What a crank position sensor does and why it matters
Your crank position sensor tells your engine's computer where the crankshaft is at any given moment. The crankshaft is the shaft that converts the up-and-down motion of your pistons into the rotating motion that turns your wheels. Without knowing its position, your engine cannot time the spark plugs correctly or inject fuel at the right when ready. If this sensor fails, your engine will not start, will stall while driving, or will run so poorly that you cannot drive safely.
The sensor sits near the crankshaft, usually on the engine block or inside the bell housing where the transmission connects. It reads a toothed ring on the crankshaft as it spins and sends a signal to the engine control module (ECM)—the computer that runs your engine. When the sensor fails, the ECM cannot see the crankshaft position and shuts down fuel injection and ignition to protect the engine.
You can check whether the sensor is working using basic tools and a multimeter. This guide walks you through the tests you can do yourself and explains what the results mean.
Key Takeaways
- A crank position sensor failure usually triggers a check engine light and causes hard starting, stalling, or a no-start condition.
- You can locate the sensor by consulting your owner's manual or a repair manual for your specific vehicle, as the location varies widely by make and model.
- A multimeter set to AC voltage or resistance mode can tell you whether the sensor is producing a signal or has an open circuit inside.
- If the sensor reads zero voltage while cranking or shows infinite resistance, the sensor itself is likely faulty and needs replacement.
- A scope (oscilloscope) gives you a clearer picture of the signal shape, but a multimeter test is enough to rule the sensor in or out as the problem.
Locate the sensor on your engine
The crank position sensor location depends on your vehicle's make, model, and year. On some engines it bolts to the front of the block near the crankshaft pulley. On others it sits inside the bell housing between the engine and transmission, or on the back of the engine block. A few vehicles have more than one crank sensor.
Open your owner's manual and search for "crankshaft position sensor" or "crank sensor." The manual will show you the location and may include a photo or diagram. If you do not have the manual, a repair manual for your specific vehicle (available at auto parts stores or online) will have the location and a wiring diagram showing which wire is which.
Once you find it, note the wire colors and connector type. Take a photo with your phone so you can reference it later. Do not disconnect anything yet.
Disconnect the sensor and inspect it visually
Before you test with a multimeter, look at the sensor itself. Unplug the connector by squeezing or prying the tab (depending on the connector type) and gently pulling it straight out. Do not yank on the wires.
Look at the sensor tip—the end that faces the crankshaft. If it is caked with oil, metal shavings, or debris, that can block the signal. Wipe it clean with a lint-free cloth. If the tip is cracked, corroded, or visibly damaged, the sensor is faulty and must be replaced.
Check the connector pins for corrosion, bent pins, or loose contacts. If the pins look green, white, or black instead of shiny metal, corrosion is present. Gently straighten any bent pins with a small pick or needle-nose pliers. If corrosion is heavy, the connector may need to be replaced along with the sensor.
Test the sensor with a multimeter on AC voltage
Set your multimeter to AC voltage (not DC). Most crank sensors produce an alternating current signal as the toothed ring spins past them. Plug the red probe into the positive terminal and the black probe into the negative terminal of your multimeter.
Have a helper crank the engine while you hold the multimeter probes on the two signal wires of the sensor connector. Do not touch the connector itself—hold only the wires. You should see a voltage reading that changes as the engine cranks. The exact voltage varies by sensor type, but you are looking for any reading above zero that fluctuates.
If the multimeter shows zero volts while the engine is cranking, the sensor is not producing a signal. This means either the sensor is faulty, the wiring is broken, or the connector is corroded. If you see a steady voltage reading that does not change, the sensor is also not working correctly.
Test the sensor with a multimeter on resistance mode
Resistance testing tells you whether the sensor's internal coil is open (broken) or shorted. Set your multimeter to the ohms or resistance setting. Unplug the sensor connector if it is still plugged in.
Touch the two multimeter probes to the two signal wires on the sensor connector. A good sensor typically reads between 200 and 900 ohms, depending on the type. Check your repair manual for the exact specification for your sensor.
If the multimeter shows zero ohms, the coil is shorted and the sensor must be replaced. If it shows infinite resistance (usually displayed as "OL" for open line), the coil is broken and the sensor must be replaced. If the reading is within the normal range, the sensor's internal resistance is good, but this does not rule out a signal problem—you still need to do the AC voltage test while cranking.
Check the wiring and connector for faults
If the sensor itself tested good but you still got zero voltage while cranking, the problem is in the wiring or connector. Inspect the wires running from the sensor to the engine control module for cuts, pinches, or burn marks. Look where wires pass through the engine bay—they can rub against sharp edges or hot surfaces.
Reconnect the sensor connector and wiggle it gently while a helper cranks the engine. Watch the multimeter. If the voltage jumps or changes when you move the connector, the connector is loose or corroded and needs cleaning or replacement.
If you find damaged wiring, you can have it repaired by a technician, but in most cases a faulty sensor is cheaper to replace than to troubleshoot wiring problems. If the connector is corroded, you can sometimes clean it with electrical contact cleaner and a small brush, but replacement is more reliable.
Understand what your test results mean
A good crank position sensor will show a changing AC voltage (usually 0.5 to 5 volts, depending on type) when you crank the engine, and will show a resistance reading between 200 and 900 ohms when unplugged. If your sensor passes both tests, the sensor itself is working and the problem lies elsewhere—possibly in the wiring, connector, or engine control module.
If the sensor fails either test—zero voltage while cranking, infinite resistance, or zero resistance—the sensor is faulty and must be replaced. Replacement is straightforward: unbolt the old sensor, unplug it, bolt in the new one, and plug in the connector. Most sensors take 10 to 20 minutes to swap. After replacement, the check engine light should clear on its own after a few drive cycles, or you can clear it with a code reader.
If you are not comfortable using a multimeter or cannot locate the sensor, a technician can run these tests in minutes and tell you whether the sensor is the problem. This saves you time and the cost of replacing a good sensor by mistake.
Frequently Asked Questions
What does a bad crank position sensor feel like when driving?
A failing sensor usually causes hard starting, rough idle, stalling at stops, or loss of power under acceleration. You may also see a check engine light. In some cases the engine will not start at all. These symptoms can also come from other problems, so testing the sensor is the only way to know for sure.
Can I drive with a bad crank position sensor?
No. Once the sensor fails completely, the engine will not run because the computer cannot time the ignition and fuel injection. If the sensor is failing intermittently, you may be able to drive short distances, but the engine may stall without warning, which is unsafe. Have it tested and replaced as soon as possible.
How much does a crank position sensor cost to replace?
The sensor itself usually costs between $50 and $250 depending on your vehicle. Labor at a shop typically adds $100 to $300. Some sensors are straightforward to reach and take 15 minutes; others require removing other components and take an hour or more. Your owner's manual or a repair manual will tell you how long the job should take.
Will a bad crank sensor trigger a check engine light?
Yes. A faulty crank sensor almost always sets a code like P0335 (crankshaft position sensor malfunction) or P0336 (crankshaft position sensor range/performance). You can read the code with a code reader or have a shop read it for you. The code confirms the sensor is the problem.
Can a crank sensor go bad suddenly or does it fail gradually?
Both happen. Some sensors fail suddenly—one moment the engine runs fine, the next it will not start. Others fail gradually, causing intermittent stalling or rough running that gets worse over time. Corrosion or debris on the sensor tip can cause gradual failure; internal coil failure usually happens suddenly.