What drum brakes are and when they need replacement
Drum brakes are a braking system where friction material called brake shoes press against the inside of a rotating drum to slow your vehicle. They're commonly found on the rear wheels of cars and trucks, though some older vehicles have them on all four wheels. Unlike disc brakes, which you can see and inspect easily, drum brakes are enclosed, so wear happens out of sight until the brakes start to fail.
You'll need to replace drum brakes when the brake shoes wear down to the friction material backing, when the drum itself becomes too thin or damaged to be resurfaced, or when the wheel cylinders (the hydraulic components that push the shoes outward) leak or fail. Warning signs include a soft brake pedal, a grinding noise when braking, or brakes that feel weak or pull to one side.
Replacing drum brakes is a moderately involved job that requires basic mechanical skill, the right tools, and time to work carefully. If you've replaced brake pads or done similar suspension work, you can handle this. If you're new to brake work, consider having a shop do it — brake failure is a safety issue, and mistakes are costly.
Key Takeaways
- Drum brake replacement involves removing the wheel, taking off the drum, and replacing the brake shoes, springs, and hardware that have worn out.
- You'll need a jack, jack stands, a drum brake tool kit (which includes a spring removal tool and adjusters), a new drum if the old one is damaged, and new brake shoes and wheel cylinder kits.
- The job typically takes two to four hours per wheel if you work methodically and take photos or notes of how the old assembly was arranged.
- Brake fluid does not need to be changed during a shoe replacement, but the wheel cylinders should be inspected and rebuilt or replaced if they leak.
- After installation, you must bleed the brakes or adjust them so the pedal feels firm and the wheels don't lock up when you brake.
Tools and parts you'll need before you start
Gather everything before you begin, because stopping halfway through to run to a parts store leaves your vehicle unsafe. You'll need a floor jack and jack stands (never work under a car supported only by a jack), a lug wrench to remove the wheel, and a drum brake spring removal tool — this looks like a small hook and is essential because brake springs are under tension and can snap your fingers if you try to remove them by hand.
For the parts themselves, buy a drum brake hardware kit for your specific vehicle year and model — this includes new springs, adjusters, clips, and pins. You'll also need new brake shoes (sold as a set, usually left and right) and a wheel cylinder rebuild kit or a new wheel cylinder. If your drum is scored, cracked, or worn below the minimum thickness (stamped on the drum itself), you'll need a new drum. If the drum is still within spec, it can be reused.
Have a brake cleaner and a brush or compressed air on hand to remove the brake dust, which contains asbestos in older vehicles — never use a regular shop rag or compressed air without a filter. Wear a dust mask and nitrile gloves. You'll also want a small container or magnetic tray to keep springs and hardware organized, and a camera or phone to photograph the old assembly before you disassemble it.
Removing the wheel and drum
Start by parking on a level surface, setting the parking brake, and loosening the lug nuts on the wheel you're working on while the vehicle is still on the ground — this prevents the wheel from spinning when you lift it. Then place the jack under the vehicle's frame (not the bumper or plastic trim) and raise it until the wheel is about six inches off the ground. Slide jack stands under the frame on both sides of the wheel and lower the vehicle onto them.
Remove the lug nuts completely and pull the wheel straight toward you. If the drum is pressed onto the hub, it may not come off when ready. Spray penetrating oil around the center where the drum meets the hub, wait a few minutes, then tap the drum gently with a rubber mallet around its edge. Do not hit it hard — you're trying to break the corrosion seal, not damage the drum. Once it moves, pull it straight off.
If the drum still won't budge, look for a small rubber plug on the back of the backing plate (the metal plate behind the drum). Remove it and you'll see a small adjuster wheel. Turn this wheel backward (away from you) to loosen the brake shoes, which will give you clearance to pull the drum off. Take a photo of the entire brake assembly before you touch anything — you'll refer to this when reassembling.
Disassembling the old brake assembly
The brake assembly consists of two curved brake shoes held in place by springs, adjusters, and a wheel cylinder. Start by using your spring removal tool to unhook the upper return spring (the larger spring connecting the tops of the shoes). Work slowly — these springs are under load. Once the upper spring is off, remove the lower return spring the same way.
Next, remove the hold-down springs and pins. These look like a spring wrapped around a pin that goes through the backing plate. Use the spring removal tool to compress the spring while you turn the pin 90 degrees, then slide the pin out. Do this for both shoes. As you remove each component, place it on your magnetic tray or in a small container in the order you removed it — this makes reassembly much faster.
Once the springs and pins are off, the shoes should pull away from the backing plate. The wheel cylinder will still be attached to the backing plate. Inspect it for leaks (wet spots or fluid around the rubber seals). If it's leaking, you'll need to rebuild it or replace it. If it's dry, you can reuse it, but many shops replace it as routine maintenance since you have the drum off anyway.
Inspecting and preparing the backing plate and drum
With the shoes removed, clean the entire backing plate with brake cleaner and a brush. Remove all dust, dirt, and old brake material. Look for scoring or damage on the backing plate itself — if it's cracked or severely worn, it should be replaced. Check the wheel cylinder for leaks and corrosion. If it's leaking, remove it now by unbolting it from the backing plate and disconnecting the brake line.
Inspect the drum for cracks, deep scoring, or a glazed (shiny, hardened) surface. If the drum is glazed, it can be resurfaced by a machine shop — this removes a thin layer and restores the friction surface. If it's cracked or scored too deeply to resurface, or if it's already been resurfaced to its minimum thickness (check the stamped number on the drum), replace it with a new one. A drum that's too thin will overheat and fail.
If you're reusing the drum, wipe it clean with brake cleaner and let it dry. If you're installing a new drum, remove any protective coating or rust with brake cleaner and a wire brush. Do not touch the inside friction surface with your bare hands — the oils from your skin will contaminate it and cause brake noise.
Installing the new brake shoes and hardware
Start by installing the wheel cylinder (new or rebuilt) if you removed it. Bolt it to the backing plate and reconnect the brake line, then bleed that wheel later. If you're keeping the old cylinder, inspect the rubber seals and make sure they're not cracked or leaking.
Install the new brake shoes by sliding them onto the backing plate and positioning them so the wheel cylinder pushes against them. The shoes should sit flat against the backing plate with no gaps. Install the hold-down springs and pins in the same locations where the old ones were — use your photo as a reference. Compress the spring with your tool, insert the pin, and turn it 90 degrees to lock it in place.
Now install the return springs. The upper return spring connects the tops of the shoes and is usually the stiffer of the two. Hook it onto both shoes and pull it tight. Install the lower return spring the same way. The shoes should now be held firmly in place and centered on the backing plate. If they're crooked or loose, remove the springs and reposition the shoes.
Install the adjuster mechanism (the star wheel and its housing) between the shoes at the bottom, following the orientation shown in your photo of the old assembly. The adjuster allows you to tighten the shoes to the drum after installation. Make sure all springs are seated properly and nothing is rubbing or twisted.
Reinstalling the drum and wheel
Slide the drum back onto the hub. It should fit over the new shoes with minimal resistance — if it's tight, the shoes are too close to the drum. Use the adjuster wheel (accessed through the rubber plug on the backing plate) to back off the shoes slightly, then try again. Once the drum slides on smoothly, install the wheel and lug nuts by hand, then lower the vehicle onto the ground.
Tighten the lug nuts in a star pattern (opposite sides alternately) to the torque specification for your vehicle — this is usually between 80 and 120 foot-pounds, but check your owner's manual. Do not over-tighten, as this can warp the rotor or drum.
Now you need to adjust the brake shoes so they're close to the drum without dragging. Access the adjuster wheel through the rubber plug on the backing plate and turn it forward (toward you) until you hear or feel the shoes touching the drum, then back it off just slightly so the wheel spins freely with no rubbing. Repeat this for each wheel you worked on.
Testing the brakes and what to do next
Before driving, pump the brake pedal several times while the vehicle is parked. The pedal should feel firm and not sink to the floor. If it does sink, you may have air in the brake lines or a leak. Start the engine and test the brakes at low speed in a safe area — the brakes should feel responsive and not pull to one side. If they pull, the shoes may not be adjusted evenly or one wheel cylinder may not be working.
Drive for a few miles at moderate speeds, then find a safe place to stop and feel the wheels — they should be warm but not hot. If one wheel is much hotter than the others, that brake is dragging and needs adjustment. After the first 50 to 100 miles, stop and re-check the adjustment, as new shoes settle slightly as they bed in to the drum.
If you had to bleed the brakes (because you disconnected the brake line at the wheel cylinder), follow your vehicle's bleeding procedure, starting at the wheel farthest from the master cylinder and working toward the closest. If you didn't disconnect the line, bleeding is not necessary.
Frequently Asked Questions
Do I have to replace the wheel cylinder when I replace the brake shoes?
No, but you should inspect it. If it's leaking fluid, has a cracked rubber seal, or feels spongy when you push on it, replace it. If it's dry and moves smoothly, it can be reused. Many shops replace it anyway since you have the drum off, because a failing cylinder will make the new shoes wear unevenly.
Can I replace just one wheel's brakes, or do I have to do both rear wheels?
You can replace one wheel at a time, but brake wear is usually even on both sides. If one side is worn enough to need replacement, the other is probably close behind. Replacing both at the same time ensures even braking and prevents one side from dragging.
What if the drum won't come off even after I loosen the adjuster?
Spray penetrating oil around the seam where the drum meets the hub and let it soak for 15 to 30 minutes. Tap gently with a rubber mallet all the way around the edge. If it still won't move, the drum may be cracked or the hub may be damaged — stop and have a shop assess it rather than forcing it.
How long do new drum brakes last?
Brake shoe life depends on your driving habits and vehicle weight, but typically ranges from 30,000 to 60,000 miles. Frequent city driving with lots of braking wears them faster than highway driving. Check them every 20,000 miles or during routine maintenance.
Do I need to bleed the brakes after replacing drum brake shoes?
Only if you disconnected the brake line at the wheel cylinder. If you left the line connected, no bleeding is needed. If you did disconnect it, bleed that wheel following your vehicle's procedure to remove air from the line.