Brake light bulbs burn out faster than you might expect, and a burned-out bulb is both a safety hazard and a traffic violation in every state
Replacing a brake light bulb is one of the few brake repairs you can do yourself in under ten minutes, with no special tools beyond a screwdriver. The bulb sits in a socket at the back of your vehicle, and you access it from inside the trunk or cargo area. The job is straightforward: remove the lens cover, twist out the old bulb, and push in a new one that matches your vehicle's specification.
A burned-out brake light means drivers behind you cannot see when you are slowing down. This creates a real collision risk, especially in heavy traffic or at night. It is also illegal — police can stop you for a broken brake light, and you may receive a citation. Replacing the bulb takes longer to schedule at a shop than to do it yourself, and you will pay a service fee on top of the bulb cost.
Key Takeaways
- Brake light bulbs are accessed from inside your trunk or cargo area and require only a screwdriver to remove the lens cover.
- You must buy the correct bulb type for your vehicle — check your owner's manual or the part number on the old bulb before you shop.
- The bulb twists counterclockwise out of its socket; do not pull straight out, or you may break the socket.
- A burned-out brake light is a safety problem and a traffic violation, so replace it as soon as you notice it is not working.
Locate the brake light assembly from inside your vehicle
Open your trunk or cargo door and look at the inner surface of the rear panel, directly behind where the brake light sits on the outside. You will see either a plastic lens cover held in place by screws, or a cover that twists out by hand. Some vehicles have the bulb socket accessible without removing the lens — you may see a rubber access port or a small opening where you can reach the socket directly.
If your vehicle has a hatchback or liftgate, the brake lights are usually mounted on the inside edges of the cargo area, near the top corners. Sedans and coupes typically have brake lights in the rear quarter panel, accessible through the trunk. Trucks and SUVs vary widely, so check your owner's manual if you cannot locate the assembly from the trunk opening.
Remove the lens cover or access panel
If the cover is held by screws, use a Phillips or flathead screwdriver (depending on the screw type) to remove them. Keep the screws in a small container so you do not lose them — they are straightforward to drop inside the trunk. Set the lens cover aside in a safe place where it will not get scratched or cracked.
If the cover twists out, grip it firmly and turn it counterclockwise. It will come free after a quarter turn or so. Do not force it; if it does not move easily, you may have the wrong cover or there may be a locking tab you need to release first. Check your owner's manual for the exact removal method if you are unsure.
Identify the correct bulb type before you buy a replacement
Look at the bulb socket inside the assembly. The bulb will have a part number printed on its base or on the socket itself. Common brake light bulbs are 1157 (dual-filament, used for brake and running lights), 1156 (single-filament, brake light only), or 7440 (wedge-base, used in some newer vehicles). Write down this number or take a photo of the old bulb.
Your owner's manual will also list the correct bulb type in the maintenance section, usually under "Bulb Specifications" or "Light Bulbs." If you have lost your manual, you can search your vehicle's year, make, and model online, or ask an auto parts store — they can look it up by your vehicle's information. Buying the wrong bulb type means it will not fit the socket or will not work correctly, so take time to get this right.
Remove the old bulb and install the new one
Grip the bulb firmly and twist it counterclockwise. It will rotate about a quarter turn before it comes free from the socket. Do not pull straight out — twisting is the correct motion, and pulling can damage the socket or break the bulb. Once the bulb is loose, pull it straight out of the socket.
Insert the new bulb into the socket, aligning the pins or tabs on the bulb base with the slots in the socket. Push it in gently and twist it clockwise until it stops. You should feel a slight resistance as it seats fully. Do not force it; the bulb should click or seat smoothly into place. If it does not, remove it and check that you have the correct bulb type.
Test the brake light before reassembling
Before you put the lens cover back on, have someone press the brake pedal while you watch the light from outside the vehicle. The new bulb should light up brightly and consistently. If it does not light, remove it and check that it is seated fully in the socket. If the bulb is seated correctly and still does not work, the socket itself may be damaged or corroded, and you will need to have it inspected by a technician.
If the light works, reinstall the lens cover by reversing the removal process. If you removed screws, replace them and tighten them snugly — do not over-tighten, as you can crack the plastic. If the cover twists on, align it with the assembly and turn it clockwise until it stops.
When to have a technician check the brake light circuit
If you have replaced the bulb and it still does not light, the problem is not the bulb itself. The issue could be a corroded socket, a broken wire, a blown fuse, or a faulty brake light switch. These are electrical problems that require diagnostic equipment to locate and repair safely.
A corroded socket can sometimes be cleaned with a small wire brush or by spraying electrical contact cleaner into the socket, but if the corrosion is severe, the socket may need to be replaced. A blown fuse is straightforward to check — your owner's manual shows the fuse box location and which fuse controls the brake lights — but if the fuse blows again after replacement, there is an electrical short that a technician must find. A faulty brake light switch means the lights will not come on at all, even though the bulbs are good. Do not ignore a brake light that will not work after you have replaced the bulb; have it inspected before you drive the vehicle regularly.
Frequently Asked Questions
Do I need to disconnect the battery before replacing a brake light bulb?
No. Brake light bulbs operate on low voltage and pose no shock hazard. Disconnecting the battery is unnecessary and will reset your vehicle's computer and radio settings. straightforward turn off the engine and work on the light assembly as described.
Can I use a higher-wattage bulb to make the brake light brighter?
No. Using a bulb with a higher wattage than the manufacturer specifies can overheat the socket, melt the plastic lens, or damage the wiring. The correct bulb type is designed to work with your vehicle's electrical system. If the light seems dim, the socket may be corroded or the lens may be cloudy — have it inspected.
What if the bulb socket is cracked or corroded?
A cracked socket will not hold a bulb securely and may cause electrical problems. Corrosion inside the socket prevents good contact between the bulb and the socket. Both issues require the socket to be replaced, which usually means replacing the entire light assembly. This is a job for a technician, as it may involve removing trim panels or wiring.
How often do brake light bulbs burn out?
Brake light bulbs typically last between 1,000 and 2,000 hours of use, which translates to several years for most drivers. Frequent braking in city driving wears bulbs faster than highway driving. Check your brake lights every few months by having someone watch them while you press the pedal, or look at the reflection in a garage door or storefront window.
Is it normal for both brake lights to burn out at the same time?
Bulbs usually burn out one at a time, but if both brake lights fail at once, the problem is likely not the bulbs — it is probably a blown fuse, a faulty brake light switch, or a broken wire. Replace one bulb to confirm it works, then have the electrical system inspected if the other light still does not work.