What a coolant temperature sensor does and why it fails
Your coolant temperature sensor sits in the engine block or radiator and tells your engine computer how hot the coolant is running. The computer uses that reading to adjust fuel mixture, ignition timing, and fan speed. When the sensor fails, you get a check engine light, poor fuel economy, rough idle, or a fan that won't kick on—leaving your engine at risk of overheating.
Sensors fail because they're exposed to constant heat cycling and corrosive coolant. Most last 100,000 to 150,000 miles, though some go longer. You'll know it's failing when the check engine light appears with a code like P0117 (coolant temp sensor low) or P0118 (coolant temp sensor high). A scan tool will confirm which code you're seeing.
Key Takeaways
- A coolant temperature sensor typically costs $15 to $80 for the part, plus $150 to $300 in labor at a shop, or you can do it yourself in 30 minutes to an hour.
- You'll need a socket wrench, a drain pan, and possibly a sensor socket or wrench—the sensor itself is usually a straightforward bolt-in part located on the engine block or thermostat housing.
- Drain some coolant before you start so you don't lose a full radiator's worth when you pull the sensor out.
- The new sensor goes in the same spot and threads in by hand first, then tightens with a wrench—no special tools or sealant required on most vehicles.
Locating your coolant temperature sensor
The sensor location varies by make and model. On most vehicles, it's mounted on the engine block near the thermostat housing, or directly in the thermostat housing itself. Some sit on the intake manifold. Your owner's manual or a service manual for your specific year, make, and model will show the exact location.
To find it without a manual, look for a single-wire electrical connector on the engine block or thermostat area. That connector is almost always the coolant temp sensor. The sensor itself is a small cylindrical part, usually about an inch long, with a hex head that accepts a wrench. Once you've located it, you're ready to start the job.
Draining coolant and removing the old sensor
Let the engine cool completely before you touch anything. A hot engine and hot coolant can cause serious burns. Once it's cool, locate the radiator drain plug at the bottom of the radiator and open it into a drain pan. You don't need to drain the entire system—just enough to drop the coolant level below the sensor location, usually a gallon or two.
Disconnect the electrical connector from the sensor by pressing the release tab or clip and pulling straight out. Then use a socket wrench or sensor socket to unscrew the old sensor. It will come out slowly as you turn it; coolant may drip, so keep the drain pan underneath. Once it's free, pull it straight out of the hole.
Installing the new sensor and refilling coolant
Before you install the new sensor, check whether it comes with a rubber seal or washer already attached. Most do. If not, your old sensor's seal may still be in the hole—fish it out with a small pick or magnet so you don't trap it behind the new sensor.
Thread the new sensor in by hand first to avoid cross-threading. Once it's hand-tight, use your wrench to snug it down. Don't overtighten—these sensors are brass or aluminum and strip easily. A firm hand-tight plus a quarter turn is usually enough. Reconnect the electrical connector until you hear or feel it click into place.
Close the radiator drain plug and refill the radiator with the same coolant type your vehicle uses. Check your owner's manual for the correct type—mixing types can cause problems. Fill until the coolant reaches the cold-fill line on the overflow tank, or the filler neck if there's no overflow tank. Start the engine and let it idle for a few minutes, then check the level again and top off if needed.
Clearing the check engine light
Once the new sensor is in and the coolant is refilled, the check engine light may stay on for a few minutes or a few drive cycles. The computer needs time to read the new sensor and confirm it's working. If the light stays on after 50 to 100 miles of normal driving, the sensor may be bad, or there may be another problem.
You can clear the code yourself with a scan tool if you own one, or you can drive to an auto parts store—many will scan and clear it for free. If the light comes back on when ready, the sensor is likely defective and should be replaced under warranty if it's new.
Tools and parts you'll need
For most vehicles, you need only basic tools: a socket wrench set (usually 19mm, 21mm, or 22mm depending on your vehicle), a drain pan, and a new coolant temperature sensor. Some sensors require a special sensor socket with a slot for the wire, but a regular socket usually works. Check your vehicle's manual or the sensor packaging to confirm the size.
You'll also need the correct coolant type for your vehicle. Don't guess—using the wrong type can cause corrosion inside the engine. Your owner's manual lists the type, or you can ask at an auto parts store with your vehicle's year, make, and model. A gallon of coolant costs $10 to $25 and lasts for multiple top-offs.
When to take it to a shop instead
If your sensor is buried under other components—intake manifolds, alternators, or air boxes—the job becomes much harder and takes longer. Some vehicles require removing multiple parts just to reach the sensor. If you're not comfortable with that level of disassembly, a shop is the better choice.
Also, if you drain coolant and find it's brown, milky, or smells sweet, your coolant may be contaminated or your head gasket may be failing. Those are separate problems that need diagnosis before you replace the sensor. A shop can run a pressure test or chemical test to rule out head gasket failure.
Frequently Asked Questions
How do I know if it's the coolant temp sensor and not something else?
A scan tool will show you the exact code. P0117 and P0118 are coolant temp sensor codes. If you're seeing a different code, the problem is elsewhere. Many auto parts stores will scan your vehicle for free and tell you the code, so you don't need to buy a tool.
Can I drive with a bad coolant temp sensor?
You can drive short distances, but it's risky. Without an accurate temperature reading, the computer can't control the cooling fan properly, and the engine may overheat. You'll also get poor fuel economy and rough idle. It's better to replace it before you take a long trip.
Do I need to bleed air out of the cooling system after I refill it?
Most modern vehicles bleed air automatically as you drive. Fill the radiator to the proper level, start the engine, and let it idle until the fan kicks on. If you have an older vehicle or the manual mentions a bleed procedure, follow those steps. Otherwise, just drive normally and check the level after a few miles.
What if the new sensor doesn't fix the check engine light?
The sensor may be defective, or there may be a wiring problem between the sensor and the computer. Check that the connector is fully seated and the wire isn't pinched or damaged. If the light comes back after 100 miles, the sensor is likely bad and should be replaced again under warranty.
Can I reuse the old sensor if I pull it out by mistake?
No. Once a sensor is removed, the seal is compromised and coolant will leak. Always install a new sensor. The part itself is cheap—$15 to $80—so it's not worth the risk of a coolant leak inside your engine bay.