What a crank sensor does and why it matters
Your crank sensor tells your engine's computer where the crankshaft is and how fast it's spinning. The engine uses this information to time the fuel injection and spark plugs. When a crank sensor fails, your engine may not start, may stall while driving, or may run rough and trigger a check engine light.
A failing crank sensor is one of the most common reasons an engine won't turn over or cuts out unexpectedly. You can test it yourself with basic tools before paying a shop to diagnose the problem.
Key Takeaways
- A crank sensor failure usually shows up as a no-start condition, rough idle, stalling, or a check engine light with code P0335 or similar.
- You can test a crank sensor with a multimeter set to resistance mode, though the exact procedure varies by sensor type and vehicle model.
- Most crank sensors sit near the crankshaft pulley or flywheel, but location varies widely — your vehicle's service manual shows the exact spot.
- If the sensor reads outside the manufacturer's resistance range or shows no signal on an oscilloscope, replacement is usually the next step.
- Some vehicles require a scan tool to read live sensor data, which means a shop test may be necessary if you don't have access to one.
Locate your crank sensor
The crank sensor location depends on your vehicle's make, model, and year. Most sit near the crankshaft pulley at the front of the engine, near the flywheel at the rear, or inside the distributor. Some vehicles have more than one.
Your best source is the vehicle's service manual or a repair database like AllData or Haynes. If you don't have the manual, search online for "[your year/make/model] crank sensor location" — you'll usually find a diagram or photo showing exactly where to look. Once you find it, note whether it's a two-wire, three-wire, or Hall-effect sensor, because the test method differs.
Test resistance with a multimeter
Disconnect the negative battery terminal first. Locate the crank sensor connector and unplug it. Set your multimeter to the resistance (ohms) setting, usually marked with the Greek letter omega (Ω).
Touch one probe to each terminal of the sensor itself — not the connector. A good sensor typically reads between 200 and 900 ohms, though the exact range depends on the manufacturer. Check your service manual or the sensor's part number online to find the correct range for your vehicle. If the reading is zero, very high, or unstable, the sensor is likely bad.
Some sensors are non-contact types and won't show a resistance reading at all. If your sensor has no resistance specification, you'll need to move to the voltage test or use a scan tool.
Check voltage output while cranking
Reconnect the sensor and battery. Set your multimeter to DC voltage mode. Locate the signal wire on the sensor connector — this is usually the middle wire on a three-wire sensor or one of two wires on a two-wire type. Your service manual will identify which one.
Backprobe the signal wire by inserting a small pin or needle through the connector without disconnecting it, then touch your multimeter probe to the pin. Have someone crank the engine while you watch the meter. A working sensor should show a voltage that changes as the engine cranks — typically between 0.5 and 5 volts, fluctuating rapidly. If the voltage is steady, zero, or doesn't change, the sensor is not sending a signal.
If the engine won't crank at all, you can't perform this test. In that case, move to the resistance test or take the vehicle to a shop with a scan tool.
Use a scan tool to read live data
A scan tool connects to your vehicle's diagnostic port and reads real-time sensor data. This is the most reliable way to confirm a crank sensor problem, but it requires equipment most home mechanics don't own.
If you have access to a scan tool or a friend who does, connect it and look for the crank sensor signal while the engine is running or cranking. The tool will show whether the sensor is sending data to the computer. Some tools also display a waveform that shows the sensor's output pattern — a good sensor produces a clean, regular wave, while a failing one shows noise or drops out.
Many auto parts stores offer free scan tool readings. Bring your vehicle in and ask them to read the crank sensor data. They can tell you whether the sensor is responding and whether any fault codes are stored.
Interpret check engine codes
If your check engine light is on, the fault code will point you toward the problem. Codes P0335, P0336, P0337, and P0338 all relate to the crank sensor or its signal. P0335 means "Crankshaft Position Sensor A Circuit," which is the most common crank sensor code.
You can read the code yourself with an inexpensive code reader (around $25 to $50) or ask an auto parts store to read it for free. Write down the exact code and search for it along with your vehicle's year and model. The search results will tell you whether the code points to a sensor failure, a wiring problem, or a connector issue.
A code alone doesn't always mean the sensor is bad — a loose connector, corroded terminals, or a wiring break can trigger the same code. Check the connector and wiring before assuming the sensor itself has failed.
Check the connector and wiring
Before replacing the sensor, inspect the connector and wires. Unplug the sensor connector and look for corrosion, bent pins, or moisture inside. Clean any corrosion with electrical contact cleaner and a small brush. Reconnect and test again.
Trace the wiring from the sensor to the engine computer. Look for cuts, pinches, or damage to the insulation. If the wiring runs near hot engine parts or sharp edges, it may have been damaged over time. A damaged wire can cause the same symptoms as a bad sensor but costs far less to fix.
If the connector is clean, the wiring is intact, and your tests show no signal or out-of-range resistance, the sensor itself is likely the problem and needs replacement.
Frequently Asked Questions
Can a bad crank sensor cause a no-start condition?
Yes. Without a crank sensor signal, the engine computer can't time the fuel injectors or ignition, so the engine won't start. If your vehicle cranks but won't fire, a crank sensor failure is a common cause. A multimeter resistance test or scan tool reading will confirm whether the sensor is sending a signal.
What's the difference between a crank sensor and a cam sensor?
A crank sensor monitors the crankshaft position and speed, while a cam sensor monitors the camshaft position. Both send signals to the engine computer, but they control different functions. A failing cam sensor usually causes rough idle or starting trouble, similar to a crank sensor failure. Your vehicle may have both, and either one can cause a check engine light.
Do I need a scan tool to test a crank sensor?
No. A multimeter can test resistance and voltage output, which is enough to determine whether the sensor is working. A scan tool gives you more detailed information and is more reliable, but it's not required for a basic test. If your multimeter shows no resistance or no voltage change, the sensor is likely bad.
Can I drive with a failing crank sensor?
Not safely. A failing crank sensor can cause the engine to stall without warning, which is dangerous at highway speeds. If you suspect a crank sensor problem, have it tested and replaced before driving the vehicle regularly. Some vehicles may limp home on a backup sensor or strategy, but this is not reliable.
How much does a crank sensor replacement cost?
The sensor itself typically costs $50 to $300 depending on the vehicle, with labor adding $100 to $400 at a shop. Some vehicles have the sensor in an straightforward-to-reach spot and take 30 minutes to replace, while others require removing engine covers or other components. Check a repair estimate for your specific vehicle before deciding whether to do it yourself.