loose connector, corroded wiring, or a bad alternator can trigger the same codes. If you have access to a diagnostic scanner, clear the code, drive the vehicle, and see if it returns. If the code comes back when ready, the sensor is likely faulty. If you do not have a scanner, many auto parts stores will read the code for free and can tell you whether the sensor or the wiring is the likely culprit.
A faulty sensor usually cannot be repaired — you replace it. Sensors cost between $50 and $300 depending on the vehicle, and most are not returnable once opened.
Disconnect the battery and remove the old sensor
Open the hood and disconnect the negative (black) battery terminal using a wrench. This prevents electrical shorts and accidental airbag deployment if you bump a connector. Wait a few minutes for the engine to cool if you have been driving.
Locate the sensor connector and unplug it by pressing the release tab or clip. Some connectors are tight — wiggle gently rather than pulling hard. Take a photo of the connector orientation before you unplug it so you know which way the new one goes in.
Unbolt the sensor using the appropriate socket or wrench. Most sensors are held by one or two bolts. Keep the bolts in a small container so you do not lose them. If the sensor is stuck, spray penetrating oil around the base and wait 10 minutes before trying again. Do not force it — a broken bolt left in the engine block is a much bigger problem.
Install the new sensor and reconnect the battery
Before you install the new sensor, check that the mounting surface is clean and free of oil or corrosion. Wipe it with a clean rag if needed. Some sensors come with a gasket or O-ring; do not remove it unless the instructions say to.
Insert the new sensor into the mounting hole and hand-tighten the bolts first. Once you are sure it is seated correctly, tighten the bolts with a socket wrench. Do not over-tighten — most sensors need only 15 to 25 foot-pounds of torque. If you do not have a torque wrench, tighten until snug and then stop.
Plug the connector back in, making sure it clicks or locks into place. Reconnect the negative battery terminal. Do not start the engine yet.
Clear the check engine light and test the repair
The check engine light will usually turn off on its own after a few engine starts, but you can clear it faster with a diagnostic scanner. If you have one, plug it in, select "Clear Codes," and confirm the light goes out. If you do not have a scanner, disconnect the negative battery terminal again and leave it disconnected for 15 minutes. This will clear the code, though it will also reset your radio presets and clock.
Start the engine and listen for rough idle, misfires, or unusual sounds. If the engine starts and idles smoothly, take a short test drive at normal speeds. The check engine light should stay off. If it comes back on within a few minutes, the sensor may be defective, the connector may not be fully seated, or there may be a wiring problem. Stop driving and recheck the connector and bolt torque.
If the light stays off and the engine runs normally, the repair is complete. Drive the vehicle for at least 50 miles to confirm the code does not return. Some vehicles need to complete a full drive cycle (a mix of highway and city driving) before the computer is satisfied that the sensor is working correctly.
When to call a mechanic instead
If the sensor is inside the distributor, you may need to remove the entire distributor, which requires timing the engine afterward. This is a job for someone with experience or a mechanic. Similarly, if the sensor is behind the timing cover or requires removing the engine oil pan, the labor cost often makes professional service the better choice.
If you remove the old sensor and find the mounting hole is stripped or the bolt will not come out, stop and take the vehicle to a shop. Forcing a stripped bolt or a stuck sensor can crack the engine block or transmission housing.
If you install the new sensor, clear the code, and the check engine light comes back on within a few days, the sensor may be defective or there may be a wiring or connector issue that requires a scanner to diagnose. At that point, a mechanic with diagnostic equipment is your best option.
Frequently Asked Questions
How do I know if my crank angle sensor is bad?
A faulty sensor usually triggers a check engine light with a P0335, P0336, or P0337 code. You may also notice the engine will not start, runs rough at idle, stalls while driving, or loses power under acceleration. A diagnostic scanner can confirm the code, and many auto parts stores will read it for free.
Can I drive with a bad crank angle sensor?
Not safely. Without a correct signal, the engine cannot time the spark plugs or fuel injectors properly. The engine may start and run briefly, but it will stall, misfire, or shut off without warning. Do not drive the vehicle until the sensor is replaced.
How long does it take to replace a crank angle sensor?
If the sensor is easily accessible, replacement takes 15 to 30 minutes. If it is inside the distributor or behind the timing cover, the job can take one to three hours. Check your repair manual or a video for your specific vehicle to get a realistic time estimate before you start.
Do I need to replace the connector or wiring when I replace the sensor?
Only if the connector is cracked, the wiring is frayed, or corrosion is visible. In most cases, unplugging the old connector and plugging in the new sensor is all you need. If the connector looks corroded, clean it with electrical contact cleaner before you plug in the new sensor.
Will the check engine light turn off automatically after I replace the sensor?
Usually, yes — the light will turn off after a few engine starts once the computer confirms the sensor is working. You can clear it faster with a diagnostic scanner, or by disconnecting the battery for 15 minutes. The light should stay off if the sensor is installed correctly and functioning.